Juniper-ETHERNET-MIB Table View

The parameters for the Ethernet interface.

juniEthernetIfEntry row .1.3.6.1.4.1.4874.2.2.34.1.1.1.1

The Parameters for a particular Ethernet interface. Entries in this
table correspond with entries in the ifTable/ifXTable/juniIfTable.

Indexes

juniEthernetIfIndex

Column	Syntax	OID
juniEthernetIfIndex The ifIndex value of the corresponding ethernet interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.1
juniEthernetIfDuplexMode The configured duplex setting for this ethernet interface. The operational value is reported in this table entry's corresponding juniEthernetIfOperDuplexMode object. NOTE, configuration dependency: …	Enumerationr/w Enumerated Values: 1 autoDuplex 2 halfDuplex 3 fullDuplex	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.2
juniEthernetIfSpeed The configured speed setting for this ethernet interface. The operational value is reported in the corresponding Interfaces MIB ifSpeed object. NOTE, configuration dependency: Setting this…	Enumerationr/w Enumerated Values: 1 autoNegotiate 2 speed10Mbps 3 speed100Mbps 4 speed1000Mbps 5 speed10000Mbps	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.3
juniEthernetIfMtu The configured maximum transfer unit (MTU) for this ethernet interface. The operational value is reported in the corresponding Interfaces MIB ifMtu object.	Integer32r/w Constraints: range: 64-9188	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.4
juniEthernetIfOperDuplexMode The current operational duplex mode for this ethernet interface.	Enumeration Enumerated Values: 1 autoDuplex 2 halfDuplex 3 fullDuplex	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.5
juniEthernetIfPrimaryMauType The primary MAU type.	JuniEthernetIfMauType Type Values: 0 mauNotPresent 1 mauNotSupported 2 mau10BaseT 3 mau100BaseTx 4 mau1000BaseT 5 mau1000BaseCx 6 mau1000BaseSx 7 mau1000BaseLx 8 mau1000BaseZx 9 mauSfpUnknown 10 mauSfpNotPresent 11 mau100BaseFxSm 12 mau100BaseFxMm 13 mauSfpNotJnprCompliant 14 mau10000BaseSr 15 mau10000BaseLr 16 mau10000BaseEr 17 mauXfpUnknown 18 mauXfpNotPresent 19 mauXfpNotJnprCompliant	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.6
juniEthernetIfSecondaryMauType The secondary MAU type for those ports that support a secondary.	JuniEthernetIfMauType Type Values: 0 mauNotPresent 1 mauNotSupported 2 mau10BaseT 3 mau100BaseTx 4 mau1000BaseT 5 mau1000BaseCx 6 mau1000BaseSx 7 mau1000BaseLx 8 mau1000BaseZx 9 mauSfpUnknown 10 mauSfpNotPresent 11 mau100BaseFxSm 12 mau100BaseFxMm 13 mauSfpNotJnprCompliant 14 mau10000BaseSr 15 mau10000BaseLr 16 mau10000BaseEr 17 mauXfpUnknown 18 mauXfpNotPresent 19 mauXfpNotJnprCompliant	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.7
juniEthernetIfPrimaryLength The rated cable length in meters for the primary MAU. If the value is 0, the length is unspecified.	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.8
juniEthernetIfSecondaryLength The rated cable length in meters for the secondary MAU for those ports that support a secondary. If the value is 0, the length is unspecified.	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.4874.2.2.34.1.1.1.1.9

This table contains entries for Ethernet Subinterfaces present in the
system.

juniEthernetSubIfEntry row .1.3.6.1.4.1.4874.2.2.34.1.2.2.1

Each entry describes the characteristics of an Ethernet Subinterface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable.

Indexes

juniEthernetSubIfIndex

Column	Syntax	OID
juniEthernetSubIfIndex The ifIndex of the Ethernet Subinterface. When creating entries in this table, suitable values for this object are determined by reading juniEthernetSubNextIfIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.34.1.2.2.1.1
juniEthernetSubIfRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.34.1.2.2.1.2
juniEthernetSubIfLowerIfIndex The ifIndex of a Ethernet interface over which this Ethernet Subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry cre…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.34.1.2.2.1.3
juniEthernetSubIfId An integer identifier for the Ethernet subinterface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among subinterfac…	Integer32r/w Constraints: range: -1-2147483647	.1.3.6.1.4.1.4874.2.2.34.1.2.2.1.4

This table contains entries for major VLAN interfaces present in the
system.

juniVlanMajorIfEntry row .1.3.6.1.4.1.4874.2.2.34.1.3.2.1

Each entry describes the characteristics of a major VLAN interface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable.

Indexes

juniVlanMajorIfIndex

Column	Syntax	OID
juniVlanMajorIfIndex The ifIndex of the major VLAN interface. When creating entries in this table, suitable values for this object are determined by reading juniVlanMajorNextIfIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.34.1.3.2.1.1
juniVlanMajorIfLowerIfIndex The ifIndex of the interface over which this major VLAN interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.34.1.3.2.1.2
juniVlanMajorIfRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create or delete an entr…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.34.1.3.2.1.3

This table contains entries for VLAN Subinterfaces present in the
system.

juniVlanSubIfEntry row .1.3.6.1.4.1.4874.2.2.34.1.4.2.1

Each entry describes the characteristics of a VLAN Subinterface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable.

Indexes

juniVlanSubIfIndex

Column	Syntax	OID
juniVlanSubIfIndex The ifIndex of the VLAN Subinterface. When creating entries in this table, suitable values for this object are determined by reading juniVlanSubNextIfIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.1
juniVlanSubIfVlanId An integer identifier or tag ID for this VLAN A value of zero indicates the default VLAN. When VLANs are enabled, the value must be unique among subinterfaces configured on the same underlying major VLAN …	Integer32r/w Constraints: range: 0-4095 range: 5000-5001	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.2
juniVlanSubIfVlanUntagged When VLANs are enabled, this allows tagged frames to be received, while transmitted frames remain untagged. This can only be enabled when the juniVlanSubIfVlanId field is zero.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.3
juniVlanSubIfLowerIfIndex The ifIndex of VLAN major interface over which this VLAN Subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creati…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.4
juniVlanSubIfRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.5
juniVlanSubIfVlanStackId An integer identifier or tag ID for this S-VLAN. When S-VLANs are enabled, the VLAN and S-VLAN ID valuse must be unique among subinterfaces configured on the same underlying major VLAN interface. …	Integer32r/w Constraints: range: 0-4095 range: 5000-5000	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.6
juniVlanSubIfVlanStackEthertype The ethertype is used to recognize and demultiplex traffic for this S-VLAN. Must be either 0x8100, 0x88a8, or 0x9100.	Enumerationr/w Enumerated Values: 33024 etherType8100h 34984 etherType88a8h 37120 etherType9100h	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.7
juniVlanSubIfVlanAdvisoryRxSpeed Advisory receive speed, in kilobits per second (kbps), of this subinterface. This object has no impact on forwarding performance but may be used as a hint for underlying circuit receive speed.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.8
juniVlanSubIfVlanAdvisoryTxSpeed Advisory transmit speed, in kilobits per second (kbps), of this subinterface. This object has no impact on forwarding performance but may be used as a hint for underlying circuit transmit speed.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4874.2.2.34.1.4.2.1.9

The parameters for the Ethernet interface statistics.

juniEthernetIfStatsEntry row .1.3.6.1.4.1.4874.2.2.34.1.5.1.1

The Parameters for a particular Ethernet interface statistics.

Indexes

juniEthernetIfStatsIndex

Column	Syntax	OID
juniEthernetIfStatsIndex The ifIndex value of the corresponding ethernet interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.34.1.5.1.1.1
juniEthernetIfIngressLineUtilization The ingress line utilization statistic for this ethernet interface.	percentUnsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.4874.2.2.34.1.5.1.1.2
juniEthernetIfEgressLineUtilization The egress line utilization statistic for this ethernet interface.	percentUnsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.4874.2.2.34.1.5.1.1.3