DECNET-PHIV-MIB Table View

Information about the state of sessions between the
node under study and the nodes found in the table.

phivEndRemoteEntry row .1.3.6.1.2.1.18.4.1.1

Information about a particular remote node as seen
from the end communication layer.

Indexes

phivEndRemoteHostNodeID

Column	Syntax	OID
phivEndRemoteHostNodeIDmandatory This value is the address of the remote node to be evaluated.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.4.1.1.1
phivEndRemoteStatemandatory This represents the operational state of the remote node being evaluated. The possible states are: ON Allows logical links. OFF Allows no new links, terminates existing …	Enumerationr/w Enumerated Values: 1 on 2 off 3 shut 4 restricted	.1.3.6.1.2.1.18.4.1.1.2
phivEndCircuitIndexmandatory A unique index value for each known circuit used to communicate with the remote node. This is the same value as phivCircuitIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.4.1.1.3
phivEndActiveLinksmandatory This read-only parameter represents the number of active logical links from the executor to the destination node.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.1.1.4
phivEndDelaymandatory This read-only parameter is the average round trip delay in seconds to the destination node. This parameter is kept on a remote node basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.1.1.5

Information about the counters associated with each end
system that is known to the entity. These counters
reflect totals from the perspective of the executor
node.

phivEndCountEntry row .1.3.6.1.2.1.18.4.2.1

Information about a particular session between two end
systems.

Indexes

phivEndCountHostNodeID

Column	Syntax	OID
phivEndCountHostNodeIDmandatory This value is the address of the remote node to be evaluated.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.4.2.1.1
phivEndCountSecsLastZeroedmandatory This value is the number of seconds that have elapsed since the counters for the node in this table row were last set to zero. This counter is located in the network management layer, but is returned with the end system…	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.2.1.2
phivEndCountUsrBytesRecmandatory Number of user bytes received from the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.3
phivEndCountUsrBytesSentmandatory Number of user bytes sent to the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.4
phivEndUCountUsrMessRecmandatory Number of user messages received from the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.5
phivEndCountUsrMessSentmandatory Number of user messages sent to the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.6
phivEndCountTotalBytesRecmandatory Number of bytes received from the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.7
phivEndCountTotalBytesSentmandatory Number of bytes sent to the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.8
phivEndCountTotalMessRecmandatory Number of messages received from the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.9
phivEndCountTotalMessSentmandatory Number of messages sent to the target host.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.4.2.1.10
phivEndCountConnectsRecdmandatory Number of connects received from the target host.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.2.1.11
phivEndCountConnectsSentmandatory Number of connects sent to the target host.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.2.1.12
phivEndCountReponseTimeoutsmandatory Number of response timeouts.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.2.1.13
phivEndCountRecdConnectResErrsmandatory Number of received connect resource errors.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.4.2.1.14

Information about the currently known DECnet Phase
IV Routes.

phivLevel1RouteEntry row .1.3.6.1.2.1.18.5.22.1

Information about the currently known DECnet Phase
IV Routes.

Indexes

phivLevel1RouteNodeAddr

Column	Syntax	OID
phivLevel1RouteNodeAddrmandatory This value is the address of the node about which routing information is contained in this level 1 routing table.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.5.22.1.1
phivLevel1RouteCircuitIndexmandatory A unique index value for each known circuit. This is the index to the circuit state table and is the same value as phivCircuitIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.5.22.1.2
phivLevel1RouteCostmandatory This read-only parameter represents the total cost over the current path to the destination node. Cost is a positive integer value associated with using a circuit. Routing routes messages (data) along the path between t…	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.5.22.1.3
phivLevel1RouteHopsmandatory This read-only parameter represents the number of hops over to a destination node. A hop is Routing value representing the logical distance between two nodes in a network. HOPS is kept on a remote node basis.	Integer32 Constraints: range: 0-127	.1.3.6.1.2.1.18.5.22.1.4
phivLevel1RouteNextNodemandatory This read-only value indicates the next node on the circuit used to get to the node under scrutiny (next hop).	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.5.22.1.5

Information about the parameters associated with all
circuits currently known.

phivCircuitParametersEntry row .1.3.6.1.2.1.18.6.1.1

Parameters information about all circuits currently
known.

Indexes

phivCircuitIndex

Column	Syntax	OID
phivCircuitIndexmandatory A unique index value for each known circuit.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.6.1.1.1
phivCircuitLineIndexmandatory The line on which this circuit is active. This is the same as the ifIndex.	InterfaceIndex	.1.3.6.1.2.1.18.6.1.1.2
phivCircuitCommonStatemandatory This value represents the circuit's Network Management operational state. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155.	Enumerationr/w Enumerated Values: 1 on 2 off 3 service 4 cleared	.1.3.6.1.2.1.18.6.1.1.3
phivCircuitCommonSubStatemandatory This value represents the circuit's Network Management operational and service substate. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155.	Enumeration Enumerated Values: 1 starting 2 reflecting 3 looping 4 loading 5 dumping 6 triggering 7 autoservice 8 autoloading 9 autodumping 10 autotriggering 11 synchronizing 12 failed 13 running	.1.3.6.1.2.1.18.6.1.1.4
phivCircuitCommonNamemandatory The name of the circuit entry in the table, for example, SVA-0 or in a level 2 router ASYNC-8 or ETHER-1).	OctetString Constraints: range: 0-16	.1.3.6.1.2.1.18.6.1.1.5
phivCircuitExecRecallTimermandatory This parameter represents the minimum number of seconds to wait before restarting the circuit. A value of 0 indicates not timer is running.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.18.6.1.1.6
phivCircuitCommonTypemandatory Represents the type of the circuit. For X.25 circuits, the value must be set to X25. For DDCMP and Ethernet circuits it is read only and is the same value as the protocol of the associated line. NOTE: Values 1 - 5 are i…	Enumeration Enumerated Values: 1 ddcmp-point 2 ddcmp-control 3 ddcmp-tributary 4 x25 5 ddcmp-dmc 6 ethernet 7 ci 8 qp2-dte20 9 bisync 14 other 15 fddi	.1.3.6.1.2.1.18.6.1.1.7
phivCircuitServicemandatory This value indicates whether or not Network Management allows service operations on a circuit. The values for service-control are as follows: ENABLED SERVICE state and/or service functions are …	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.2.1.18.6.1.1.8
phivCircuitExecCostmandatory This value represents the routing cost of the circuit. Routing sends messages along the path between two nodes having the smallest cost.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.2.1.18.6.1.1.9
phivCircuitExecHelloTimermandatory This value determines the frequency of Routing Hello messages sent to the adjacent node on the circuit.	Integer32r/w Constraints: range: 1-8191	.1.3.6.1.2.1.18.6.1.1.10

Information about the counters associated with all
circuits currently known.

phivCircuitCountEntry row .1.3.6.1.2.1.18.6.2.1

Counter information about all circuits currently known

Indexes

phivCircuitIndex

Column	Syntax	OID
phivCircuitCountSecLastZeroedmandatory Number of seconds since the circuit counters for this circuit were last zeroed.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.6.2.1.1
phivCircuitCountTermPacketsRecdmandatory Number of terminating packets received on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.2
phivCircuitCountOriginPackSentmandatory Number of originating packets sent on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.3
phivCircuitCountTermCongLossmandatory Number of terminating congestion losses on this circuit.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.6.2.1.4
phivCircuitCountCorruptLossmandatory Number of corruption losses on this circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.6.2.1.5
phivCircuitCountTransitPksRecdmandatory Number of Transit packets received on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.6
phivCircuitCountTransitPkSentmandatory Number of transit packets sent on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.7
phivCircuitCountTransitCongestLossmandatory Number of transit congestion losses on this circuit.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.6.2.1.8
phivCircuitCountCircuitDownmandatory Number of circuit downs on this circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.6.2.1.9
phivCircuitCountInitFailuremandatory Number of Initialization failures on this circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.6.2.1.10
phivCircuitCountAdjDownmandatory This counter indicates the number of adjacency losses that result from any of the following: Node listener timeout Invalid data received at node listener Unexpected control (initialization or verification…	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.11
phivCircuitCountPeakAdjmandatory This counter indicates the maximum number of nodes that are up on the circuit.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.6.2.1.12
phivCircuitCountBytesRecdmandatory Number of bytes received on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.13
phivCircuitCountBytesSentmandatory Number of bytes sent on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.14
phivCircuitCountDataBlocksRecdmandatory Number of data blocks received on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.15
phivCircuitCountDataBlocksSentmandatory Number of data blocks sent on this circuit.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.6.2.1.16
phivCircuitCountUsrBuffUnavmandatory Number of user buffer unavailable errors.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.6.2.1.17

Information about DDCMP circuit parameters.

phivDDCMPCircuitParametersEntry row .1.3.6.1.2.1.18.7.1.1

Parameters information about DDCMP circuits currently
known.

Indexes

phivDDCMPCircuitIndex

Column	Syntax	OID
phivDDCMPCircuitIndexmandatory A unique index value for each known DDCMP circuit. This is the same value as phivCircuitIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.7.1.1.1
phivDDCMPCircuitAdjNodeAddrmandatory The address of the adjacent node.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.7.1.1.2
phivDDCMPCircuitTributarymandatory This value represents the Data Link physical tributary address of the circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.1.1.3

Information about the DDCMP counters associated with all
circuits currently known.

phivDDCMPCircuitCountEntry row .1.3.6.1.2.1.18.7.2.1

Counter information about DDCMP circuits now known

Indexes

phivCircuitIndex

Column	Syntax	OID
phivDDCMPCircuitErrorsInbdmandatory Number of Data errors inbound.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.1
phivDDCMPCircuitErrorsOutbdmandatory Number of outbound data errors.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.2
phivDDCMPCircuitRmteReplyTimeoutsmandatory Number of remote reply timeouts.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.3
phivDDCMPCircuitLocalReplyTimeoutsmandatory Number of local Reply timeouts.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.4
phivDDCMPCircuitRmteBuffErrorsmandatory Number of remote reply time out errors.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.5
phivDDCMPCircuitLocalBuffErrorsmandatory Number of local buffer errors.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.6
phivDDCMPCircuitSelectIntervalsElapmandatory Selection intervals that have elapsed.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.7.2.1.7
phivDDCMPCircuitSelectTimeoutsmandatory Number of selection timeouts.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.2.1.8

The DDCMP Line Count Table.

phivDDCMPLineCountEntry row .1.3.6.1.2.1.18.7.3.1

There is one entry in the table for each line.

Indexes

phivDDCMPLineCountIndex

Column	Syntax	OID
phivDDCMPLineCountIndexmandatory The line on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of phivLineIndex. This value is the ifIndex.	InterfaceIndex	.1.3.6.1.2.1.18.7.3.1.1
phivDDCMPLineCountDataErrsInmandatory Number of data errors inbound.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.3.1.2
phivDDCMPLineCountRmteStationErrsmandatory Number of remote station errors.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.3.1.3
phivDDCMPLineCountLocalStationErrsmandatory Number of local station errors.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.7.3.1.4

Information about control circuit parameters.

phivControlParametersEntry row .1.3.6.1.2.1.18.8.5.1

Parameters information about control circuits
currently known.

Indexes

phivControlCircuitIndex

Column	Syntax	OID
phivControlCircuitIndexmandatory A unique index value for each known multipoint control circuit. This is the same value as phivCircuitIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.8.5.1.1
phivControlBabbleTimermandatory This value represents the number of milliseconds that a selected tributary or remote half-duplex station is allowed to transmit.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.18.8.5.1.2
phivControlMaxBuffsmandatory This value represents the maximum number of buffers the tributary can use from a common buffer pool. If not set, there is no common buffer pool and buffers are explicitly supplied by the higher level. Count is a decimal…	Integer32r/w Constraints: range: 1-254	.1.3.6.1.2.1.18.8.5.1.3
phivControlMaxTransmitsmandatory This value represents the maximum number of data messages that can be transmitted at one time. Count is a decimal integer in the range 1-255.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.2.1.18.8.5.1.4
phivControlDyingBasemandatory This value represents the base priority to which a tributary is reset each time it has been polled. A separate base can be set for each of the indicated polling states. Base is a decimal integer in the range 0-255. If …	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.18.8.5.1.5
phivControlDyingIncrementmandatory This value represents the increment added to the tributary priority each time the scheduling timer expires. If not set, the defaults are: active, 0; inactive, 64; and dying, 16.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.18.8.5.1.6
phivControlDeadThresholdmandatory This value represents the number of times to poll the active, inactive, or dying tributary before changing its polling state to dead because of receive timeouts. Count is a decimal integer in the range 0-255.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.18.8.5.1.7
phivControlDyingThresholdmandatory This value represents the number of times to poll the active or inactive tributary before changing its polling state to dying because of receive timeouts. Count is a decimal integer in the range 0-255.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.18.8.5.1.8
phivControlInactTresholdmandatory This value represents the number of times to poll the active tributary before changing its polling state to inactive because of no data response. Count is a decimal integer in the range 0-255.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.18.8.5.1.9
phivControlPollingStatemandatory This value represents the state of the tributary relative to the multipoint polling algorithm. If not set the default is AUTOMATIC. The possible states are: AUTOMATIC The tributary's sta…	Enumerationr/w Enumerated Values: 1 automatic 2 active 3 inactive 4 dying 5 dead	.1.3.6.1.2.1.18.8.5.1.10
phivControlPollingSubStatemandatory This value represents the tributary's state as determined by the polling algorithm. This applies only when the polling state is AUTOMATIC and is read-only to Network Management. Polling-substate is one of ACTIVE, INAC…	Enumeration Enumerated Values: 1 active 2 inactive 3 dying 4 dead	.1.3.6.1.2.1.18.8.5.1.11
phivControlTransTimermandatory This value represents the number of milliseconds to delay between data message transmits. Milliseconds is a decimal integer in the range 0-65535.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.18.8.5.1.12

Information about ethernet link parameters.

phivEthLinkParametersEntry row .1.3.6.1.2.1.18.9.1.1

Parameter information about ethernet links currently
known.

Indexes

phivEthLinkIndex

Column	Syntax	OID
phivEthLinkIndexmandatory The circuit over which this links information is collected. This is the same as phivCircuitIndex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.9.1.1.1
phivEthDesigRouterNodeAddrmandatory This value is the address of the designated router.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.9.1.1.2
phivEthMaxRoutersmandatory This parameter is the maximum number of routers (other than the executor itself) allowed on the circuit by Routing for circuits that are owned by the executor node.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.18.9.1.1.3
phivEthRouterPrimandatory This parameter is the priority that this router is to have in the selection of designated router for the circuit on circuits that are owned by the executor node.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.2.1.18.9.1.1.4
phivEthHardwareAddrmandatory This read-only parameter is the address that is associated with the line device hardware as seen by the DECnet Software. This value is not the same as ifPhysAddress.	OctetString Constraints: range: 6-6	.1.3.6.1.2.1.18.9.1.1.5

Information about ethernet link counters.

phivCountersCountEntry row .1.3.6.1.2.1.18.10.1.1

Counter information about ethernet links currently
known.

Indexes

phivCountersIndex

Column	Syntax	OID
phivCountersIndexmandatory The interface to which these counters apply. This is the same interface as identified by the same value of phivLineIndex. This value is the ifIndex.	InterfaceIndex	.1.3.6.1.2.1.18.10.1.1.1
phivCountersCountBytesRecdmandatory Number of bytes received over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.2
phivCountersCountBytesSentmandatory Number of bytes sent over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.3
phivCountersCountDataBlocksRecdobsolete Number of data blocks received over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.4
phivCountersCountDataBlocksSentobsolete Number of data blocks sent over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.5
phivCountersCountEthUsrBuffUnavmandatory Number of user buffer unavailable errors over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.6
phivCountersCountMcastBytesRecdmandatory Number of multicast bytes received over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.7
phivCountersCountDataBlksRecdmandatory Number of data blocks received over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.8
phivCountersCountDataBlksSentmandatory Number of data blocks sent over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.9
phivCountersCountMcastBlksRecdmandatory Number of multicast blocks received over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.10
phivCountersCountBlksSentDefmandatory Number of blocks sent, initially deferred over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.11
phivCountersCountBlksSentSingleColmandatory Number of blocks sent, single collision over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.12
phivCountersCountBlksSentMultColmandatory Number of blocks sent, multiple collisions over this link.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.18.10.1.1.13
phivCountersCountSendFailuremandatory Number of send failures over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.14
phivCountersCountCollDetectFailuremandatory Number of collision detect check failures over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.15
phivCountersCountReceiveFailuremandatory Number of receive failures over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.16
phivCountersCountUnrecFrameDestmandatory Number of unrecognized frame destinations over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.17
phivCountersCountDataOvermandatory Number of data overruns over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.18
phivCountersCountSysBuffUnavmandatory Number of system buffer unavailables over this link.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.19
phivCountersCountUsrBuffUnavmandatory Number of user buffer unavailables.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.10.1.1.20

The Adjacency Table.

phivAdjEntry row .1.3.6.1.2.1.18.11.1.1

There is one entry in the table for each adjacency.

Indexes

phivAdjCircuitIndex

Column	Syntax	OID
phivAdjCircuitIndexobsolete A unique index value for each known circuit.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.18.11.1.1.1
phivAdjNodeAddrobsolete The address of the adjacent node.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.11.1.1.2
phivAdjBlockSizeobsolete This read-only parameter is the block size that was negotiated with the adjacent Routing layer during Routing initialization over a particular circuit. It includes the routing header, but excludes the data link header. …	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.18.11.1.1.3
phivAdjListenTimerobsolete This value determines the maximum number of seconds allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during Routing i…	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.11.1.1.4
phivAdjCircuitEtherServPhysAddrobsolete This parameter indicates the Ethernet physical address of an adjacent node that is being serviced on this circuit. This parameter is a qualifier for SERVICE SUBSTATE.	OctetString Constraints: range: 6-6	.1.3.6.1.2.1.18.11.1.1.5
phivAdjTypeobsolete This parameter indicates the type of adjacency. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The routing-III and nonrouting-III values ar…	Enumeration Enumerated Values: 1 routing-III 2 nonrouting-III 3 area 4 routing-IV 5 nonrouting-IV	.1.3.6.1.2.1.18.11.1.1.6
phivAdjStateobsolete This value indicates the state of a router adjacency. On adjacencies over a circuit of type (phivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (phivAdjType) ROUTING IV or AREA, this variable is…	Enumeration Enumerated Values: 1 initializing 2 up 3 run 4 circuit-rejected 5 data-link-start 6 routing-layer-initialize 7 routing-layer-verify 8 routing-layer-complete 9 off 10 halt	.1.3.6.1.2.1.18.11.1.1.7
phivAdjPriorityobsolete Priority assigned by the adjacent node for this circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.11.1.1.8
phivAdjExecListenTimerobsolete This read-only value determines the maximum number of seconds allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during…	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.11.1.1.9

The Adjacent Node Table.

phivAdjNodeEntry row .1.3.6.1.2.1.18.11.2.1

There is one entry in the table for each adjacency.

Indexes

phivAdjNodeCircuitIndex phivAdjAddr

Column	Syntax	OID
phivAdjNodeCircuitIndexmandatory A unique index value for each known circuit. This value is the same as phivCircuitIndex and identifies the circuit over which the adjacency is realized.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.11.2.1.1
phivAdjAddrmandatory The address of the adjacent node.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.11.2.1.2
phivAdjNodeBlockSizemandatory This read-only parameter is the block size that was negotiated with the adjacent Routing layer during Routing initialization over a particular circuit. It includes the routing header, but excludes the data link header. …	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.18.11.2.1.3
phivAdjNodeListenTimermandatory This value determines the maximum number of seconds allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during Routing i…	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.11.2.1.4
phivAdjNodeCircuitEtherServPhysAddrmandatory This parameter indicates the Ethernet physical address of an adjacent node that is being serviced on this circuit. This parameter is a qualifier for SERVICE SUBSTATE.	OctetString Constraints: range: 6-6	.1.3.6.1.2.1.18.11.2.1.5
phivAdjNodeTypemandatory This parameter indicates the type of adjacency. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The routing-III and nonrouting-III values ar…	Enumeration Enumerated Values: 1 routing-III 2 nonrouting-III 3 area 4 routing-IV 5 nonrouting-IV	.1.3.6.1.2.1.18.11.2.1.6
phivAdjNodeStatemandatory This value indicates the state of a router adjacency. On adjacencies over a circuit of type (phivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (phivAdjNodeType) ROUTING IV or AREA, this variabl…	Enumeration Enumerated Values: 1 initializing 2 up 3 run 4 circuit-rejected 5 data-link-start 6 routing-layer-initialize 7 routing-layer-verify 8 routing-layer-complete 9 off 10 halt	.1.3.6.1.2.1.18.11.2.1.7
phivAdjNodePrioritymandatory Priority assigned by the adjacent node for this circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.11.2.1.8

The Line Table.

phivLineEntry row .1.3.6.1.2.1.18.12.1.1

There is one entry in the table for each line.

Indexes

phivLineIndex

Column	Syntax	OID
phivLineIndexmandatory The line on which this entry's equivalence is effective. This is the same as the ifIndex.	InterfaceIndex	.1.3.6.1.2.1.18.12.1.1.1
phivLineNamemandatory The name of the line on this row of the table.	OctetString Constraints: range: 0-16	.1.3.6.1.2.1.18.12.1.1.2
phivLineStatemandatory This value represents Network Management operational state. NOTE that these values are incremented by one compared to the standard DECnet values.	Enumeration Enumerated Values: 1 on 2 off 3 service 4 cleared	.1.3.6.1.2.1.18.12.1.1.3
phivLineSubstatemandatory This value represents the line's read-only Network Management substate. NOTE that these values are incremented by one compared to the standard DECnet values.	Enumeration Enumerated Values: 1 starting 2 reflecting 3 looping 4 loading 5 dumping 6 triggering 7 auto-service 8 auto-loading 9 auto-dumping 10 auto-triggering 11 synchronizing 12 failed 13 running	.1.3.6.1.2.1.18.12.1.1.4
phivLineServicemandatory This value represents the line's read-only Network Management service. NOTE that these values are incremented by one compared to the standard DECnet values and OTHER is a new addition.	Enumeration Enumerated Values: 1 starting 2 reflecting 3 looping 4 other	.1.3.6.1.2.1.18.12.1.1.5
phivLineDevicemandatory This value represents the Physical Link device to be used on the line.	OctetString Constraints: range: 0-16	.1.3.6.1.2.1.18.12.1.1.6
phivLineReceiveBuffsmandatory This value represents the number of receive buffers reserved for the line. It is a decimal number in the range 0-65535. 0 is supported for those vendors that do not reserve buffers on a per line basis and use a pool of…	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.18.12.1.1.7
phivLineProtocolmandatory This value represents the protocol used on the line device. Note that these values are incremented by one compared to the standard DECnet values.	Enumeration Enumerated Values: 1 ddcmp-point 2 ddcmp-control 3 ddcmp-tributary 4 reserved 5 ddcmp-dmc 6 olapb 7 ethernet 8 ci 9 qp2 14 other 15 fddi	.1.3.6.1.2.1.18.12.1.1.8
phivLineServiceTimermandatory This value represents the amount of time in milliseconds allowed to elapse before a Data Link receive request completes while doing service operations.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.12.1.1.9
phivLineMaxBlockmandatory This value represents the Data Link maximum block size on the line.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.12.1.1.10

The Non Broadcast Table.

phivNonBroadcastEntry row .1.3.6.1.2.1.18.14.1.1

There is one entry in the table for each
Non Broadcast line.

Indexes

phivNonBroadcastIndex

Column	Syntax	OID
phivNonBroadcastIndexmandatory The Non Broadcast line on which this entry's equivalence is effective. This is the same value as the ifIndex.	InterfaceIndex	.1.3.6.1.2.1.18.14.1.1.1
phivNonBroadcastControllermandatory This value represents the Physical Link hardware controller mode for the line device. The values for controller-mode are: NORMAL For normal controller operating mode. LOOPBACK For software…	Enumeration Enumerated Values: 1 normal 2 loopback 3 other	.1.3.6.1.2.1.18.14.1.1.2
phivNonBroadcastDuplexmandatory This value represents the Physical Link hardware duplex mode of the line device. The possible modes are: FULL Full-duplex HALF Half-duplex Note that these values are incremented by one …	Enumeration Enumerated Values: 1 full 2 half	.1.3.6.1.2.1.18.14.1.1.3
phivNonBroadcastClockmandatory This value represents the Physical Link hardware clock mode for the line device. The values for clock-mode are: INTERNAL For software controllable loopback use of the clock. On those devices that can supp…	Enumeration Enumerated Values: 1 external 2 internal 3 other	.1.3.6.1.2.1.18.14.1.1.4
phivNonBroadcastRetransmitTimermandatory This value represents number of milliseconds before the Data Link retransmits a block on the line. On half-duplex lines, this parameter is the select timer.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.14.1.1.5

Table of information kept on all areas known to
this unit.

phivAreaEntry row .1.3.6.1.2.1.18.15.1.1

The area routing information.

Indexes

phivAreaNum

Column	Syntax	OID
phivAreaNummandatory This value indicates the area number of this entry.	Integer32 Constraints: range: 0-64	.1.3.6.1.2.1.18.15.1.1.1
phivAreaStatemandatory This value indicates the state of the area	Enumeration Enumerated Values: 4 reachable 5 unreachable	.1.3.6.1.2.1.18.15.1.1.2
phivAreaCostmandatory The total cost over the current path to the destination area. Cost is a value associated with using a circuit. Routing routes messages (data) along the path between 2 areas with the smallest cost.	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.18.15.1.1.3
phivAreaHopsmandatory The number of hops to a destination area. A hop is the routing value representing the logical distance between two areas in network.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.18.15.1.1.4
phivAreaNextNodemandatory The next node on the circuit used to get to the area under scrutiny.	PhivAddr Type Constraints: range: 2	.1.3.6.1.2.1.18.15.1.1.5
phivAreaCircuitIndexmandatory A unique index value for each known circuit.	Integer32 Constraints: range: 1-65535	.1.3.6.1.2.1.18.15.1.1.6