DLINK-DXS-1210-16TC-AX-MIB Table View

The table of Firmware Information.

firmwareInformationEntry row .1.3.6.1.4.1.171.10.139.4.1.1.1.2.1.1

The list ofFirmware Information entry.

Indexes

firmwareInfoImageID

Column	Syntax	OID
firmwareInfoImageID Firmware Information. Image ID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.1.1.2
firmwareInfoVersion Firmware Information. Version.	OctetString Constraints: range: 1-20	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.1.1.3
firmwareInfoSizeB Firmware Information. Size B.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.1.1.4
firmwareInfoUpdateTime Firmware Information. Update Time.	OctetString Constraints: range: 1-20	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.1.1.5

A list of configuration entries.

devFunCfgInfoEntry row .1.3.6.1.4.1.171.10.139.4.1.1.1.2.3.1.1

A list of configuration entries.

Indexes

devFunCfgId

Column	Syntax	OID
devFunCfgId A unique value, greater than zero, for each configuration id.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.3.1.1.1
devFunCfgSize The configuration file size by id.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.3.1.1.2
devFunCfgUpdateTime The configuration last update time by id.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.3.1.1.3

Defines a table for storing the results of ping
operations.  The number of entries in this table is
limited per entry  by the value of the corresponding 
PingProbeMaxRow object.
          
An implementation of this MIB will remove the oldest
entry of the corresponding entry in the PingProbeMaxRow 
to allow the addition of an new entry once the number of rows
reaches the value specified by pingCtlMaxRows for the 
corresponding entry in the PingProbeMaxRow.

devPingProbeHistoryEntry row .1.3.6.1.4.1.171.10.139.4.1.1.1.2.6.9.1

Defines an entry in the PingProbeHistoryTable.
The index element selects a single probe result.

Indexes

devPingProbeIndex

Column	Syntax	OID
devPingProbeIndex The probe history sequence of this entry belong to	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.6.9.1.1
devPingProbeHistoryResponseTime The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.1.1.2.6.9.1.2

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

deviceErrorCodeEntry row .1.3.6.1.4.1.171.10.139.4.1.1.1.3.1.1

An entry appears in this table for each interface in the system.
Index to the table is the interface index of the port.

Indexes

devErrorCodeIndex

Column	Syntax	OID
devErrorCodeIndex Error code index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.1.1.3.1.1.1
devErrorString The error string of the index.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.1.1.3.1.1.2

A table consists of a list of Fan status.

environmentFanEntry row .1.3.6.1.4.1.171.10.139.4.1.2.2.4.1

An entry defines information for fan status.

Indexes

environmentFanId

Column	Syntax	OID
environmentFanId the fan id .	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.2.2.4.1.2
environmentFanStatus This object indicates the status of fan.	Enumeration Enumerated Values: 1 ok 2 fail	.1.3.6.1.4.1.171.10.139.4.1.2.2.4.1.3
environmentFanSpeed This object indicates the speed of fan.	Enumeration Enumerated Values: 0 down 1 low 2 high	.1.3.6.1.4.1.171.10.139.4.1.2.2.4.1.4

A table consists of a list of SYSLOG servers to log system messages
and debug output to a remote SYSLOG server host.

syslogServerEntry row .1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1

An entry defines information for a SYSLOG server.

Indexes

syslogServerIndex

Column	Syntax	OID
syslogServerIndex the server config entry index.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.1
syslogServerAddressType This object indicates the type of the server address.	Enumerationr/w Enumerated Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.2
syslogServerAddress This object indicates the IP or IPv6 address of the SYSLOG server.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.3
syslogServerPort This object indicates the UDP port number to be used for the SYSLOG server.	Integer32r/w Constraints: range: 514-514 range: 1024-65535	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.4
syslogServerSeverity This object indicates the severity of log messages that will be sent to the server.	Enumerationr/w Enumerated Values: 0 emergencie 1 alerts 2 critical 3 error 4 warning 5 notification 6 informational 7 debugging	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.5
syslogServerFacility Specifies the logging facility of the log host.	Enumerationr/w Enumerated Values: 0 kern 1 user 2 mail 3 daemon 4 auth 5 syslog 6 lpr 7 news 8 uucp 9 cron 10 authpriv 11 ftp 12 ntp 13 audit 14 console 15 cron2 16 local0 17 local1 18 local2 19 local3 20 local4 21 local5 22 local6 23 local7	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.6
syslogServerRowstatus The row status variable, used according to installation and removal conventions for conceptual rows.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.5.1.7

A table consists of a list of system log messages.

syslogBufferEntry row .1.3.6.1.4.1.171.10.139.4.1.2.4.1.7.1

An entry defines a log message.

Indexes

syslogBufferIndex

Column	Syntax	OID
syslogBufferIndex An index that uniquely identifies the message.	Unsigned32 Constraints: range: 1-100000	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.7.1.1
syslogBufferDateAndTime The date and time when the message is logged.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.7.1.2
syslogBufferDescription The content of the log message.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.7.1.3
syslogBufferSeverity This object indicates the severity of log messages that will be sent to the server.	Enumeration Enumerated Values: 0 emergencie 1 alerts 2 critical 3 error 4 warning 5 notification 6 informational 7 debugging	.1.3.6.1.4.1.171.10.139.4.1.2.4.1.7.1.4

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

portCtrlEntry row .1.3.6.1.4.1.171.10.139.4.1.2.13.1.1

An entry appears in this table for each interface in the system.
Index to the table is the interface index of the port.

Indexes

portSetIndex portSetMediaType

Column	Syntax	OID
portSetIndex Interface index of the port for the configuration in this entry applies.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.1
portSetMediaType Media Type.	Enumeration Enumerated Values: 1 copper 2 fiber	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.2
portSetState Enables / disables Port state.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.3
portSetFlowControl On / off flow control for the interface.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.4
portSetDuplex Configures port settings auto/half/full mode.	Enumerationr/w Enumerated Values: 1 auto 2 full	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.5
portSetSpeed Configures port settings speed.	Enumerationr/w Enumerated Values: 1 auto 2 rate100M 3 rate1000M 6 rate10G	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.6
portSetCapaAdvertised Configures port settings interface capability advertised 100M/1000M/10G .	Enumerationr/w Enumerated Values: 1 adv100M 2 adv1G 3 adv100M-1G 4 adv10G 5 adv100M-10G 6 adv1G-10G 7 adv100M-1G-10G	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.7
portSetDescription Configures port settings Description.	OctetStringr/w Constraints: range: 1-64	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.8
portSetLinkStatus Show port settings LinkStatus up /down.	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.171.10.139.4.1.2.13.1.1.9

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

portStatusEntry row .1.3.6.1.4.1.171.10.139.4.1.2.13.2.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

portStaIndex portStaMediaType

Column	Syntax	OID
portStaIndex Interface index of the port for the configuration in this entry applies.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.1
portStaMediaType Media Type.	Enumeration Enumerated Values: 1 copper 2 fiber	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.2
portStaStatus Show port status Link Status up /down.	Enumeration Enumerated Values: 1 connected 2 notconnected	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.3
portStaMacAddr Show port status MAC Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.4
portStaVlan The VLAN-ID assigned to untagged frames received on this port. The port in native VLAN will also been set as untagged as default setting.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.5
portStaFlowCtrlOpSend On / off flow control Operator Send for the interface.	Enumeration Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.6
portStaFlowCtrlOpRece On / off flow control Operator Receive for the interface.	Enumeration Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.7
portStaDuplex Show port Status Duplex auto/full mode.	Enumeration Enumerated Values: 1 auto 2 full 3 auto-full 4 auto-falf	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.8
portStaSpeed Show port Status speed.	Enumeration Enumerated Values: 1 auto 2 rate100M 3 rate1000M 6 rate10G 7 auto-rate100M 8 auto-rate1000M 9 auto-rate10G	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.9
portStaType Show port Status Type.	Enumeration Enumerated Values: 1 rate10GBase-T 2 rate10GBase-R	.1.3.6.1.4.1.171.10.139.4.1.2.13.2.1.10

The Port Error Disable table.

errDisIfStatusEntry row .1.3.6.1.4.1.171.10.139.4.1.2.13.6.1

A list of information for the err port of the device.

Indexes

errDisIfStatusPortIndex errDisIfStatusVlanIndex

Column	Syntax	OID
errDisIfStatusPortIndex This object is the interface index of the interface disabled by a feature.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.139.4.1.2.13.6.1.1
errDisIfStatusVlanIndex This object indicates the VLAN in the given interface that has been error-disabled.('0'is on behalf of 'port base mode')	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.171.10.139.4.1.2.13.6.1.2
errDisPortState This object decides whether the port state is enabled or disabled.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.139.4.1.2.13.6.1.3
errDisPortConnectStatus This object decides whether the PortStatus is err-disabled.	Enumeration Enumerated Values: 1 other 2 err-disabled	.1.3.6.1.4.1.171.10.139.4.1.2.13.6.1.4
errDisPortReason This object indicats the reason for Port Error Disable event occur.	Enumeration Enumerated Values: 1 portsecurity 2 stormControl 3 arpRateLimit 4 bpduRateLimit 5 dhcpRateLimit 6 loopbackDetect	.1.3.6.1.4.1.171.10.139.4.1.2.13.6.1.5
errDisPortRecoveryTimeLeft This object indicats the remaining time for Port Error Disable state recovery.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.2.13.6.1.6

This table contains the recovery mechanism for the features with 
error-disable functionality.

errDisRecoveryEntry row .1.3.6.1.4.1.171.10.139.4.1.2.13.7.1

An entry is created for each feature which has error-disable
functionality.

Indexes

errDisRecoveryReason

Column	Syntax	OID
errDisRecoveryReason This object indicates the cause of error-disable.	Enumeration Enumerated Values: 1 portsecurity 2 stormControl 3 arpRateLimit 4 bpduRateLimit 5 dhcpRateLimit 6 loopbackDetect	.1.3.6.1.4.1.171.10.139.4.1.2.13.7.1.1
errDisRecoveryStatus This object specifies whether the system can automatically recover a system entity that has been disabled by the cause.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.139.4.1.2.13.7.1.2
errDisRecoveryInterval Specifies the error-recovery time interval on specific cause to recover the port/interface from the error disabled situation.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.2.13.7.1.3

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

jumboFrameEntry row .1.3.6.1.4.1.171.10.139.4.1.2.13.14.1

An entry appears in this table for each interface in the system.
Index to the table is the interface index of the port.

Indexes

portIndex

Column	Syntax	OID
portIndex Interface index of the port for the configuration in this entry applies.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.139.4.1.2.13.14.1.1
maxReceFrameSize Interface index of the port for the configuration in this entry applies.	Integer32r/w Constraints: range: 1518-9216	.1.3.6.1.4.1.171.10.139.4.1.2.13.14.1.2

The table contains configured SNTP/NTP servers in the system.

sntpServerEntry row .1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1

Each entry in the table contains necessary information to
send SNTP request to the servers.

Indexes

sntpServerAddrType sntpServerAddr

Column	Syntax	OID
sntpServerAddrType The IP address type ipv4 or ipv6.	Enumeration Enumerated Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.1
sntpServerAddr The unicast IPv4/IPv6 server address in the Unicast Addressing mode	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.2
sntpServerStratum stratum levels define the distance from the reference clock.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.3
sntpServerVersion sntp server version.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.4
sntpServerLastReceive The value of sysUpTime when this server was synced.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.5
sntpServerSynced This object indicates whether the corresponding server is the current synced server.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.6
sntpServerRowStatus The activation of a row adds server entry. The destruction of a row removes server entry	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.2.17.3.3.1.7

A table to configure time Range in the system.

timeRangeEntry row .1.3.6.1.4.1.171.10.139.4.1.2.38.1.1

A schedule entry to configure time Range in the system.

Indexes

timeRangeName timeRangeIndex

Column	Syntax	OID
timeRangeName The Schedule name associated with the Schedule entry (e.g., `abc, bbb').	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.1
timeRangeIndex The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.2
timeRangeStartHour Start hour of the Schedule entry. The value must be from 0 to 23.	Integer32r/w Constraints: range: 0-23	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.3
timeRangeStartMinute Start minute of the Schedule entry. The value must be from 0 to 59.	Integer32r/w Constraints: range: 0-59	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.4
timeRangeEndHour End hour of the Schedule entry. The value must be from 0 to 23.	Integer32r/w Constraints: range: 0-23	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.5
timeRangeEndMinute End minute of the Schedule entry. The value must be from 0 to 59.	Integer32r/w Constraints: range: 0-59	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.6
timeRangeWeekday Enable/Disble scheduling weekday list.	Bitsr/w Enumerated Values: 0 saturday 1 friday 2 thursday 3 wednesday 4 tuesday 5 monday 6 sunday	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.7
timeRangeRowStatus The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are available.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.8
timeRangeDaily The flag represent for whether the timerange is daily or not.	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.171.10.139.4.1.2.38.1.1.9

A table to User Accounts Settings. User Management Settings.

userAccountsEntry row .1.3.6.1.4.1.171.10.139.4.1.3.1.1.1.1

An entry appears in User Accounts Settings. User Management Settings.

Indexes

userName

Column	Syntax	OID
userName The name of user entry.	OctetString Constraints: range: 1-15	.1.3.6.1.4.1.171.10.139.4.1.3.1.1.1.1.1
userPrivilege User Management Settings. Privilege (1-15)	Unsigned32r/w Constraints: range: 1-15	.1.3.6.1.4.1.171.10.139.4.1.3.1.1.1.1.2
userEncryptControl The Encrypt algorithm of user password.	Enumerationr/w Enumerated Values: 0 none 1 plaintext 2 encrypted-sha1 3 encrypted-md5	.1.3.6.1.4.1.171.10.139.4.1.3.1.1.1.1.3
userPassword The password of user entry. 0 means no password.	OctetStringr/w Constraints: range: 0-15	.1.3.6.1.4.1.171.10.139.4.1.3.1.1.1.1.4
userRowStatus Row Status of user Accounts Entry.(can not set to notinservice(2) and notready(3))	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.3.1.1.1.1.5

A Session Table contain the user login information.

userSessionEntry row .1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1

A Session Table contain the user login information.

Indexes

sessionID

Column	Syntax	OID
sessionID The index of session table.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1.1
liveTime The time peroid user has kept login.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1.2
loginType login client of http, telnet, ssh or console.	Enumeration Enumerated Values: 1 http 2 telnet 3 ssh 4 console	.1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1.3
loginIP login ip through http, ssh, or telnet.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1.4
loginUserLevel The level of session which user login.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1.5
loginUserName The name of login user.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.3.1.2.1.1.6

The table of snmp view tree.

snmpViewEntry row .1.3.6.1.4.1.171.10.139.4.1.3.3.3.1.1

The list of snmp view tree entry.

Indexes

snmpViewName snmpViewSubtree

Column	Syntax	OID
snmpViewName The human readable name for a family of view subtrees.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.3.1.1.1
snmpViewSubtree The MIB subtree which when combined with the corresponding instance of vacmViewFamilyMask defines a family of view subtrees.	ObjectIdentifier	.1.3.6.1.4.1.171.10.139.4.1.3.3.3.1.1.2
snmpViewType Indicates whether the corresponding instances of vacmViewFamilySubtree and vacmViewFamilyMask define a family of view subtrees which is included in or excluded from the MIB view.	Enumerationr/w Enumerated Values: 1 included 2 excluded	.1.3.6.1.4.1.171.10.139.4.1.3.3.3.1.1.3
snmpViewStatus The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.3.3.3.1.1.4

The table of snmp community.

snmpCommunityEntry row .1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1

The list of snmp community entry.

Indexes

snmpCommName

Column	Syntax	OID
snmpCommName The unique index value of a row in this table.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1.1
snmpCommKeyType Key Type.	Enumerationr/w Enumerated Values: 1 plainText 2 encrypted	.1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1.2
snmpCommViewName SNMP Community Settings View Name.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1.3
snmpCommAccessRight SNMP Community Settings Key Type.	Enumerationr/w Enumerated Values: 1 readOnly 2 readWrite	.1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1.4
snmpCommIPAccListName SNMP Community Settings IP Access-List Name.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1.5
snmpCommStatus The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through defau…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.3.3.4.1.1.6

The table of snmp group.

snmpGroupEntry row .1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1

The list of snmp group entry.

Indexes

snmpGroupName snmpGroupSecurityModel snmpGroupSecurityLevel

Column	Syntax	OID
snmpGroupName The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. Ho…	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.1
snmpGroupSecurityModel In order to gain the access rights allowed by this conceptual row, this securityModel must be in use.	Enumeration Enumerated Values: 1 v1 2 v2c 3 v3	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.2
snmpGroupSecurityLevel The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If m…	Enumeration Enumerated Values: 1 noAuthNoPriv 2 authNoPriv 3 authPriv	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.3
snmpGroupReadViewName The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamil…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.4
snmpGroupWriteViewName The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFami…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.5
snmpGroupNotifyViewName The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacm…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.6
snmpGroupIpListName SNMP Group Settings IP Address-List Name.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.7
snmpGroupStatus The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.3.3.5.1.1.8

The table of snmp user.

snmpUserEntry row .1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1

The list of snmp user entry.

Indexes

snmpUserName snmpUserVersion

Column	Syntax	OID
snmpUserName A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.1
snmpUserVersion A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.	Enumeration Enumerated Values: 1 v1 2 v2c 3 v3	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.2
snmpUserGroupName The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. Ho…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.3
snmpUserV3Encrypt A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.	Enumerationr/w Enumerated Values: 0 none 1 password 2 key	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.4
snmpUserAuthProtocol An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An …	Enumerationr/w Enumerated Values: 1 none 2 md5 3 sha	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.5
snmpUserAuthProtocolPassword Password of snmp user auth protocol.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.6
snmpUserPrivProtocol An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. …	Enumerationr/w Enumerated Values: 1 none 2 des	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.7
snmpUserPrivProtocolPassword Password of snmp user priv protocol.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.8
snmpUserAuthProtoByKey Auth-Protocol by Key.	Enumerationr/w Enumerated Values: 1 none 2 md5 3 sha	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.9
snmpUserAuthProtoKey Key of snmp user auth protocol by Key.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.10
snmpUserPrivProtoByKey Priv-Protocol by Key.	Enumerationr/w Enumerated Values: 1 none 2 des	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.11
snmpUserPrivProtoKey Key of snmp user Priv protocol by Key.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.12
snmpUserIpListName SNMP User Settings IP Address-List Name.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.13
snmpUserStatus The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.3.3.7.1.1.14

The table of snmp host.

snmpHostEntry row .1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1

The list of snmp host entry.

Indexes

snmpHostAddress snmpHostIPType

Column	Syntax	OID
snmpHostAddress This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1.1
snmpHostIPType Type of IP interface.	Enumeration Enumerated Values: 1 iPv4 2 iPv6	.1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1.2
snmpHostVersion The Level of Security to be used when generating SNMP messages using this entry.	Enumerationr/w Enumerated Values: 1 v1 2 v2c 3 noAuthNoPriv 4 authNoPriv 5 authPriv	.1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1.3
snmpHostUDPPort SNMP UDP Port (1-65535).	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1.4
snmpHostCommunityName The locally arbitrary.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1.5
snmpHostStatus The status of this conceptual row in the snmpHostTable.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.3.3.8.1.1.6

A list of Ethernet statistics entries.

rmonStatsEntry row .1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1

A collection of statistics kept for a particular
Ethernet interface. As an example, an instance of the
etherStatsPkts object might be named etherStatsPkts.1

Indexes

rmonStatsIndex

Column	Syntax	OID
rmonStatsIndex The value of this object uniquely identifies this entry.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.1
rmonStatsDataSource This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shal…	ObjectIdentifierr/w	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.2
rmonStatsOwner The entity that configured this entry and is therefore using the resources assigned to it.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.3
rmonStatsOctets The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). This object can be used as a reasonable estimate of 10-Megabi…	OctetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.4
rmonStatsPkts The total number of packets (including bad packets, broadcast packets, and multicast packets) received.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.5
rmonStatsBroadcastPkts The total number of good packets received that were directed to the broadcast address. Note that this does not include multicast packets.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.6
rmonStatsMulticastPkts The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.7
rmonStatsUndersizePkts The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.8
rmonStatsOversizePkts The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.9
rmonStatsFragments The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error…	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.10
rmonStatsJabbers The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or…	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.11
rmonStatsCRCErrors The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number…	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.12
rmonStatsCollisions The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) o…	CollisionsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.13
rmonStatsDropEvents The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has b…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.14
rmonStatsPkts64Octets The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.15
rmonStatsPkts65to127Octets The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.16
rmonStatsPkts128to255Octets The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.17
rmonStatsPkts256to511Octets The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.18
rmonStatsPkts512to1023Octets The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.19
rmonStatsPkts1024to1518Octets The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.20
rmonStatsStatus The status of this etherStats entry.	RmonStatusr/w Type Values: 1 valid 2 createRequest 3 underCreation 4 invalid	.1.3.6.1.4.1.171.10.139.4.1.3.4.3.1.1.21

A list of history control entries.

rmonHistoryControlEntry row .1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1

A list of parameters that set up a periodic sampling of
statistics. As an example, an instance of the
historyControlInterval object might be named
historyControlInterval.2

Indexes

rmonHistoryControlIndex

Column	Syntax	OID
rmonHistoryControlIndex An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.1
rmonHistoryControlDataSource This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In ord…	ObjectIdentifierr/w	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.2
rmonHistoryControlBucketsRequested The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, th…	Integer32r/w Constraints: range: 1-50	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.3
rmonHistoryControlBucketsGranted The number of discrete sampling intervals over which data shall be saved in the part of the media-specific table associated with this historyControlEntry. When the associated historyControlBucketsRequeste…	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.4
rmonHistoryControlInterval The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3…	SecondsInteger32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.5
rmonHistoryControlOwner The entity that configured this entry and is therefore using the resources assigned to it.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.6
rmonHistoryControlStatus The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1…	RmonStatusr/w Type Values: 1 valid 2 createRequest 3 underCreation 4 invalid	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.1.1.7

A list of Ethernet history entries.

rmonHistoryEntry row .1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1

An historical sample of Ethernet statistics on a particular
Ethernet interface. This sample is associated with the
historyControlEntry which set up the parameters for
a regular collection of these samples. As an examp…

Indexes

rmonHistoryIndex rmonHistorySampleIndex

Column	Syntax	OID
rmonHistoryIndex The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.1
rmonHistorySampleIndex An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.2
rmonHistoryOctets The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets).	OctetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.3
rmonHistoryPkts The number of packets (including bad packets) received during this sampling interval.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.4
rmonHistoryBroadcastPkts The number of good packets received during this sampling interval that were directed to the broadcast address.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.5
rmonHistoryMulticastPkts The number of good packets received during this sampling interval that were directed to a multicast address. Note that this number does not include packets addressed to the broadcast address.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.6
rmonHistoryUtilization The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.	Integer32 Constraints: range: 0-10000	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.7
rmonHistoryUndersizePkts The number of packets received during this sampling interval that were less than 64 octets long (excluding framing bits but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.8
rmonHistoryOversizePkts The number of packets received during this sampling interval that were longer than 1518 octets (excluding framing bits but including FCS octets) but were otherwise well formed.	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.9
rmonHistoryFragments The total number of packets received during this sampling interval that were less than 64 octets in length (excluding framing bits but including FCS octets) had either a bad Frame Check Sequence (FCS) wit…	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.10
rmonHistoryJabbers The number of packets received during this sampling interval that were longer than 1518 octets (excluding framing bits but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number …	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.11
rmonHistoryCRCErrors The number of packets received during this sampling interval that had a length (excluding framing bits but including FCS octets) between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) wit…	PacketsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.12
rmonHistoryCollisions The best estimate of the total number of collisions on this Ethernet segment during this sampling interval. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and…	CollisionsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.13
rmonHistoryDropEvents The total number of events in which packets were dropped by the probe due to lack of resources during this sampling interval. Note that this number is not necessarily the number of packets dropped, it is just the numbe…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.4.2.1.14

A list of alarm entries.

rmonAlarmEntry row .1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1

A list of parameters that set up a periodic checking
for alarm conditions. For example, an instance of the
alarmValue object might be named alarmValue.8

Indexes

rmonAlarmIndex

Column	Syntax	OID
rmonAlarmIndex An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.1
rmonAlarmInterval The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be s…	SecondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.2
rmonAlarmVariable The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. …	ObjectIdentifierr/w	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.3
rmonAlarmSampleType The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directl…	Enumerationr/w Enumerated Values: 1 absoluteValue 2 deltaValue	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.4
rmonAlarmValue The value of the statistic during the last sampling period. For example, if the sample type is deltaValue, this value will be the difference between the samples at the beginning and end of the period. If the sample ty…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.5
rmonAlarmStartupAlarm The alarm that may be sent when this entry is first set to valid. If the first sample after this entry becomes valid is greater than or equal to the risingThreshold and alarmStartupAlarm is equal to risingAlarm(1) or r…	Enumeration Enumerated Values: 1 risingAlarm 2 fallingAlarm 3 risingOrFallingAlarm	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.6
rmonAlarmRisingThreshold A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generat…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.7
rmonAlarmFallingThreshold A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generat…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.8
rmonAlarmRisingEventNumber The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.9
rmonAlarmFallingEventNumber The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If ther…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.10
rmonAlarmOwner The entity that configured this entry and is therefore using the resources assigned to it.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.11
rmonAlarmStatus The status of this alarm entry.	RmonStatusr/w Type Values: 1 valid 2 createRequest 3 underCreation 4 invalid	.1.3.6.1.4.1.171.10.139.4.1.3.4.5.1.1.12

A list of events to be generated.

rmonEventEntry row .1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1

A set of parameters that describe an event to be generated
when certain conditions are met. As an example, an instance
of the eventLastTimeSent object might be named
eventLastTimeSent.6

Indexes

rmonEventIndex

Column	Syntax	OID
rmonEventIndex An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.1
rmonEventDescription A comment describing this event entry.	OctetStringr/w Constraints: range: 0-127	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.2
rmonEventType The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management statio…	Enumerationr/w Enumerated Values: 1 none 2 log 3 snmptrap 4 logandtrap	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.3
rmonEventCommunity If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.4
rmonEventOwner The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connect…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.5
rmonEventStatus The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.	RmonStatusr/w Type Values: 1 valid 2 createRequest 3 underCreation 4 invalid	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.6
rmonEventLastTimeSent The value of sysUpTime at the time this event entry last generated an event. If this entry has not generated any events, this value will be zero.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.1.1.7

A list of events that have been logged.

rmonLogEntry row .1.3.6.1.4.1.171.10.139.4.1.3.4.6.2.1

A set of data describing an event that has been
logged. For example, an instance of the logDescription
object might be named logDescription.6.47

Indexes

rmonLogEventIndex rmonLogIndex

Column	Syntax	OID
rmonLogEventIndex The event entry that generated this log entry. The log identified by a particular value of this index is associated with the same eventEntry as identified by the same value of eventIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.2.1.1
rmonLogIndex An index that uniquely identifies an entry in the log table amongst those generated by the same eventEntries. These indexes are assigned beginning with 1 and increase by one with each new log entry. The association be…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.2.1.2
rmonLogTime The value of sysUpTime when this log entry was created.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.2.1.3
rmonLogDescription An implementation dependent description of the event that activated this log entry.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.171.10.139.4.1.3.4.6.2.1.4

Define sysDDPTable for per port settings.

ddpEntry row .1.3.6.1.4.1.171.10.139.4.1.3.14.3.1

Define sysDDPTable for per port settings.

Indexes

ddpPort

Column	Syntax	OID
ddpPort This object indicates the port index.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.139.4.1.3.14.3.1.1
ddpPortStatus This object indicates DDP status is enabled or disabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.139.4.1.3.14.3.1.2

Unicast Static FDB .

fdbUnicastStaticFDBEntry row .1.3.6.1.4.1.171.10.139.4.1.4.1.1.1.1.1

Unicast Static FDB .

Indexes

fdbUnicastStaticFDBVID fdbUnicastStaticFDBMACAddr

Column	Syntax	OID
fdbUnicastStaticFDBVID Unicast Static FDB. VID (1-4094).	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.1.1.1.1
fdbUnicastStaticFDBMACAddr Unicast Static FDB. MAC Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.1.1.1.2
fdbUnicastStaticFDBPort Unicast Static FDB. port.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.1.1.1.3
fdbUnicastStaticFDBState This object indicates the status of this entry. permanent(1) - this entry is currently in use and will remain so after the next reset of the bridge. permanentDrop(2) - This entry will filter the packet with the …	Enumerationr/w Enumerated Values: 1 permanent 2 permanentDrop	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.1.1.1.4
fdbUnicastStaticFDBRowStatus This object indicates the status of fdbUnicastStaticFDBTable to which a frame with a specific unicast address will be flooded in the event that it has not been learned. To set fdbUnicastStaticFDBPort, we have to set …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.1.1.1.5

Multicast Static FDB .

fdbMulticastStaticFDBEntry row .1.3.6.1.4.1.171.10.139.4.1.4.1.1.2.1.1

Multicast Static FDB .

Indexes

fdbMulticastStaticFDBVID fdbMulticastStaticFDBMACAddr

Column	Syntax	OID
fdbMulticastStaticFDBVID Multicast Static FDB. VID (1-4094).	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.2.1.1.1
fdbMulticastStaticFDBMACAddr Multicast Static FDB. MAC Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.2.1.1.2
fdbMulticastStaticFDBEgressPorts Multicast Static FDB. egress PortList.	PortListr/w	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.2.1.1.3
fdbMulticastStaticFDBRowStatus This object indicates the status of fdbMulticastStaticFDBTable to which a frame with a specific multicast address will be flooded in the event that it has not been learned. To set fdbMulticastStaticFDBEgressPorts, we…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.4.1.1.2.1.1.4

Multicast Static FDB .

fdbMACAddressLearningEntry row .1.3.6.1.4.1.171.10.139.4.1.4.1.2.2.1

Multicast Static FDB .

Indexes

fdbMACAddressLearningPort

Column	Syntax	OID
fdbMACAddressLearningPort MAC Address Learning. port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.139.4.1.4.1.2.2.1.1
fdbMACAddressLearningState MAC Address Learning. State.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.139.4.1.4.1.2.2.1.2

Multicast Static FDB .

fdbMACAddressEntry row .1.3.6.1.4.1.171.10.139.4.1.4.1.3.1

Multicast Static FDB .

Indexes

fdbMACAddrTabVID fdbMACAddrTabMACAddr

Column	Syntax	OID
fdbMACAddrTabVID MAC Address Table. VID (1-4094).	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.139.4.1.4.1.3.1.1
fdbMACAddrTabMACAddr MAC Address Table. MAC Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.139.4.1.4.1.3.1.2
fdbMACAddrTabType MAC Address Table. Type.	Enumeration Enumerated Values: 3 dynamic 4 self 5 static	.1.3.6.1.4.1.171.10.139.4.1.4.1.3.1.3
fdbMACAddrTabPort The port number of the port on which a frame having a source address equal to the value of the corresponding instance of dynamicFdbMacAddr has been seen.If the port is LA port, will show 'po' before port.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.139.4.1.4.1.3.1.4

A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

dot1qVlanEntry row .1.3.6.1.4.1.171.10.139.4.1.4.2.2.1

Information for a VLAN configured into the
device by (local or network) management.

Indexes

dot1qVlanid

Column	Syntax	OID
dot1qVlanid Vlan id used to identify the VLAN.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.139.4.1.4.2.2.1.1
dot1qVlanName An administratively assigned string, which may be used to identify the VLAN.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.171.10.139.4.1.4.2.2.1.2
dot1qVlanEgressPorts The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVR…	PortList	.1.3.6.1.4.1.171.10.139.4.1.4.2.2.1.3
dot1qVlanUntaggedPorts The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There …	PortList	.1.3.6.1.4.1.171.10.139.4.1.4.2.2.1.4
dot1qVlanRowStatus The status of a row in sysDot1qVlanTable. By setting this object, new entries can be created in sysDot1qVlanTable and existing entries can be removed from sysDot1qVlanTable. It can be used as specified in the SNMP v2 st…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.139.4.1.4.2.2.1.99

A table containing per port control and status
information for VLAN configuration in the device.

dot1qVlanPortEntry row .1.3.6.1.4.1.171.10.139.4.1.4.2.3.1

Information controlling VLAN configuration for a port
on the device.

Indexes

dot1qVlanPortIndex

Column	Syntax	OID
dot1qVlanPortIndex Port index.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.1
dot1qVlanPortVlanMode This is used to specify the VLAN mode for the port. Use the no command to reset the VLAN mode to the default setting.	Enumerationr/w Enumerated Values: 1 access 2 trunk 3 hybrid	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.2
dot1qVlanPortAcceptableFrameType This is used to set the acceptable types of frames by a port. Use the no form of the command to reset to the default setting.	Enumerationr/w Enumerated Values: 1 admitAll 2 admitTagged 3 admitUntagged	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.3
dot1qVlanPortIngressChecking This is used to enable ingress checking for frames received by a port. Use the no command to disable the ingress check.	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.4
dot1qVlanPortNativeVlanStatus This object indicates whether enable tagging or untagging mode of the native VLAN on the interface. This value is meaningful only to TRUNK port.Access port and hybrid port MUST keep disabled.	Enumerationr/w Enumerated Values: 0 disable 1 tag 2 untag	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.5
dot1qVlanPortNativeVlanId The VLAN-ID assigned to untagged frames received on this port. The port in native VLAN will also been set as untagged as default setting.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.6
dot1qVlanPortTagVlanList The tagged VLAN list which the port belongs to.	VlanListr/w	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.7
dot1qVlanPortUntagVlanList The untagged VLAN list which the port belongs to.	VlanListr/w	.1.3.6.1.4.1.171.10.139.4.1.4.2.3.1.8

This table contains Common Spanning Tree Port
Information.

stpPortConfigurationEntry row .1.3.6.1.4.1.171.10.139.4.1.4.3.2.1

A list of information maintained by every port for
Common Spanning tree.

Indexes

stpPort

Column	Syntax	OID
stpPort The Port number of the port for which this entry contains spanning tree information.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.1
stpPortAdminPathCost The administratively assigned value for the contribution of this port to the path cost of paths toward the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the p…	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.2
stpPortPathCost The contribution of this port to the path cost of paths towards the MSTI Root which include this port.	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.3
stpPortState Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.4
stpPortGuardRoot A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Po…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.5
stpPortLinkType The administrative point-to-point status of the LAN segment attached to this port. A value of p2p(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of shared(…	Enumerationr/w Enumerated Values: 0 p2p 1 shared 2 auto	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.6
stpPortOperLinkType The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-det…	Enumeration Enumerated Values: 1 p2p 2 shared	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.7
stpPortFast The administrative value of the Edge Port parameter. A value of edge(0) indicates that this port should be assumed as an edge-port and a value of disabled(1) indicates that this port should be assumed as a non-edge-por…	Enumerationr/w Enumerated Values: 0 edge 1 disabled 2 network	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.8
stpPortOperFast The operational value of the Edge Port parameter. The object is initialized to the value of stpPortFast and is set FALSE on reception of a BPDU.	Enumeration Enumerated Values: 1 edge 2 non-edge	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.9
stpPortTCNFilter A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.10
stpPortFowardBPDU This object is for enabling or disabling forward BPDU.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.11
stpPortPriority The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priori…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.12
stpPortHelloTime The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.	Integer32r/w Constraints: range: 100-200	.1.3.6.1.4.1.171.10.139.4.1.4.3.2.1.13