ELECTROLINE-DHT-ENET-MIB Table View

Table of Test Controls
Each entry is used to control a test instance.  Tests parameters
shall be inputed to the device first, then the enetTestControl
MIB must be set the setupTest value and Ready status verified before
starting a test.

enetTestControlEntry row .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1

An entry in the Table of Test Control. The will be one entry
per supported simultaneous tests.

Indexes

enetTestIndex

Column	Syntax	OID
enetTestIndex Index for this set of test controls. One set controls one instance of the test engine.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.1
enetTestIdString This String can be used by the management entity as a unique test identifier string. The Enet module will simply copy this string in the result table.	OctetStringr/w	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.2
enetTestControl Used to control the test engine. Once the control parameter for the test are set, the management entity must set this to setupTest(2) & verify that the test control status returns ready before starting the test with …	Enumerationr/w Enumerated Values: 1 stopTest 2 setupTest 3 startTest	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.3
enetTestSenderIP This is the address of the sender entity for the test stream. To set this device as the transmitter for the test, set this MIB to its IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.4
enetTestSenderUDPPort Port Number that the sender will use.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.5
enetTestReceiverIP This is the address of the receiving entity for this test stream. To set this device as the receiver for the test, set this MIB to its IP address. If both enetTestReceiverIP & enetTestSenderIP do not matc…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.6
enetTestReceiverUDPPort UDP port number to be used by the receiving entity. In loopback mode the receiver Port number is also used as both the reception and source port of the loopbacking entity.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.7
enetTestType Sets the type of test to be ran. Selection is made between the following two: voip(1): A VoIP simulation RTP test will be ran, sender will transmit packets simulating a voice codec and the VoIP metrics will be compu…	Enumerationr/w Enumerated Values: 1 voip 2 packetLoss	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.8
enetTestPacketSize Size of the Ethernet packet (Including headers) to be used by this test. Note that the packet size for rtp test is computed from the packet interval and the codec type. This MIB is used for packetLoss …	Integer32r/w Constraints: range: 64-1514	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.9
enetTestPacketInterval Interval in milliseconds between each packets. This parameter is used only for the RTP test type.	Integer32r/w Constraints: range: 10-10 range: 20-20 range: 30-30	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.10
enetTestPacketRate Number of packets per seconds to be transmitted. This parameter is used only for packetLoss test type.	Integer32r/w Constraints: range: 0-255000	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.11
enetTestNumOfPackets Maximum duration of the test expressed in number of packets. A sender will stop the transmitting when it reaches this amount. A receiver can use this parameter to know how many packets to expect. The …	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.12
enetTestJitterBufferSize Jitter buffer size in millisecond to be implemented by the receiving entity. This will impact the total delay and the discarded packet count. The value set in this MIB must be a multiple of 20 millisecon…	Integer32r/w Constraints: range: 0-200	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.13
enetTestQosControl This parameter tells the DHT is a specific service flow must be used for the test. none(1): Means that the test will run in a best effort mode. preestablished(2): tells the DHT that a high …	Enumerationr/w Enumerated Values: 1 none 2 preestablished 3 dsa	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.14
enetTestCodecType The Codec type to be used for the rtp test. It is used by sender to set the appropriate value in the rtp header. The receiver can use this parameter in the computation of the R-Factor. Th…	Enumerationr/w Enumerated Values: 0 na 1 g711	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.15
enetTestTosByte Type of Service Byte to be used in the transmitted packets. This parameter is used only for the rtp test type.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.16
enetTestRoundTripTimeEstimate The round trip time (in milliseconds) is used by the DHT in the computation of the CQE R-Factor. It must be estimated by the management entity and supplied to the DHT via the use of this MIB for the RCQE result to be …	Integer32r/w Constraints: range: 0-60000	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.17
enetTestStatus This MIB indicates the test status. A value of N/A(0) is returned before the test is ran. A value of Running (1) is returned while the test is in progress. A value of Completed (2) is returned when the test is stoppe…	Enumeration Enumerated Values: 0 na 1 running 2 completed 3 ressourceUnavailable 4 invalidParameter 5 ready	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.18
enetTestStatusString This field is used by the device to further explain the Status of the test. and its content is device specific.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.19

Table that contains the current cummulative test results. 
This table is used for both packetLoss and RTP test types
but some values are valid only for the RTP tests.  
The result values are reset each time the test is started.
          
Note that all the results for one entry are updated at once 
when a get on the enetResultsStatus is performed.  This ensures
that all displayed results where taken in the same period and
are coherent with each other.

enetCurrentResultsEntry row .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1

An entry in the result table. Each simultaneous test has its own
entry. The index of the enetResultsEntry will match that of the
EnetTestControlEntry.

Indexes

enetResultsIndex

Column	Syntax	OID
enetResultsIndex Index for this set of data.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.1
enetResultsIdString A copy of the corresponding enetTestIdString string.	OctetString	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.2
enetResultsStatus This MIB shows the result status. A value of partial(1) is returned while the test is running. A value of complete(2) is returned if the test is stopped. The inconsistent(0)…	Enumeration Enumerated Values: 0 inconsistent 1 partial 2 complete	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.3
enetResultsDuration Total Duration of the test in milliseconds.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.4
enetResultsStartTime System time at the beginning of the test.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.5
enetResultsStopTime System time at the end of the test. The value of this MIB is valid only if the enetResultsStatus is complete(2)	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.6
enetResultsProcessedPacketCount Total number of packets that have been processed by the device. In transmission this indicates the number of packets sent In reception this is the sum of the good packets and the discarded packets.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.7
enetResultsLossPacketCount Number of packets lost in the network before their arrival to this device. The value reported by this MIB is valid only in the receiving end-point.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.8
enetResultsDiscardedPacketCount Number of packets discarded by this device because they arrived too late to be played out by the codec. The value reported by this MIB is valid only in the receiving end-point.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.9
enetResultsPacketLossRate Lost packets over total number of expected packets expressed in percent. The value reported by this MIB is valid only in the receiving end-point.	ScaledPercentage Type Constraints: range: 0..1000	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.10
enetResultsPacketDiscardRate Discarded packets over total number of expected packets expressed in percent. The value reported by this MIB is valid only in the receiving end-point.	ScaledPercentage Type Constraints: range: 0..1000	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.11
enetResultsMinInstantJitter Minimum value of the Inter packet delay variation. The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.12
enetResultsMaxInstantJitter Maximum value of the Inter packet delay variation. The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.13
enetResultsAvgInstantJitter Average value of the Inter packet delay variation. The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.14
enetResultsMinRfcJitterLevel Mimimum of the smoothed Jitter level computed as per rfc3550. The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.15
enetResultsMaxRfcJitterLevel Maximum of the smoothed Jitter level computed as per rfc3550. The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.16
enetResultsAvgRfcJitterLevel Average of the smoothed Jitter level computed as per rfc3550. The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.17
enetResultsRCQ Computed R-Factor - Conversationnal Quality Equivalent as per ITU G.107 The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	Rfactor Type Constraints: range: 0..120 range: 127	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.18
enetResultsRLQ Computed R-Factor - Listening Quality Equivalent as per ITU G.107 The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	Rfactor Type Constraints: range: 0..120 range: 127	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.19
enetResultsMOSCQ Computed MOS - Conversationnal Quality Equivalent as per ITU G.107 The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	ScaledMOSscore Type Constraints: range: 10..50 range: 127	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.20
enetResultsMOSLQ Computed MOS - Listenning Quality Equivalent as per ITU G.107 The value reported by this MIB is valid only in the receiving end-point. of an RTP test.	ScaledMOSscore Type Constraints: range: 10..50 range: 127	.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.3.1.1.21