ENTERASYS-CONVERGENCE-END-POINT-MIB Table View

This table represents all Convergence End Point types
supported by this entity, and provides a default policy
profile for each Convergence End Point type.

etsysConvEndPointGlobalConfigEntry row .1.3.6.1.4.1.5624.1.2.40.1.1.2.1

Defines the default policy to be applied when this type of
Convergence End Point is detected or discovered.

Indexes

etsysConvEndPointGlobalEndPointType

Column	Syntax	OID
etsysConvEndPointGlobalEndPointType The Convergence End Point type. The value of this object is limited to a single enumerated bit in the ConvEndPointTypes textual convention.	ConvEndPointTypes Type Values: 0 ciscoIPphone 1 siemensIPphone 2 avayaCLan 3 avayaMedPro 4 genericH323 5 sip 6 lldpMed	.1.3.6.1.4.1.5624.1.2.40.1.1.2.1.1
etsysConvEndPointGlobalDefaultPolicyIndex The policy that should be applied for this type of Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index exists, then no policy will b…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.5624.1.2.40.1.1.2.1.2

This table provides control of Convergence End Point detection
and discovery on a per interface and per Convergence End Point
type basis.
          
Maintaining the values of this table across system reboots
is REQUIRED.

etsysConvEndPointProtocolConfigEntry row .1.3.6.1.4.1.5624.1.2.40.1.1.3.1

The current Convergence End Point detection and discovery
status for an interface.

Indexes

IF-MIBifIndex etsysConvEndPointProtocolEndPointType

Column	Syntax	OID
etsysConvEndPointProtocolEndPointType The Convergence End Point type.	ConvEndPointTypes Type Values: 0 ciscoIPphone 1 siemensIPphone 2 avayaCLan 3 avayaMedPro 4 genericH323 5 sip 6 lldpMed	.1.3.6.1.4.1.5624.1.2.40.1.1.3.1.1
etsysConvEndPointProtocolEnable When set to enabled(1), Convergence End Point detection and discovery will be enabled on this interface for the Convergence End Point type specified. When set to disabled(2), the Convergence End Points that have been di…	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5624.1.2.40.1.1.3.1.2

This table provides a mapping from the entities interfaces
to discovered Convergence End Points.
          
Maintaining the value of this object across system reboots
is NOT REQUIRED.

etsysConvEndPointConnPortEntry row .1.3.6.1.4.1.5624.1.2.40.1.2.2.1

Information about an individual Convergence End Point.

Indexes

IF-MIBifIndex etsysConvEndPointConnPortMacAddress

Column	Syntax	OID
etsysConvEndPointConnPortMacAddress The MAC address of the discovered or detected Convergence End Point.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5624.1.2.40.1.2.2.1.1

This table provides information on each of the Convergence
End Points that has been discovered or detected by this
entity.
          
Maintaining the value of this object across system reboots
is NOT REQUIRED.

etsysCEPConnMacEntry row .1.3.6.1.4.1.5624.1.2.40.1.2.3.1

Information about an individual Convergence End Point (CEP).

Indexes

etsysConvEndPointConnPortMacAddress IF-MIBifIndex

Column	Syntax	OID
etsysCEPConnMacEndPointType The type of Convergence End Point described by this row.	ConvEndPointTypes Type Values: 0 ciscoIPphone 1 siemensIPphone 2 avayaCLan 3 avayaMedPro 4 genericH323 5 sip 6 lldpMed	.1.3.6.1.4.1.5624.1.2.40.1.2.3.1.1
etsysCEPConnMacPolicyIndex The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a ze…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.5624.1.2.40.1.2.3.1.2
etsysCEPConnMacDiscoveryTime The time and date that this Convergence End Point was detected or discovered.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.5624.1.2.40.1.2.3.1.3
etsysCEPConnMacFirmwareVersion This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.5624.1.2.40.1.2.3.1.4
etsysCEPConnMacInetAddressType The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.5624.1.2.40.1.2.3.1.5
etsysCEPConnMacInetAddress The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.5624.1.2.40.1.2.3.1.6

A table that describes the IP address and IP port based
Convergence End Point detection parameters.
          
Packets on interfaces that are configured to detect End
Points, via the etsysConvEndPointProtocolConfigTable,
that are defined in this table are inspected to determine
if a Convergence End Point exists on that interface.
          
Rules applying to Convergence End Point types that are
configured for detection are evaluated according to the
following:
          
1.  If etsysConvEndPointDetectionProtocol does not have
    any bits set, this indicates that the port based detection
    should not be performed, proceed to step 2.  Otherwise
    the value in etsysConvEndPointDetectionProtocol is
    evaluated against the protocol field in the IP header,
    if it is of a, or the, type specified then the destination
    port must be between the values of
    etsysConvEndPointDetectionPortLow and
    etsysConvEndPointDetectionPortHigh, inclusive.
          
2.  If the etsysConvEndPointDetectionAddr is null, this 
    indicates that no detection address check should be 
    performed, consider the End Point detected.  Otherwise
    the value the of etsysConvEndPointDetectionAddr will be
    masked with the value of etsysConvEndPointDetectionAddrMask,
    via a bitwise AND operation, and this value will be compared
    with the destination IP address that has also been masked
    with the value of etsysConvEndPointDetectionAddrMask,
    via a bitwise AND operation, if they are equal then
    consider the End Point detected.
          
If there are no rows in this table that are in the active
state then the following pseudo entries describe the
behavior of the IP based Convergence End Point detection.
          
   EndPointType siemens
   Protocol     { { udp, tcp } }
   PortLow      4060
   PortHigh     4060
   AddrType     unknown
   Addr         ''
   AddrMaskType unknown
   AddrMask     ''
          
   EndPointType h323
   Protocol     { { udp, tcp } }
   PortLow      1718
   PortHigh     1720
   AddrType     ipv4
   Addr         '224.0.1.41'
   AddrMaskType ipv4
   AddrMask     '255.255.255.255'
          
   EndPointType sip
   Protocol     { { udp, tcp } }
   PortLow      5060
   PortHigh     5060
   AddrType     ipv4
   Addr         '224.0.1.75'
   AddrMaskType ipv4
   AddrMask     '255.255.255.255'
          
   EndPointType h323
   Protocol     { { udp, tcp } }
   PortLow      1718
   PortHigh     1720
   AddrType     unknown
   Addr         ''
   AddrMaskType unknown
   AddrMask     ''
          
   EndPointType sip
   Protocol     { { udp, tcp } }
   PortLow      5060
   PortHigh     5060
   AddrType     unknown
   Addr         ''
   AddrMaskType unknown
   AddrMask     ''
          
If one or more entries in this table are active the active
entries will define the IP based detection behavior in its
entirety.
          
Maintaining entries in this table across system reboots is 
REQUIRED for entries with an etsysConvEndPointDetectionRowStatus
value of active(1).

etsysConvEndPointDetectionEntry row .1.3.6.1.4.1.5624.1.2.40.1.3.2.1

Each entry represents a describes parameters for
detecting a Convergence End Point.

Indexes

etsysConvEndPointDetectionRuleIndex

Column	Syntax	OID
etsysConvEndPointDetectionRuleIndex The index of this conceptual row. This row represents a single rule for determining if an incoming IP packet indicates the presence of a Convergence End Point device. The lower the numerical value of the index the grea…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.1
etsysConvEndPointDetectionEndPointType The Convergence End Point device type that a 'hit' on this rule will indicate the presence of.	Enumerationr/w Enumerated Values: 0 h323 1 siemens 2 sip	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.2
etsysConvEndPointDetectionProtocol The IP protocol type that the following port range applies to. If no bits are set then the destination port will not be evaluated as part of the detection process.	Bitsr/w Enumerated Values: 0 udp 1 tcp	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.3
etsysConvEndPointDetectionPortLow The low end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the low value in a range of port numbers that will be used to indicate this type of Conver…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.4
etsysConvEndPointDetectionPortHigh The high end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the high value in a range of port numbers that will be used to indicate this type of Conv…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.5
etsysConvEndPointDetectionAddrType The destination address type that will be used for Convergence End Point detection. If the address type is 'unknown', then this value will not be evaluated as part of the detection process.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.6
etsysConvEndPointDetectionAddr The destination IP address that will be used for Convergence End Point detection. If this address is null, then this value will not be evaluated as part of the detection process.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.7
etsysConvEndPointDetectionAddrMaskType The address type of the mask that will be applied to the destination IP address as part of the Convergence End Point detection process. If the address type is 'unknown', then this value will not be evaluated as part of…	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.8
etsysConvEndPointDetectionAddrMask The destination address mask that will be used for Convergence End Point detection. If the mask is null, then this value will not be evaluated as part of the detection process.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.9
etsysConvEndPointDetectionRowStatus The status of this row as defined by the RowStatus textual convention. Rows in this table can only transition to 'notInService', or to 'active' if the etsysConvEndPointDetectionAddrType object and the ets…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.10

A table of per port configuration for Convergence End Point
detection.
          
Maintaining the value of this object across system reboots
is NOT REQUIRED.

etsysCEPDetectionPortConfigEntry row .1.3.6.1.4.1.5624.1.2.40.1.3.3.1

An entry containing per port Convergence End Point data.
Only interfaces that are able to detect Convergence End Points
are represented in this table.

Indexes

IF-MIBifIndex

Column	Syntax	OID
etsysCEPPortClearUsers Setting this object to a value of true(1) will cause all detected or discovered Convergence End Points to be removed from the following status tables: etsysConvEndPointConnMacTable etsysCon…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5624.1.2.40.1.3.3.1.1

A table of per port configuration for Convergence End Point
detection related to the Cisco CDP protocol.  Only ports
that are capable of participating in Cisco CDP protocol are 
represented in this table.

etsysCEPCdpPortConfigEntry row .1.3.6.1.4.1.5624.1.2.40.1.3.4.1

An entry containing per port Convergence End Point data.
Only interfaces that are able to detect Convergence End Points
are represented in this table.

Indexes

IF-MIBifIndex

Column	Syntax	OID
etsysCEPCiscoCDPVoicePortVlan This object controls the behavior of the remote configuration of Cisco VOIP phones via Cisco CDP. Setting this object to a value of -1 will cause the device to not attempt to remotely configure a Cisco phone using CDP…	Integer32r/w Constraints: range: -1-4095	.1.3.6.1.4.1.5624.1.2.40.1.3.4.1.1