Dell-LAN-SYSMNG-MIB Table View

This table defines all management ACL rule-set as well as the rules
within the rule-set.  To activate a specific ACL rule-set, please 
refer to the 'dellLanMngInfActiveListName' parameter above.

dellLanMngInfListEntry row .1.3.6.1.4.1.674.10895.5000.1.2.1.3.1

Each entry in the table is a single rule within a given rule-set.
The rules within a rule-set are grouped together via a common
name 'dellLanMngInfListName'. Each rule has a specific priority
within the rule-set given …

Indexes

dellLanMngInfListName dellLanMngInfListPriority

Column	Syntax	OID
dellLanMngInfListName The name of a given rule-set.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.1
dellLanMngInfListPriority The priority value of a given rule within the rule-set.	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.2
dellLanMngInfListIfIndex The IfIndex to which this rule applies. By setting this to a specific ifIndex, the rule will only applies if the management access is coming over the given interface. If the ifIndex is set to 0, then this rule applies…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.3
dellLanMngInfListIpAddr The IP address to which this rule applies. The IP address may be set to be 0, which means that the rule applies to all IP addresses. Otherwise, the rule applies to all management request which comes from a given IP add…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.4
dellLanMngInfListIpNetMask The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0. Using this in conjunction with the ipAddress gi…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.5
dellLanMngInfListService The type of services that this rule applies to. By setting this to a specific service type, the rule will only apply if the request is coming to the switch using the particular protocol type specified. The Service typ…	DellLanMngInfServiceTyper/w Type Values: 0 allType 1 telnet 2 snmp 3 http 4 https 5 ssh 6 sntp	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.6
dellLanMngInfListAction The action to apply to the given traffic matching the rule. The action may be to permit or deny the requested management access.	DellLanMngInfActionTyper/w Type Values: 0 permit 1 deny	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.7
dellLanMngInfListRowStatus The row status variable, used according to row creation and deletion conventions.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.8
dellLanMngInfListVlanId The IfIndex to which this rule applies. By setting this to a specific ifIndex, the rule will only applies if the management access is coming over the given interface. If the ifIndex is set to 0, then this rule applies…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.674.10895.5000.1.2.1.3.1.9

This table 'lists' the files that are present in the flash file
system of the switch.

dellLanFileEntry row .1.3.6.1.4.1.674.10895.5000.1.2.2.3.1

Each entry is a single file in the file system. Each file has
particular access permission. This table provides the mean to
view a files in the file system. A file cannot be created or
deleted using this table. To c…

Indexes

dellLanFileName

Column	Syntax	OID
dellLanFileName The name of the file.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.1
dellLanFilePermission Specifies the permission level in which this file can be accessed.	Enumeration Enumerated Values: 1 readonly 2 writeonly 3 readWrite 4 noReadNoWrite	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.2
dellLanFilePriority This special priority level is applicable only when the file is an image. Setting this priority level on the image file identifies the order in which the system will choose a new image to load when it finds the active …	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.3
dellLanFileSize The size of the file in bytes.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.4
dellLanFileType The type of file.	Enumeration Enumerated Values: 1 image 2 config 3 log 4 sys 5 activeImg	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.5
dellLanFileModificationDate The time-stamp indicating the date of creation or last modification of this file. The format of the time-stamp is dd-mmm-yyyy	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.6
dellLanFileModificationTime The time-stamp indicating the time of creation or last modification of this file. The format of the time-stamp is hh:mm:ss	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.7
dellLanFileDescription A user defined description associated with this file. By default there is no description.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.674.10895.5000.1.2.2.3.1.8

This is a conceptual table which contain only one row.  The
row is used to setup the parameters required to execute a
particular action on the file system.  Depending on the action,
certain number of parameters will apply and will be required
to be configured when the action is executed.  Once the action
executes, the parameters set for the action will be cleared and
the status of the action (error code or success code) will be
available for query in the dellLanFileActionResultCode field.
          
NOTE that since the action is immediately executed, all parameters
required for the action must be given in the same SNMP set request
in a single varbind.  The action type dellLanFileActionCommand
must be included in each SNMP set request otherwise an error will
be returned.
          
Some of the actions may take a long time to complete, for these
actions, the user should poll the dellLanFileActionResultCode
until a valid result is returned.  When the system is working on
an action this parameter will return 'statusPending'.  While the
status is 'statusPending' the system will not honor any new
file system request.  If the user tries to send a file system 
action request during this time, the SNMP SET to execute the
action will return with an SNMP error and the status will remain
'statusPending' until the last operation has completed.
          
The correct usage for this table should be:
- first query the 'dellLanFileActionResultCode' to see if the
  system is free to execute a file action request.  If the 
  query returns 'statusPending' then don't try the action yet.
  Keep polling until the result of this parameter is something
  other then 'statusPending'.
- once the system is ready, compose a single SNMP request with
  all parameters required for a given action (see the description
  below in the Entry definition).
- send an SNMP SET for this request, if the SET failed with an
  SNMP error then something is wrong with the way the request is
  composed.
- if the SNMP SET response is success, then start polling the
  dellLanFileActionResultCode to determine the status of the
  action.

dellLanFileActionEntry row .1.3.6.1.4.1.674.10895.5000.1.2.2.4.1

There is only exactly one row in this table and the row index is
always set to 1 (dellLanFileActionIndex = 1). When an action is
required to manipulate the file system, the entire action must
be sent in the same SNMP S…

Indexes

dellLanFileActionIndex

Column	Syntax	OID
dellLanFileActionIndex This parameter is always 1 since this table consists of always just one row.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.674.10895.5000.1.2.2.4.1.1
dellLanFileActionSourceFile The source file may be specified using a URL addressing scheme. The format of this address are as follows: - flash://filename => indicate a file on the flash file system. - filename …	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.674.10895.5000.1.2.2.4.1.2
dellLanFileActionDestFile The destination file may be specified using a URL addressing scheme. The format of this address are as follows: - flash://filename => indicate a file on the flash file system. - file…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.674.10895.5000.1.2.2.4.1.3
dellLanFileActionForceAction This option indicate that the system should force the operation if possible. For example, if this is used with the copy command, then the system will try to overwrite the destination file if it already exists. The ove…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.674.10895.5000.1.2.2.4.1.4
dellLanFileActionCommand Perform the specific action on the file. When the action is performed the set of required parameters (see description in the table & entry definition above) must be included in the same varbind as the action. If the a…	Enumerationr/w Enumerated Values: 2 copy 3 delete	.1.3.6.1.4.1.674.10895.5000.1.2.2.4.1.5
dellLanFileActionResultCode Each time the action is attempted, the result of the action will be provided here. The user should always read this result code immediately after executing the action to check the status of the action. If the action t…	Enumeration Enumerated Values: 0 success 1 statusPending 2 fileNotFound 3 invalidCmd 4 unknownError 5 tftpServerConnectFailed 6 fileSystemFull 7 overwriteNotRequested 8 overwriteFailed 9 permissionDenied 10 incompatFileType 11 invalidDest	.1.3.6.1.4.1.674.10895.5000.1.2.2.4.1.6