ES3552M-AND-PoE-MIB Table View

Table of descriptive and status information about
the switch units in this system.

switchInfoEntry row .1.3.6.1.4.1.259.8.1.12.1.1.3.1

Table providing descriptions and status information for
switch units.

Indexes

swUnitIndex

Column	Syntax	OID
swUnitIndex This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.1
swHardwareVer Hardware version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.2
swMicrocodeVer Microcode version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.3
swLoaderVer Loader version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.4
swBootRomVer Boot ROM code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.5
swOpCodeVer Operation code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.6
swPortNumber The number of ports on this switch.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.7
swPowerStatus Indicates the switch using internalPower(1), redundantPower(2) or both(3)	Enumeration Enumerated Values: 1 internalPower 2 redundantPower 3 internalAndRedundantPower	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.8
swRoleInSystem Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.	Enumeration Enumerated Values: 1 master 2 backupMaster 3 slave	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.9
swSerialNumber Serial number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.10
swServiceTag Service tag serial-number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.13
swModelNumber Model number of the switch.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.14
swEpldVer The EPLD version of the switch.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.1.3.1.15

Table about the status of individual powers.

switchIndivPowerEntry row .1.3.6.1.4.1.259.8.1.12.1.1.6.1

Table about the status of individual power.

Indexes

swIndivPowerUnitIndex swIndivPowerIndex

Column	Syntax	OID
swIndivPowerUnitIndex This is defined as swUnitIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.1.6.1.1
swIndivPowerIndex 1 means internal power, 2 means external power.	Enumeration Enumerated Values: 1 internalPower 2 externalPower	.1.3.6.1.4.1.259.8.1.12.1.1.6.1.2
swIndivPowerStatus notPresent(1) means not present, green(2) means up, red(3) means down.	Enumeration Enumerated Values: 1 notPresent 2 green 3 red	.1.3.6.1.4.1.259.8.1.12.1.1.6.1.3

Table of descriptive and status information describing
the configuration of each switch port. This table also
contains information about each trunk.

portEntry row .1.3.6.1.4.1.259.8.1.12.1.2.1.1

An entry in the table, describing the configuration of
one switch port or trunk.

Indexes

portIndex

Column	Syntax	OID
portIndex The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.1
portName The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.2
portType Indicates the port type of the configuration of the switch.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseSfp 9 hundredBaseFxScSingleMode 10 hundredBaseFxScMultiMode 11 thousandBaseCX 12 tenG	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.3
portSpeedDpxCfg Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half…	Enumerationr/w Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.4
portFlowCtrlCfg (1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 5 tx 6 rx	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.5
portCapabilities Port or trunk capabilities.	Bitsr/w Enumerated Values: 0 portCap10half 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 portCap10gHalf 7 portCap10gFull 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.6
portAutonegotiation Whether auto-negotiation is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.7
portSpeedDpxStatus The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case t…	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.8
portFlowCtrlStatus (2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently confi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.9
portTrunkIndex The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding tru…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.10
portComboForcedMode This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal…	Enumerationr/w Enumerated Values: 1 none 2 copperForced 3 copperPreferredAuto 4 sfpForced 5 sfpPreferredAuto	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.12
portMasterSlaveModeCfg Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.	Enumerationr/w Enumerated Values: 1 master 2 slave 3 auto 4 autoPreferMaster 5 autoPreferSlave	.1.3.6.1.4.1.259.8.1.12.1.2.1.1.15

Table for cable diagnostics result.

cableDiagResultEntry row .1.3.6.1.4.1.259.8.1.12.1.2.3.2.1

Entry for cable diagnostics result.

Indexes

cableDiagResultIfIndex

Column	Syntax	OID
cableDiagResultIfIndex This is defined as the ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.3.2.1.1
cableDiagResultStatusPairA The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack …	Enumeration Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 5 openShort 6 crosstalk 7 unknown 8 impedanceMismatch 9 fail 10 notSupport	.1.3.6.1.4.1.259.8.1.12.1.2.3.2.1.2
cableDiagResultStatusPairB The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack …	Enumeration Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 5 openShort 6 crosstalk 7 unknown 8 impedanceMismatch 9 fail 10 notSupport	.1.3.6.1.4.1.259.8.1.12.1.2.3.2.1.3
cableDiagResultDistancePairA Displays the fault distance of pair A of the cable in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.3.2.1.6
cableDiagResultDistancePairB Displays the fault distance of pair B of the cable in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.3.2.1.7
cableDiagResultTime Displays the last time of cable diagnostics. For example, 'Jan 1 02:03:04 2002'.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.12.1.2.3.2.1.11

Dispalys port utilization during recent 300 seconds.

portUtilEntry row .1.3.6.1.4.1.259.8.1.12.1.2.6.1

Dispalys port utilization during recent 300 seconds.

Indexes

portUtilIfIndex

Column	Syntax	OID
portUtilIfIndex The port and trunk interface of the portUtilTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.1
portInOctetRate The input octet rate (kbits/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.2
portInPacketRate The input packet rate (pkts/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.3
portInUtil The input utilization of the port, in one per hundred.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.4
portOutOctetRate The output octet rate (kbits/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.5
portOutPacketRate The output packet rate (pkts/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.6
portOutUtil The output utilization of the port, in one per hundred.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.6.1.7

Configures vlan trunking feature.

portVlanTrunkingEntry row .1.3.6.1.4.1.259.8.1.12.1.2.7.1

Configures vlan trunking feature.

Indexes

portVlanTrunkingIfIndex

Column	Syntax	OID
portVlanTrunkingIfIndex The port and trunk interface of the portVlanTrunkingTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.2.7.1.1
portVlanTrunkingStatus Whether vlan trunking is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.2.7.1.2

Table describing the configuration and status of each
trunk.

trunkEntry row .1.3.6.1.4.1.259.8.1.12.1.3.3.1

An entry describing the configuration and status of a
particular trunk.

Indexes

trunkIndex

Column	Syntax	OID
trunkIndex Identifies the trunk within the switch that is described by the table entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.3.3.1.1
trunkPorts The complete set of ports currently associated with this trunk.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.12.1.3.3.1.2
trunkCreation A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.	Enumeration Enumerated Values: 1 static 2 lacp	.1.3.6.1.4.1.259.8.1.12.1.3.3.1.3
trunkStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.3.3.1.4

Table for LACP port configuration.

lacpPortEntry row .1.3.6.1.4.1.259.8.1.12.1.4.1.1

Entry for LACP port configuration. While an entry may
exist for a particular port, the port may not support
LACP and an attempt to enable LACP may result in
failure.

Indexes

lacpPortIndex

Column	Syntax	OID
lacpPortIndex The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.4.1.1.1
lacpPortStatus Whether 802.3ad LACP is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.4.1.1.2

The table manages port settings for Spanning Tree
Protocol 802.1d, 802.1w or 802.1s depending on the
value specified by staProtocolType.

staPortEntry row .1.3.6.1.4.1.259.8.1.12.1.5.2.1

The conceptual entry of staPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
staPortFastForward Whether fast forwarding is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.2
staPortProtocolMigration When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.3
staPortOperEdgePort The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.5
staPortAdminPointToPoint The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of f…	Enumerationr/w Enumerated Values: 0 forceTrue 1 forceFalse 2 auto	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.6
staPortOperPointToPoint The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-de…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.7
staPortSystemStatus Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.9
staPortLongAdminPathCost The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This obje…	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.10
staPortLongOperPathCost The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This objec…	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.11
staPortRootGuardAdminStatus Specifies the desired status of the root guard. This variable configures the root guard feature to enforce the root bridge placement in the network.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.13
staPortRootGuardOperStatus The current operational status of the root guard which provides a way to enforce the root bridge placement in the network.	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.14
staPortBpduGuard A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.15
staPortAdminEdgePortWithAuto The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port a…	Enumerationr/w Enumerated Values: 1 true 2 false 3 auto	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.17
staPortBpduFilter The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid trans…	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.18
staPortBpduGuardAutoRecovery A value of enabled(1) indicates that BPDU port guard auto recovery mechanism is enabled for this port. A value of disabled(2) indicates that the mechanism is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.19
staPortBpduGuardAutoRecoveryInterval The interval in seconds used by BPDU guard auto recovery mechanism.	Unsigned32r/w Constraints: range: 30-86400	.1.3.6.1.4.1.259.8.1.12.1.5.2.1.20

This table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0.

xstInstanceCfgEntry row .1.3.6.1.4.1.259.8.1.12.1.5.6.4.1

A conceptual row containing the property of the RST or MST instance.

Indexes

xstInstanceCfgIndex

Column	Syntax	OID
xstInstanceCfgIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.1
xstInstanceCfgPriority The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.	Integer32r/w Constraints: range: 0-61440	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.2
xstInstanceCfgTimeSinceTopologyChange The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.3
xstInstanceCfgTopChanges The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.4
xstInstanceCfgDesignatedRoot The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identi…	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.5
xstInstanceCfgRootCost The cost of the path to the root as seen from this bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.6
xstInstanceCfgRootPort The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.7
xstInstanceCfgMaxAge The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is t…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.8
xstInstanceCfgHelloTime The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.9
xstInstanceCfgHoldTime This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.10
xstInstanceCfgForwardDelay For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the por…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.11
xstInstanceCfgBridgeMaxAge For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the val…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.12
xstInstanceCfgBridgeHelloTime For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.13
xstInstanceCfgBridgeForwardDelay For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.14
xstInstanceCfgTxHoldCount For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.15
xstInstanceCfgPathCostMethod For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value o…	StaPathCostMode Type Values: 1 short 2 long	.1.3.6.1.4.1.259.8.1.12.1.5.6.4.1.16

The extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration.

xstInstancePortEntry row .1.3.6.1.4.1.259.8.1.12.1.5.6.5.1

The conceptual row for xstInstancePortTable.

Indexes

xstInstancePortInstance xstInstancePortPort

Column	Syntax	OID
xstInstancePortInstance The instance of the MSTP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.1
xstInstancePortPort The port and the trunk (excluding trunk member ports) interface of the mstInstancePortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1dStp…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.2
xstInstancePortPriority Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active lin…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.3
xstInstancePortState The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, …	Enumeration Enumerated Values: 1 discarding 2 learning 3 forwarding	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.4
xstInstancePortEnable The enabled/disabled status of the port.	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.5
xstInstancePortPathCost The pathcost of the RST or MST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher val…	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.6
xstInstancePortDesignatedRoot The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.7
xstInstancePortDesignatedCost The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.8
xstInstancePortDesignatedBridge The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.9
xstInstancePortDesignatedPort The port identifier of the port on the designated bridge for this port's segment.	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.10
xstInstancePortForwardTransitions The number of times this port has transitioned from the learning state to the forwarding state.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.11
xstInstancePortPortRole The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port …	Enumeration Enumerated Values: 1 disabled 2 root 3 designated 4 alternate 5 backup 6 master	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.12
xstInstancePortAdminPathCost The admin value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attach…	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.13
xstInstancePortOperPathCost The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attache…	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.12.1.5.6.5.1.14

The Multiple Spanning Tree region instance vlan configuration table.
Please read the actual instance vlan mapped in the mstInstanceOperTable.

mstInstanceEditEntry row .1.3.6.1.4.1.259.8.1.12.1.5.6.6.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceEditIndex

Column	Syntax	OID
mstInstanceEditIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.12.1.5.6.6.1.1
mstInstanceEditVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.6.1.2
mstInstanceEditVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.6.1.3
mstInstanceEditVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.6.1.4
mstInstanceEditVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.6.1.5
mstInstanceEditRemainingHops The remaining hop count for this MST instance.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.5.6.6.1.6

The Multiple Spanning Tree region instance vlan mapped table.

mstInstanceOperEntry row .1.3.6.1.4.1.259.8.1.12.1.5.6.7.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceOperIndex

Column	Syntax	OID
mstInstanceOperIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.12.1.5.6.7.1.1
mstInstanceOperVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.7.1.2
mstInstanceOperVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.7.1.3
mstInstanceOperVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.7.1.4
mstInstanceOperVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.12.1.5.6.7.1.5

A table provides the mechanism to configure the
spanning tree loopback detection of each port or trunk

staLoopbackDetectionPortEntry row .1.3.6.1.4.1.259.8.1.12.1.5.7.1

A conceptual row of staLoopbackDetectionPortTable.

Indexes

staLoopbackDetectionPortIfIndex

Column	Syntax	OID
staLoopbackDetectionPortIfIndex The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.8.1.12.1.5.7.1.1
staLoopbackDetectionPortStatus Status of the port on whether spanning tree loopback detection is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.7.1.2
staLoopbackDetectionPortTrapStatus The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.5.7.1.3
staLoopbackDetectionPortReleaseMode Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manu…	Enumerationr/w Enumerated Values: 1 auto 2 manual	.1.3.6.1.4.1.259.8.1.12.1.5.7.1.4
staLoopbackDetectionPortRelease Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.	Enumerationr/w Enumerated Values: 1 noRelease 2 release	.1.3.6.1.4.1.259.8.1.12.1.5.7.1.5

Table for port mirroring, enabling a port to be mirrored
to/from another port. Not all ports can be mirrored and
limitations may apply as to which ports can be used as either
source or destination ports.

mirrorEntry row .1.3.6.1.4.1.259.8.1.12.1.8.1.1

The conceptual row of mirrorTable.

Indexes

mirrorDestinationPort mirrorSourcePort

Column	Syntax	OID
mirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.8.1.1.1
mirrorSourcePort The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.8.1.1.2
mirrorType If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.	Enumerationr/w Enumerated Values: 1 rx 2 tx 3 both	.1.3.6.1.4.1.259.8.1.12.1.8.1.1.3
mirrorStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.8.1.1.4

Table for VLAN mirroring, enabling a VLAN to be mirrored
to a port.

vlanMirrorEntry row .1.3.6.1.4.1.259.8.1.12.1.8.2.1

The conceptual row of vlanMirrorTable.

Indexes

vlanMirrorDestinationPort vlanMirrorSourceVlan

Column	Syntax	OID
vlanMirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.8.2.1.1
vlanMirrorSourceVlan The source VLAN for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.8.2.1.2
vlanMirrorStatus Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.8.2.1.4

Table for current router ports.

igmpSnoopRouterCurrentEntry row .1.3.6.1.4.1.259.8.1.12.1.9.8.1

Entry for current router ports.

Indexes

igmpSnoopRouterCurrentVlanIndex

Column	Syntax	OID
igmpSnoopRouterCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.8.1.1
igmpSnoopRouterCurrentPorts The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.12.1.9.8.1.2
igmpSnoopRouterCurrentStatus The set of ports which are static router ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.12.1.9.8.1.3

Table for static router ports.

igmpSnoopRouterStaticEntry row .1.3.6.1.4.1.259.8.1.12.1.9.9.1

Entry for static router ports.

Indexes

igmpSnoopRouterStaticVlanIndex

Column	Syntax	OID
igmpSnoopRouterStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.9.1.1
igmpSnoopRouterStaticPorts The set of ports which are static router ports.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.12.1.9.9.1.2
igmpSnoopRouterStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.9.9.1.3

Table for current multicast addresses.

igmpSnoopMulticastCurrentEntry row .1.3.6.1.4.1.259.8.1.12.1.9.10.1

Entry for current multicast addresses.

Indexes

igmpSnoopMulticastCurrentVlanIndex igmpSnoopMulticastCurrentIpAddress

Column	Syntax	OID
igmpSnoopMulticastCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.10.1.1
igmpSnoopMulticastCurrentIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.9.10.1.2
igmpSnoopMulticastCurrentPorts The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.12.1.9.10.1.3
igmpSnoopMulticastCurrentStatus The set of ports which are static members.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.12.1.9.10.1.4

Table for static multicast addresses.

igmpSnoopMulticastStaticEntry row .1.3.6.1.4.1.259.8.1.12.1.9.11.1

Entry for static multicast addresses.

Indexes

igmpSnoopMulticastStaticVlanIndex igmpSnoopMulticastStaticIpAddress

Column	Syntax	OID
igmpSnoopMulticastStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.11.1.1
igmpSnoopMulticastStaticIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.9.11.1.2
igmpSnoopMulticastStaticPorts The set of ports which are members.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.12.1.9.11.1.3
igmpSnoopMulticastStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.9.11.1.4

Table for enabling or disabling IGMP snooping per VLAN.

igmpSnoopCurrentVlanEntry row .1.3.6.1.4.1.259.8.1.12.1.9.14.1

Entry for enabling or disabling IGMP snooping.

Indexes

igmpSnoopCurrentVlanIndex

Column	Syntax	OID
igmpSnoopCurrentVlanIndex Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.14.1.1
igmpSnoopCurrentVlanImmediateLeave The parameter to enable or disable the Immediate-Leave feature on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.9.14.1.3

The table for configuring the IGMP snooping profile.

igmpSnoopProfileEntry row .1.3.6.1.4.1.259.8.1.12.1.9.18.1

The entry for configuring the IGMP snooping profile.

Indexes

igmpSnoopProfileId

Column	Syntax	OID
igmpSnoopProfileId The ID of the IGMP snooping profile.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.18.1.1
igmpSnoopProfileAction The access mode of the IGMP snooping profile.	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.8.1.12.1.9.18.1.2
igmpSnoopProfileStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.9.18.1.3

The table for configuring the range of the IGMP snooping profile.

igmpSnoopProfileRangeEntry row .1.3.6.1.4.1.259.8.1.12.1.9.20.1

The entry for configuring the range of the IGMP snooping profile.

Indexes

igmpSnoopProfileRangeProfileId igmpSnoopProfileRangeInetAddressType igmpSnoopProfileRangeStartInetAddress

Column	Syntax	OID
igmpSnoopProfileRangeProfileId This is defined as igmpSnoopProfileId.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.20.1.1
igmpSnoopProfileRangeInetAddressType The address type is associated with this agent. Only ipv4(1) type is supported.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.259.8.1.12.1.9.20.1.2
igmpSnoopProfileRangeStartInetAddress The specified addresses in the start of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.8.1.12.1.9.20.1.3
igmpSnoopProfileRangeEndInetAddress The specified addresses in the end of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.8.1.12.1.9.20.1.4
igmpSnoopProfileRangeAction The access mode of the IGMP snooping profile.	Enumeration Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.8.1.12.1.9.20.1.5

Table for port configuration in IGMP filtering.

igmpSnoopFilterPortEntry row .1.3.6.1.4.1.259.8.1.12.1.9.21.1

Entry for port configuration in IGMP filtering.

Indexes

igmpSnoopFilterPortIndex

Column	Syntax	OID
igmpSnoopFilterPortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.21.1.1
igmpSnoopFilterPortProfileId The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTab…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.9.21.1.2

Table for port configuration in IGMP throttling.

igmpSnoopThrottlePortEntry row .1.3.6.1.4.1.259.8.1.12.1.9.22.1

Entry for port configuration in IGMP throttling.

Indexes

igmpSnoopThrottlePortIndex

Column	Syntax	OID
igmpSnoopThrottlePortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.9.22.1.1
igmpSnoopThrottlePortRunningStatus Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.12.1.9.22.1.2
igmpSnoopThrottlePortAction The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to th…	Enumerationr/w Enumerated Values: 1 replace 2 deny	.1.3.6.1.4.1.259.8.1.12.1.9.22.1.3
igmpSnoopThrottlePortMaxGroups The maximum number of IGMP groups that the interface can join.	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.259.8.1.12.1.9.22.1.4
igmpSnoopThrottlePortCurrentGroups The current number of IGMP groups that the interface has joined.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.9.22.1.5

A table of netConfigEntry.

netConfigEntry row .1.3.6.1.4.1.259.8.1.12.1.10.1.1

A set of configuration parameters for a particular
network interface on this device. If the device has no network
interface, this table is empty.

The index is composed of the ifIndex assigned to the
corresp…

Indexes

netConfigIfIndex netConfigIPAddress netConfigSubnetMask

Column	Syntax	OID
netConfigIfIndex The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.10.1.1.1
netConfigIPAddress The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.10.1.1.2
netConfigSubnetMask The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure o…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.10.1.1.3
netConfigPrimaryInterface Whether this is a primary interface.	Enumerationr/w Enumerated Values: 1 primary 2 secondary	.1.3.6.1.4.1.259.8.1.12.1.10.1.1.4
netConfigUnnumbered Whether this is an unnumbered interface.	Enumeration Enumerated Values: 1 unnumbered 2 notUnnumbered	.1.3.6.1.4.1.259.8.1.12.1.10.1.1.5
netConfigStatus The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicate…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.12.1.10.1.1.6

Table for DHCP client information listed by interface.
Depending on the nature of the product, this table may
have only one entry(e.g. for the management VLAN), or
may have many entries(e.g. for all ports, or for all
static VLANs).

dhcpcInterfaceEntry row .1.3.6.1.4.1.259.8.1.12.1.10.11.1.1.1.1

Entry for DHCP client information listed by interface.

Indexes

dhcpcIfIndex

Column	Syntax	OID
dhcpcIfIndex This is defined by ifIndex in the IF-MIB.(static vlan if index)	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.10.11.1.1.1.1.1
dhcpcIfClientIdMode Whether the Client ID is in text mode or in Hex mode.	Enumerationr/w Enumerated Values: 1 notSpecify 2 text 3 hex	.1.3.6.1.4.1.259.8.1.12.1.10.11.1.1.1.1.2
dhcpcIfClientId The value that the DHCP client sets in the client_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to uniquely identify the client.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.259.8.1.12.1.10.11.1.1.1.1.3

Table for VLAN configuration.

vlanEntry row .1.3.6.1.4.1.259.8.1.12.1.12.1.1

Entry for VLAN configuration.

Indexes

vlanIndex

Column	Syntax	OID
vlanIndex Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.12.1.12.1.1.1
vlanAddressMethod Method to get the IP address.	Enumerationr/w Enumerated Values: 1 user 2 bootp 3 dhcp	.1.3.6.1.4.1.259.8.1.12.1.12.1.1.2

Table for port configuration in VLAN.

vlanPortEntry row .1.3.6.1.4.1.259.8.1.12.1.12.2.1

Entry for port configuration in VLAN.

Indexes

vlanPortIndex

Column	Syntax	OID
vlanPortIndex The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qPvid in the Q-BRIDG…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.12.2.1.1
vlanPortMode This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link.	Enumerationr/w Enumerated Values: 1 hybrid 2 dot1qTrunk 3 access	.1.3.6.1.4.1.259.8.1.12.1.12.2.1.2
vlanPortPrivateVlanType The port type defined for private VLAN.	Enumerationr/w Enumerated Values: 1 normal 2 isolated 3 community 4 promiscous	.1.3.6.1.4.1.259.8.1.12.1.12.2.1.3

The configuration table which contains the binding entry
of the protocol-group and VLANs.

protocolVlanEntry row .1.3.6.1.4.1.259.8.1.12.1.12.5.1

The binding entry of the protocol-group and VLANs.

Indexes

protocolVlanGroupId

Column	Syntax	OID
protocolVlanGroupId The specified protocol group of a binding entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.12.5.1.1
protocolVlanGroupVid The vlan index of the binding entry. The vid zero is used to delete the binding entry.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.12.5.1.2

A table containing the mac address which can be identified
by voice vlan.

voiceVlanOuiEntry row .1.3.6.1.4.1.259.8.1.12.1.12.6.1.1

A table containing the mac address which can be identified
by voice vlan.

Indexes

voiceVlanOuiAddress

Column	Syntax	OID
voiceVlanOuiAddress MAC address can be identified by voice vlan.		.1.3.6.1.4.1.259.8.1.12.1.12.6.1.1.1
voiceVlanOuiMask The mask of MAC address.	r/w	.1.3.6.1.4.1.259.8.1.12.1.12.6.1.1.2
voiceVlanOuiDescription The description of oui.	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.259.8.1.12.1.12.6.1.1.3
voiceVlanOuiStatus Current operation status of the row.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.12.6.1.1.4

A list of voice vlan mode entries.

voiceVlanPortEntry row .1.3.6.1.4.1.259.8.1.12.1.12.6.7.1

An entry containing voice vlan mode information,
which is applicable to a voice vlan enabled interface.

Indexes

voiceVlanPortIfIndex

Column	Syntax	OID
voiceVlanPortIfIndex The index of interface on which voice vlan function is enabled.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.259.8.1.12.1.12.6.7.1.1
voiceVlanPortMode Voice vlan configuration mode status.	Enumerationr/w Enumerated Values: 1 auto 2 manual 3 none	.1.3.6.1.4.1.259.8.1.12.1.12.6.7.1.2
voiceVlanPortSecurity If the security is enabled, the port is only allow voice traffuc for the voice vlan.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.6.7.1.3
voiceVlanPortPriority The priority of the voice vlan traffic in the port.	Integer32r/w Constraints: range: 0-6	.1.3.6.1.4.1.259.8.1.12.1.12.6.7.1.4
voiceVlanPortRuleOui The address of voice device is learned from Oui table.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.6.7.1.5
voiceVlanPortRuleLldp The address of voice device is learned from LLDP discovery.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.6.7.1.6

Table for port configuration in 802.1Q Tunneling.

vlanDot1qTunnelPortEntry row .1.3.6.1.4.1.259.8.1.12.1.12.8.1

Entry for port configuration in 802.1Q Tunneling.

Indexes

vlanDot1qTunnelPortIndex

Column	Syntax	OID
vlanDot1qTunnelPortIndex The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.12.8.1.1
vlanDot1qTunnelPortMode This variable sets the 802.1Q Tunneling mode. Setting it to none(1) indicates no mode in this port. Setting it to dot1qTunnel(2) sets as dot1q-tunnel mode port which link to customer. Setting it to dot1qTunnelUplink(3) …	Enumerationr/w Enumerated Values: 1 none 2 dot1qTunnel 3 dot1qTunnelUplink	.1.3.6.1.4.1.259.8.1.12.1.12.8.1.2
vlanDot1qTunnelPortEtherType TPID for 802.1Q encapsulation. It's used to select a nonstandard (nondefault) 2-byte ethertype to identify 802.1Q tagged frames.	Unsigned32r/w Constraints: range: 2048-65535	.1.3.6.1.4.1.259.8.1.12.1.12.8.1.3

A table that contains the settings for MAC-based VLAN.

macVlanEntry row .1.3.6.1.4.1.259.8.1.12.1.12.11.1

A conceptual row in the macVlanTable.

Indexes

macVlanMacAddress

Column	Syntax	OID
macVlanMacAddress The MAC address that may specify an entry in the table which contains MAC-based VLAN information.		.1.3.6.1.4.1.259.8.1.12.1.12.11.1.1
macVlanId Specifies the VLAN ID which the MAC address associates with.	Integer32r/w Constraints: range: 1-4092	.1.3.6.1.4.1.259.8.1.12.1.12.11.1.2
macVlanStatus Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.12.11.1.4

A table that contains the settings for IP subnet-based
VLAN.

subnetVlanEntry row .1.3.6.1.4.1.259.8.1.12.1.12.13.1

A conceptual row in the subnetVlanTable.

Indexes

subnetVlanMask subnetVlanIpAddress

Column	Syntax	OID
subnetVlanIpAddress The IPv4 address of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnet…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.12.13.1.1
subnetVlanMask The netmask of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanI…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.12.13.1.2
subnetVlanId Specifies the VLAN ID which the subnet associates with.	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.259.8.1.12.1.12.13.1.3
subnetVlanPriority Specifies the priority whcich the subnet associates with.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.12.1.12.13.1.4
subnetVlanStatus Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.12.13.1.5

Table for port configuration in Layer 2 Protocol
Tunneling.

vlanL2ProtocolTunnelPortEntry row .1.3.6.1.4.1.259.8.1.12.1.12.16.1

Entry for port configuration in Layer 2 Protocol
Tunneling.

Indexes

vlanL2ptPortIndex

Column	Syntax	OID
vlanL2ptPortIndex The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.12.16.1.1
vlanL2ptPortSta Set enabled(1) to enable Layer 2 protocol tunneling for spanning-tree protocol. Set disabled(2) to disable Layer 2 protocol tunneling for spanning-tree protocol.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.16.1.2
vlanL2ptPortLldp Set enabled(1) to enable Layer 2 protocol tunneling for LLDP. Set disabled(2) to disable Layer 2 protocol tunneling for LLDP.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.16.1.3
vlanL2ptPortCdp Set enabled(1) to enable Layer 2 protocol tunneling for Cisco Discovery Protocol. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco Discovery Protocol.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.16.1.4
vlanL2ptPortVtp Set enabled(1) to enable Layer 2 protocol tunneling for Cisco VTP. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco VTP.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.16.1.5
vlanL2ptPortPvst Set enabled(1) to enable Layer 2 protocol tunneling for Cisco PVST+. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco PVST+.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.12.16.1.6

Table for IP DSCP priority mapping.

prioIpDscpEntry row .1.3.6.1.4.1.259.8.1.12.1.13.4.1

Entry for IP DSCP priority mapping.

Indexes

prioIpDscpPort prioIpDscpValue

Column	Syntax	OID
prioIpDscpPort The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.13.4.1.1
prioIpDscpValue Value of IP DSCP as specified in the packet header.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.12.1.13.4.1.2
prioIpDscpCos Class of Service as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The prioIpDscpValue value in the same table row will be mapped to this Class of Service (CoS). This CoS is then further mapped to the hardwar…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.12.1.13.4.1.3

Table for weighted round robin (WRR).

prioWrrEntry row .1.3.6.1.4.1.259.8.1.12.1.13.9.1

Entry for weighted round robin (WRR).

Indexes

prioWrrTrafficClass

Column	Syntax	OID
prioWrrTrafficClass Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.12.1.13.9.1.1
prioWrrWeight Weight for this entry.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.259.8.1.12.1.13.9.1.2

A list of trap destination entries.

trapDestEntry row .1.3.6.1.4.1.259.8.1.12.1.14.1.1

A destination entry describes the destination IP address,
the community string, and SNMP version to use when sending
a trap.

Indexes

trapDestAddress

Column	Syntax	OID
trapDestAddress The address to send traps.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.12.1.14.1.1.1
trapDestCommunity A community to which this destination address belongs.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.259.8.1.12.1.14.1.1.2
trapDestStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.12.1.14.1.1.3
trapDestVersion Determines the version of the trap that is to be sent to the trap receiver. If the value is 1, then an SNMP version 1 trap is sent and if the value is 2, an SNMP version 2 trap is sent.	Enumerationr/w Enumerated Values: 1 version1 2 version2	.1.3.6.1.4.1.259.8.1.12.1.14.1.1.4
trapDestUdpPort Determines the UDP port number that the trap will be sent to.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.12.1.14.1.1.5

Table for rate limit of each port.

rateLimitPortEntry row .1.3.6.1.4.1.259.8.1.12.1.16.1.2.1

Entry for rate limit of each port.

Indexes

rlPortIndex

Column	Syntax	OID
rlPortIndex The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.1.2.1.1
rlPortInputStatus Whether input rate limit is enabled for this port.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.16.1.2.1.6
rlPortOutputStatus Whether output rate limit is enabled for this port.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.12.1.16.1.2.1.7
rlPortInputLimitInKilo Value of the input rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.1.2.1.10
rlPortOutputLimitInKilo Value of the output rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.1.2.1.11

Table for differentiated services on each port.

diffServPortEntry row .1.3.6.1.4.1.259.8.1.12.1.16.4.9.1

Entry for differentiated services on each port.

Indexes

diffServPortIfIndex

Column	Syntax	OID
diffServPortIfIndex This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.9.1.1
diffServPortPolicyMapIndex Specifies the policy map binding to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapEntry as identified by the same value of diffServPolicyMapInd…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.9.1.2
diffServPortIngressIpAclIndex Specifies the ingress IP ACL binding to the interface. The ingress IP ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.9.1.3
diffServPortIngressMacAclIndex Specifies the ingress MAC ACL binding to the interface. The ingress MAC ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.9.1.4
diffServPortIngressIpv6AclIndex Specifies the ingress IPv6 ACL binding to the interface. The ingress IPv6 ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclInd…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.9.1.5

Table for policy map.

diffServPolicyMapEntry row .1.3.6.1.4.1.259.8.1.12.1.16.4.10.1

Entry for policy map.

Indexes

diffServPolicyMapIndex

Column	Syntax	OID
diffServPolicyMapIndex An index that uniquely identifies an entry in this table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.10.1.1
diffServPolicyMapName The name of this entry.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.259.8.1.12.1.16.4.10.1.2
diffServPolicyMapDescription The description of this entry.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.12.1.16.4.10.1.3
diffServPolicyMapElementIndexList The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indicates the diffServPolicyMapEntrys which belong to this entry.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.8.1.12.1.16.4.10.1.4
diffServPolicyMapStatus This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.12.1.16.4.10.1.5

Table for policy map element.

diffServPolicyMapElementEntry row .1.3.6.1.4.1.259.8.1.12.1.16.4.12.1

Entry for policy map element.

Indexes

diffServPolicyMapElementIndex

Column	Syntax	OID
diffServPolicyMapElementIndex An index that uniquely identifies an entry in this table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.12.1.1
diffServPolicyMapElementClassMapIndex Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.12.1.16.4.12.1.2
diffServPolicyMapElementMeterIndex Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identified by the same value of diffServMeterIndex. If this value is …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.12.1.16.4.12.1.3
diffServPolicyMapElementActionIndex Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identified by the same value of diffServActionIndex.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.12.1.16.4.12.1.4
diffServPolicyMapElementStatus This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'acti…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.12.1.16.4.12.1.5