HH3C-POWER-ETH-EXT-MIB Table View

The indexing scheme is taken form that used by
the IETF Power MIB.  The same indexing scheme is
used to give continuity in behaviour between
that standard and this extensions definitioin.

hh3cPsePortEntry row .1.3.6.1.4.1.25506.2.14.1.1

The pethPsePortGroupIndex is imported from the IETF Power MIB
and uniquely identifies the group containing the port to which
power ethernet PSE is connected. Group means (box in the stack,
module in a rack).
…

Indexes

POWER-ETHERNET-MIBpethPsePortGroupIndex POWER-ETHERNET-MIBpethPsePortIndex

Column	Syntax	OID
hh3cPsePortFaultDescription The object supports the fault category of the IETF Power MIB [1] pethPsePortDetectionStatus object. A textual description containing more information about the nature of this fault is provided by this object. Typicall…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.25506.2.14.1.1.2
hh3cPsePortPeakPower The object specifies the peak power which has been consumed by the port. It is defined as the highest measured value of power in milliWatts that has been consumed by the port. Its value is only reset when link is lost…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.1.1.3
hh3cPsePortAveragePower The object specifies the average power which has been consumed by the port. This object is a read/write integer value with units of milliWatts. Writing a value of zero to this object resets its value to zero. Writing…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.1.1.4
hh3cPsePortCurrentPower The object specifies the power currently being consumed by the port. It is a read only integer value with units of milliWatts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.1.1.5
hh3cPsePortPowerLimit The object specifies the power limit set for this port. The PSE will not supply more than this level of power to the specified port. It is a read/write integer value with units of milliWatts.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.1.1.6
hh3cPsePortProfileIndex Indicates the power profile which is currently associated with this port. This object references the corresponding hh3cPseProfileIndex object in the power profiles table. A value of zero is a special case and indicate…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.25506.2.14.1.1.7
hh3cPsePortTrackAction Action taken when the state of the track entry associated with the PoE port changes from positive to negative. none(0):None. alarm(1):Outputs alarm information. alarmRebootPD(2):Outputs alarm information and restarts th…	Enumeration Enumerated Values: 0 none 1 alarm 2 alarmRebootPD	.1.3.6.1.4.1.25506.2.14.1.1.8

Description.

hh3cMainPseEntry row .1.3.6.1.4.1.25506.2.14.2.1

The pethMainPseGroupIndex is imported from the IETF Power MIB
and uniquely identifies the group containing the port to which
power ethernet PSE is connected. Group means (box in the stack,
module in a rack) and the val…

Indexes

POWER-ETHERNET-MIBpethMainPseGroupIndex

Column	Syntax	OID
hh3cMainPsePowerLimit The object specifies the power limit set for the unit as a whole. The PoE unit will already have a nominal power defined by the IETF Power MIB [1] pethMainPsePower object. This OPTIONAL object specifies a further limit…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.2.1.1
hh3cMainPseAveragePower The object specifies the average power which has been consumed by the port. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.2.1.2
hh3cMainPsePeakPower The object specifies the peak power which has been consumed for PoE. It is defined as the highest measured value of power in milliWatts that has been consumed at any one point in time by the sum of the PoE ports. Its v…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.2.1.3
hh3cMainGuaranteedPowerRemaining The object specifies the amount of power remaining in the guaranteed power pool. Each time a port is placed into guaranteed mode it reserves a set amount of power out of the total guaranteed power pool for the system. …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.2.1.4
hh3cMainPsePriorityMode Describes or controls the priority mode on slot which must be enabled firstly. When a new board is inserted, and the power is over-load, a value of disconnection(0) means that the power will stop supply to the low prio…	Enumerationr/w Enumerated Values: 0 disconnection 1 non-disconnection	.1.3.6.1.4.1.25506.2.14.2.1.5
hh3cMainPseLegacy Describes or controls the legacy mode on slot which must be enabled firstly. Legacy mode: standard or nonstandard PD detection mode.	Enumerationr/w Enumerated Values: 0 enable 1 disable	.1.3.6.1.4.1.25506.2.14.2.1.6
hh3cMainPsePowerPriority Describes or controls the priority of the PSE. The priority will be used by the PSE policy to prevent from power overloading. If the priority of PSE is set to critical, the PSE will turn into guaranteed mode. The prio…	Enumerationr/w Enumerated Values: 1 critical 2 high 3 low	.1.3.6.1.4.1.25506.2.14.2.1.7

A table of objects representing a set of power profiles.
Power profiles can be applied to PoE ports, which have the
effect of automatically setting the priority, power limit
and PoE enable MIB objects to the values specified in the
power profile.

hh3cPseProfilesEntry row .1.3.6.1.4.1.25506.2.14.7.1

A set of objects that display and control the Main power of a PSE.

Indexes

hh3cPseProfileIndex

Column	Syntax	OID
hh3cPseProfileIndex The index of the profile. This uniquely allow the profile to be identified.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.25506.2.14.7.1.1
hh3cPseProfileName Assigns the profile a name with which the settings can be assiciated with. For example, 'NBX Phone'.	OctetStringr/w Constraints: range: 1-15	.1.3.6.1.4.1.25506.2.14.7.1.2
hh3cPseProfilePowerMode The power mode associated with this power profile. There are two possible power modes as follows: powerDisabled, powerEnabled. When a power profile is applied to a PSE port, this value dictates the settings of the por…	Enumerationr/w Enumerated Values: 1 powerDisabled 2 powerEnabled	.1.3.6.1.4.1.25506.2.14.7.1.3
hh3cPseProfilePowerLimit The power limit to be applied to the ports hh3cPsePortPowerLimit object when the profile is applied to the PSE port. Expressed in milliWatts.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.7.1.4
hh3cPseProfilePriority This object controls the priority of the port from the point of view of a power management algorithm. The priority that is set by this variable could be used by a control mechanism that prevents over current situations…	Enumerationr/w Enumerated Values: 1 critical 2 high 3 low	.1.3.6.1.4.1.25506.2.14.7.1.5
hh3cPseProfilePairs Describes or controls the pairs in use. If the value of pethPsePortPowerPairsControl is true, this object is writable. A value of signal(1) means that the signal pairs only are in use. A value of spare(2) means that th…	Enumerationr/w Enumerated Values: 1 signal 2 spare	.1.3.6.1.4.1.25506.2.14.7.1.6
hh3cPseProfileApplyNum The number of this profile which has been applied. If hh3cPseProfileApplyNum is not zero, user can't change the current line.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.7.1.7
hh3cPseProfileRowStatus The status of this classifier. If hh3cPseProfileApplyNum is not zero, user can't delete the current line.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.25506.2.14.7.1.8

The table of the module information on this POE power.

hh3cPOEModuleInfoEntry row .1.3.6.1.4.1.25506.2.14.8.2.7.1

The entry of the module information on this POE power.

Indexes

hh3cPOEModuleIndex

Column	Syntax	OID
hh3cPOEModuleIndex The index of the current module on this POE power. It is also the index of hh3cPOEModuleInfoTable. The range of this node is from 1 to hh3cPOEPowerModuleNum.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.25506.2.14.8.2.7.1.1
hh3cPOEModuleID The ID of the current module on this POE power.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.8.2.7.1.2
hh3cPOEModuleInfoPower The power of the current module on this POE power.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.25506.2.14.8.2.7.1.3
hh3cPOEModuleHardVerInfo The hardware version information of the current module on this POE power.	OctetString Constraints: range: 1-127	.1.3.6.1.4.1.25506.2.14.8.2.7.1.4

The table of DC output power state on this POE power.

hh3cPOEDCOutStateEntry row .1.3.6.1.4.1.25506.2.14.8.3.2.1

The entry of the DC output power state on this POE power.

Indexes

hh3cPOEDCOutStateIndex

Column	Syntax	OID
hh3cPOEDCOutStateIndex The index of the DC output power state on this POE power. The range of this node is from 1 to hh3cPOEDCOutStateModuleNum.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.25506.2.14.8.3.2.1.1
hh3cPOEDCOutDCVolAlarm The DC output alarm of the DC output power state on this POE power. The value of this node will be the following values: normal (1), underLimit (2), aboveL…	DCAlarmState Type Values: 1 normal 2 underLimit 3 aboveLimit 4 fuseBroken 5 switchOff 6 otherError	.1.3.6.1.4.1.25506.2.14.8.3.2.1.2

The table of the DC output information on this POE power.

hh3cPOEDCOutInfoEntry row .1.3.6.1.4.1.25506.2.14.8.4.2.1

The entry of the DC output information on this POE power.

Indexes

hh3cPOEDCOutInfoIndex

Column	Syntax	OID
hh3cPOEDCOutInfoIndex The index of the DC output information on this POE POWER. The range of this node is from 1 to hh3cPOEDCOutCurNum.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.25506.2.14.8.4.2.1.1
hh3cPOEDCOutVol The DC output voltage of the current DC output on this POE power.	OctetString Constraints: range: 1-10	.1.3.6.1.4.1.25506.2.14.8.4.2.1.2
hh3cPOEDCOutInfoLoadCur The total load current of the current DC output on this POE power.	OctetString Constraints: range: 1-10	.1.3.6.1.4.1.25506.2.14.8.4.2.1.3

The table of the AC switch state on this POE power.

hh3cPOEACSwitchStateEntry row .1.3.6.1.4.1.25506.2.14.8.5.2.1

The entry of the AC switch state on this POE power.

Indexes

hh3cPOEACSwitchStateIndex

Column	Syntax	OID
hh3cPOEACSwitchStateIndex The index of the AC switch state on this POE power. The range of this node is from 1 to hh3cPOEACSwitchStateModuleNum.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.25506.2.14.8.5.2.1.1
hh3cPOEACSwitchState The AC switch state on this POE power. The value of this node will be one of the following values: on (1), off (2), highVoltInput (3), …	SwitchState Type Values: 1 on 2 off 3 highVoltInput 4 lowVoltInput	.1.3.6.1.4.1.25506.2.14.8.5.2.1.2

All alarm status of the VOL status.
The value of this node will be one of the following values:
                    normal     (1),
                    underLimit (2),
                    aboveLimit (3),
                    lackPhrase (4),
                    fuseBroken (5),
                    switchOff  (6),
                    otherError (7).

hh3cPOESwitchStateVolExEntry row .1.3.6.1.4.1.25506.2.14.8.6.5.1

The hh3cPOESwitchStateVolExIndex will match the number of the VOL status.

Indexes

hh3cPOESwitchStateVolExIndex

Column	Syntax	OID
hh3cPOESwitchStateVolExIndex The object species the index of the VOL status. The range of this node is from 1 to hh3cPOEInCurStateModuleNum.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.25506.2.14.8.6.5.1.1
hh3cPOESwitchStateInVolAB The object specifies the VOL AB alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimi…	ACAlarmState Type Values: 1 normal 2 underLimit 3 aboveLimit 4 lackPhrase 5 fuseBroken 6 switchOff 7 otherError	.1.3.6.1.4.1.25506.2.14.8.6.5.1.2
hh3cPOESwitchStateInVolBC The object specifies the VOL BC alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimi…	ACAlarmState Type Values: 1 normal 2 underLimit 3 aboveLimit 4 lackPhrase 5 fuseBroken 6 switchOff 7 otherError	.1.3.6.1.4.1.25506.2.14.8.6.5.1.3
hh3cPOESwitchStateInVolCA The object specifies the VOL CA alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimi…	ACAlarmState Type Values: 1 normal 2 underLimit 3 aboveLimit 4 lackPhrase 5 fuseBroken 6 switchOff 7 otherError	.1.3.6.1.4.1.25506.2.14.8.6.5.1.4

All alarm states in the POE power modules.

hh3cPOEAlarmStateInfoEntry row .1.3.6.1.4.1.25506.2.14.8.7.2.1

The hh3cPOEAlarmModuleInfoIndex will match the number
of the power module.

Indexes

hh3cPOEAlarmModuleInfoIndex

Column	Syntax	OID
hh3cPOEAlarmModuleInfoIndex The index specifies the index of the Hh3cPOEAlarmStateInfoEntry table. The range of this node is from 1 to hh3cPOEAlarmStateModuleNum.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.25506.2.14.8.7.2.1.1
hh3cPOEModuleDisconnect The node specifies the alarm state: The module does not link. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.2
hh3cPOEModuleInputError The node specifies the alarm state: Input error. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.3
hh3cPOEModuleOutputError The node specifies the alarm state: Output error. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.4
hh3cPOEModuleOverVoltage The node specifies the alarm state: The voltage is too high. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.5
hh3cPOEModuleOverTemp The node specifies the alarm state: The temperature is too high. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.6
hh3cPOEModuleFanError The node specifies the alarm state: The fan error. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.7
hh3cPOEModuleShutdown The node specifies the alarm state: The module is shutdown. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.8
hh3cPOEModuleCurRestricted The node specifies the alarm state: The module limit the current. The value of this node is one of the following values: normal (1), alarm (2).	ModuleAlarmState Type Values: 1 normal 2 alarm	.1.3.6.1.4.1.25506.2.14.8.7.2.1.9