ENTERASYS-IEEE802DOT11EXT-MIB Table View

This table contains objects to test the link between a 
requester (entity which sends out the management request 
message) and a responder (entity which responds with 
the appropriate management response message). An entity
could be either an Access Point(AP) or a station (STA).

etsysDot11ExtLinkTestEntry row .1.3.6.1.4.1.5624.1.2.9.1.1.1.1

An Entry (conceptual row) in the LinkTest Table.
By means of message transmission between requester
and responder, the communication quality between the
two stations can be determined. The requester and
responder ca…

Indexes

No indexes recorded

Column	Syntax	OID
etsysDot11ExtLTRemoteStationMAC The MAC address for the remote station to participate in the Link Test. To initiate a search for a participating station, write the broadcast address (FF-FF-FF-FF-FF-FF) to this variable.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.1
etsysDot11ExtLTRemoteStationName The wireless station name of the remote station participating in the Link Test.	OctetString	.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.2
etsysDot11ExtLTTrigger Writing a 1 to this variable causes a single Link Test request message to be sent to the remote station.	Integer32r/w	.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.3
etsysDot11ExtLTRemoteContents The exact byte-by-byte contents of the Link Test packet returned by the remote station.	OctetString	.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.4

This table contains all the objects that must be 
configured on every radio card installed in the 
Access Point regardless of the operating mode in use.

etsysDot11ExtGeneralEntry row .1.3.6.1.4.1.5624.1.2.9.1.2.1.1

An Entry (conceptual row) in the Dot11General Table.
This allows for multiple instances of radio cards
in the Access Point.

Indexes

No indexes recorded

Column	Syntax	OID
etsysDot11ExtPCCardType The type of PC card inserted in the Access Point.	Enumeration	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.1
etsysDot11ExtPCCardVersions Specifies the version identifiers for the PC card. This will indicate both the Hardware and the Firmware versions.	OctetString	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.2
etsysDot11ExtBridgeMode CURRENT Access Point bridge mode state. In workgroup mode all communications between clients passes through the Access Point. LAN-to-LAN mode is the improved name for 802.11. LAN-to-LA…	Enumerationr/w	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.3
etsysDot11ExtResetOptions noReset (0) No reset is performed. A 'get' on this object always returns this value. resetRadioCardIfNecessary (1) Some parameters can only be given to the card at initialization time, and if any of thes…	Enumerationr/w	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.4
etsysDot11ExtSystemScale Specifies the CURRENT Access Point density in the Extended Service Set (ESS). This object must be saved across a system reset and/or a power cycle.	Enumerationr/w	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.5
etsysDot11ExtSecureAccess When this mode is set to enabled, the AP will only associate with stations that have the same network name as the AP. When this mode is set to disabled, a station with the network name of ANY is allowed to associate. …	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.6
etsysDot11ExtMulticastTxRate This value specifies the Multicast data transmission rate of the AP. It is implemented when cards that operate faster than the 2Mbit 802.11 standard are inserted. This object must be saved across a syste…	Enumerationr/w	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.7
etsysDot11ExtIntraBSSRelay When this mode is enabled the AP entity within the PC Card will relay frames to destined for stations associated with it and will NOT forward them to the bridging entity within the AP. When this mode is set to disabled,…	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.8
etsysDot11ExtStationName DURABLE: The wireless station name sent out as part of the beacon messages. Valid only when a DS card is inserted in the Access Point.	OctetStringr/w	.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.9

This table contains the objects required to enable
the Access Point to operate in Point-to-MultiPoint mode.

etsysDot11ExtBldgEntry row .1.3.6.1.4.1.5624.1.2.9.1.3.1.1

An Entry (conceptual row) in the Dot11Bldg Table.
A collection of objects containing information for activating
and using the Access Point in Point-to-MultiPoint mode.

Indexes

No indexes recorded

Column	Syntax	OID
etsysDot11ExtBldgRemoteMAC1 The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.1
etsysDot11ExtBldgRemoteMAC2 The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.2
etsysDot11ExtBldgRemoteMAC3 The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.3
etsysDot11ExtBldgRemoteMAC4 The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.4
etsysDot11ExtBldgRemoteMAC5 The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.5
etsysDot11ExtBldgRemoteMAC6 The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.6
etsysDot11ExtBldgMPActivationKey Point-to-multipoint bridge mode requires an activation key to enable. A valid multipoint activation key must be entered as a string of ACSCII characters translating to the binary HEX value of the key before the Access …	OctetStringr/w	.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.7

Conceptual table for WEP default keys.  This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values.  The WEP
default secret keys are logically WRITE-ONLY.  Attempts to
read the entries in this table shall return unsuccessful
status and a value of null. The default value of each WEP 
default key shall be null.

etsysDot11ExtWEPDefaultKeysEntry row .1.3.6.1.4.1.5624.1.2.9.1.4.1.1

An Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey.

Indexes

No indexes recorded

Column	Syntax	OID
etsysDot11ExtWEPKeyDefined The state column used for determining if an encryption key is set (true) or not (false), false is the default value.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5624.1.2.9.1.4.1.1.1
etsysDot11ExtWEPKeyValue A WEP default secret key value. For 40-bit encryption use 5 printable characters or 10 HEX digits. For 128-bit encryption use 13 printable characters or 26 HEX digits. This object must be saved across a …	OctetStringr/w	.1.3.6.1.4.1.5624.1.2.9.1.4.1.1.2

Conceptual table for WEP default keys.  This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values.  The WEP
default secret keys are logically WRITE-ONLY.  Attempts to
read the entries in this table shall return unsuccessful
status and a value of null. The default value of each WEP 
default key shall be null.

etsysDot11ExtWEPEnhancedEntry row .1.3.6.1.4.1.5624.1.2.9.1.4.2.1

An Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey.

Indexes

No indexes recorded

Column	Syntax	OID
etsysDot11ExtWEPEnhancedImplemented This value indicates whether the AP is capable of Enhanced Wireless Equivalent Privacy (WEP), using 128-bit keys.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5624.1.2.9.1.4.2.1.1

This table will be used to determine which wireless
parameters have been modified but are not yet in effect.
These parameters will not take effect until a reset has been 
performed.

etsysDot11ExtOIDNotInEffectEntry row .1.3.6.1.4.1.5624.1.2.9.1.5.1.1

Indexes

No indexes recorded

Column	Syntax	OID
etsysDot11ExtOIDIndex This object will keep a list of OIDS	SNMPv2-TCAutonomousType Description: Represents an independently extensible type identification value. It may, for example, indicate a particular sub-tree with further MIB definitions, or define a particular type of protocol or hardware.	.1.3.6.1.4.1.5624.1.2.9.1.5.1.1.1
etsysDot11ExtOIDNotInEffect This object specifies if the OID being accesed currently has been changed but is not in effect.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5624.1.2.9.1.5.1.1.2