CISCO-OPTICAL-MONITOR-MIB Table View

This table provides objects to monitor optical
parameters in a network element. It also provides
objects for setting high and low threshold levels, with
configurable severities, on these monitored parameters.

cOpticalMonEntry row .1.3.6.1.4.1.9.9.264.1.1.1.1

An entry in the cOpticalMonTable provides objects to
monitor an optical parameter and set threshold levels
on that parameter, at an optical interface.

Note that the set of monitored optical parameters may v…

Indexes

IF-MIBifIndex cOpticalMonDirection cOpticalMonLocation cOpticalMonParameterType

Column	Syntax	OID
cOpticalMonDirection This object indicates the direction monitored for the optical interface, in this entry.	OpticalIfDirection Type Values: 1 receive 2 transmit 3 notApplicable	.1.3.6.1.4.1.9.9.264.1.1.1.1.1
cOpticalMonLocation This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface.	OpticalIfMonLocation Type Values: 1 beforeAdjustment 2 afterAdjustment 3 notApplicable	.1.3.6.1.4.1.9.9.264.1.1.1.1.2
cOpticalMonParameterType This object specifies the optical parameter that is being monitored in this entry.	OpticalParameterType Type Values: 1 power 2 acPower 3 ambientTemp 4 laserTemp 5 biasCurrent 6 peltierCurrent 7 xcvrVoltage	.1.3.6.1.4.1.9.9.264.1.1.1.1.3
cOpticalParameterValue This object gives the value measured for the particular optical parameter specified by the cOpticalMonParameterType object.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.1.1.1.4
cOpticalParamHighAlarmThresh This object is used to set a high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from below the value configu…	OpticalParameterValuer/w Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.1.1.1.5
cOpticalParamHighAlarmSev This object is used to specify a severity level associated with the high alarm threshold given by the cOpticalParamHighAlarmThresh object. The values 'notAlarmed', 'notReported', and 'cleared' do not apply. …	OpticalAlarmSeverityr/w Type Values: 1 critical 2 major 3 minor 4 notAlarmed 5 notReported 6 cleared	.1.3.6.1.4.1.9.9.264.1.1.1.1.6
cOpticalParamHighWarningThresh This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by cOpticalParameterValue goes from below …	OpticalParameterValuer/w Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.1.1.1.7
cOpticalParamHighWarningSev This object is used to specify a severity level associated with the high warning threshold given by the cOpticalParamHighWarningThresh object. The values 'critical', 'major', and 'cleared' do not apply. T…	OpticalAlarmSeverityr/w Type Values: 1 critical 2 major 3 minor 4 notAlarmed 5 notReported 6 cleared	.1.3.6.1.4.1.9.9.264.1.1.1.1.8
cOpticalParamLowAlarmThresh This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configur…	OpticalParameterValuer/w Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.1.1.1.9
cOpticalParamLowAlarmSev This object is used to specify a severity level associated with the low alarm threshold given by the cOpticalParamLowAlarmThresh object. The values 'notAlarmed', 'notReported', and 'cleared' do not apply. …	OpticalAlarmSeverityr/w Type Values: 1 critical 2 major 3 minor 4 notAlarmed 5 notReported 6 cleared	.1.3.6.1.4.1.9.9.264.1.1.1.1.10
cOpticalParamLowWarningThresh This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by cOpticalParameterValue goes from above t…	OpticalParameterValuer/w Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.1.1.1.11
cOpticalParamLowWarningSev This object is used to specify a severity level associated with the low warning threshold given by the cOpticalParamLowWarningThresh object. The values 'critical', 'major', and 'cleared' do not apply. The…	OpticalAlarmSeverityr/w Type Values: 1 critical 2 major 3 minor 4 notAlarmed 5 notReported 6 cleared	.1.3.6.1.4.1.9.9.264.1.1.1.1.12
cOpticalParamAlarmStatus This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the corresponding bi…	OpticalAlarmStatus Type Constraints: range: 1	.1.3.6.1.4.1.9.9.264.1.1.1.1.13
cOpticalParamAlarmCurMaxThresh This object indicates the threshold value of the highest severity threshold that is currently being exceeded on the interface, for the optical parameter. If no threshold value is currently being exceeded, then the value…	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.1.1.1.14
cOpticalParamAlarmCurMaxSev This object indicates the maximum severity of any thresholds that are currently being exceeded on the interface, for the optical parameter.	OpticalAlarmSeverity Type Values: 1 critical 2 major 3 minor 4 notAlarmed 5 notReported 6 cleared	.1.3.6.1.4.1.9.9.264.1.1.1.1.15
cOpticalParamAlarmLastChange This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded or cleared on the interface.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.264.1.1.1.1.16
cOpticalMon15MinValidIntervals This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number…	Unsigned32 Constraints: range: 0-96	.1.3.6.1.4.1.9.9.264.1.1.1.1.17
cOpticalMon24HrValidIntervals This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be 0 if the measurement was (re-)star…	Unsigned32 Constraints: range: 0-1	.1.3.6.1.4.1.9.9.264.1.1.1.1.18
cOpticalParamThreshSource This object indicates if the current value of a particular threshold in this entry is user configured value or it is a system default value. It also allows user to specify the list of thresholds for this entry which s…	Bitsr/w Enumerated Values: 0 highAlarmDefThresh 1 highWarnDefThresh 2 lowAlarmDefThresh 3 lowWarnDefThresh	.1.3.6.1.4.1.9.9.264.1.1.1.1.19

This table contains the list of optical interfaces
populated in cOpticalMonTable.

cOpticalMonIfEntry row .1.3.6.1.4.1.9.9.264.1.1.5.1

An entry containing the information for a particular optical interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cOpticalMonIfTimeInSlot This object indicates when this optical transceiver was detected by the system.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.264.1.1.5.1.1

This table contains performance monitoring data for the
various optical parameters, collected over the current 15
minute or the current 24 hour interval.

cOpticalPMCurrentEntry row .1.3.6.1.4.1.9.9.264.1.2.1.1

An entry in the cOpticalPMCurrentTable. It contains
performance monitoring data for a monitored optical
parameter at an interface, collected over the current 15
minute or the current 24 hour interval.

Note …

Indexes

cOpticalPMCurrentPeriod IF-MIBifIndex cOpticalPMCurrentDirection cOpticalPMCurrentLocation cOpticalPMCurrentParamType

Column	Syntax	OID
cOpticalPMCurrentPeriod This object indicates whether the optical parameter values given in this entry are collected over the current 15 minute or the current 24 hour interval.	OpticalPMPeriod Type Values: 1 fifteenMin 2 twentyFourHour	.1.3.6.1.4.1.9.9.264.1.2.1.1.1
cOpticalPMCurrentDirection This object indicates the direction monitored for the optical interface, in this entry.	OpticalIfDirection Type Values: 1 receive 2 transmit 3 notApplicable	.1.3.6.1.4.1.9.9.264.1.2.1.1.2
cOpticalPMCurrentLocation This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface.	OpticalIfMonLocation Type Values: 1 beforeAdjustment 2 afterAdjustment 3 notApplicable	.1.3.6.1.4.1.9.9.264.1.2.1.1.3
cOpticalPMCurrentParamType This object specifies the optical parameter that is being monitored, in this entry.	OpticalParameterType Type Values: 1 power 2 acPower 3 ambientTemp 4 laserTemp 5 biasCurrent 6 peltierCurrent 7 xcvrVoltage	.1.3.6.1.4.1.9.9.264.1.2.1.1.4
cOpticalPMCurrentMaxParam This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.2.1.1.5
cOpticalPMCurrentMinParam This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.2.1.1.6
cOpticalPMCurrentMeanParam This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.2.1.1.7
cOpticalPMCurrentUnavailSecs This object is used to indicate the number of seconds, in the current 15 minute or the current 24 hour interval, for which the optical performance data is not accounted for. In the receive direction, the …	Integer32 Constraints: range: 0-86400	.1.3.6.1.4.1.9.9.264.1.2.1.1.8

This table stores performance monitoring data for the
various optical parameters, collected over previous
intervals.
          
This table can have entries for one complete 24 hour
interval and up to 96 complete 15 minute
intervals. A system is required to store at least
4 completed 15 minute intervals. The number of valid
15 minute intervals in this table is indicated by the
cOpticalMon15MinValidIntervals object and the number of
valid 24 hour intervals is indicated by the
cOpticalMon24HrValidIntervals object.

cOpticalPMIntervalEntry row .1.3.6.1.4.1.9.9.264.1.2.2.1

An entry in the cOpticalPMIntervalTable. It contains
performance monitoring data for an optical parameter,
collected over a previous interval.

Note that the set of monitored optical parameters may vary
base…

Indexes

cOpticalPMIntervalPeriod cOpticalPMIntervalNumber IF-MIBifIndex cOpticalPMIntervalDirection cOpticalPMIntervalLocation cOpticalPMIntervalParamType

Column	Syntax	OID
cOpticalPMIntervalPeriod This object indicates whether the optical parameter values, given in this entry, are collected over a period of 15 minutes or 24 hours.	OpticalPMPeriod Type Values: 1 fifteenMin 2 twentyFourHour	.1.3.6.1.4.1.9.9.264.1.2.2.1.1
cOpticalPMIntervalNumber A number between 1 and 96, which identifies the interval for which the set of optical parameter values is available. The interval identified by 1 is the most recently completed 15 minute or 24 hour interval, and the int…	Integer32 Constraints: range: 1-96	.1.3.6.1.4.1.9.9.264.1.2.2.1.2
cOpticalPMIntervalDirection This object indicates the direction monitored for the optical interface, in this entry.	OpticalIfDirection Type Values: 1 receive 2 transmit 3 notApplicable	.1.3.6.1.4.1.9.9.264.1.2.2.1.3
cOpticalPMIntervalLocation This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface.	OpticalIfMonLocation Type Values: 1 beforeAdjustment 2 afterAdjustment 3 notApplicable	.1.3.6.1.4.1.9.9.264.1.2.2.1.4
cOpticalPMIntervalParamType This object specifies the optical parameter that is being monitored, in this entry.	OpticalParameterType Type Values: 1 power 2 acPower 3 ambientTemp 4 laserTemp 5 biasCurrent 6 peltierCurrent 7 xcvrVoltage	.1.3.6.1.4.1.9.9.264.1.2.2.1.5
cOpticalPMIntervalMaxParam This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.2.2.1.6
cOpticalPMIntervalMinParam This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.2.2.1.7
cOpticalPMIntervalMeanParam This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval.	OpticalParameterValue Type Constraints: range: -1000000..1000000	.1.3.6.1.4.1.9.9.264.1.2.2.1.8
cOpticalPMIntervalUnavailSecs This object is used to indicate the number of seconds, in the particular 15 minute or 24 hour interval, for which the optical performance data is not accounted for. In the receive direction, the performan…	Integer32 Constraints: range: 0-86400	.1.3.6.1.4.1.9.9.264.1.2.2.1.9