CISCO-LWAPP-REAP-MIB Table View

This table represents the WLAN configuration sent by
the controller to REAPs so that the APs can operate
in stand-alone mode.
          
LWAPP APs operating in REAP mode locally switch 
the data frames of the associated clients, rather 
than tunneling them through to the LWAPP controller 
as LWAPP data packets.  The LWAPP controller
passes this configuration set to the LWAPP AP during
the AP initialization so that the AP can operate
in stand-alone mode when it fails to reach the
controller.  The configuration is also passed to
the REAP when they are individually modified through
separate LWAPP messages.  The REAP updates itself
with the information received through these LWAPP
messages.
          
This table has a one-to-one relationship with
cLWlanConfigTable of the CISCO-LWAPP-WLAN-MIB.  There
exist a row in this table corresponding to each
row representing a WLAN in cLWlanConfigTable.
          
Note that the configuration represented by this 
table is applicable only for REAPs.  The 
controller will send this configuration set only to 
the REAP APs for their operation in standalone
mode.

cLReapWlanConfigEntry row .1.3.6.1.4.1.9.9.517.1.1.1.1

Each entry represents a conceptual row in
cLReapWlanConfigTable and corresponds to the
packet switching configuration for a
particular WLAN.

Indexes

CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapWlanEnLocalSwitching This object specifies the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' indicates that the AP, on which …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.1
cLReapWlanClientIpLearnEnable This object specifies whether Client IP Address learning is enabled on the controller. When layer two tunneling is employed the IP learning on controller has to be disabled. Otherwise, the controller is unable to learn…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.2
cLReapWlanApAuth This object specifies the behavior of the REAP, on where to handle the authentication of the client associated to the WLAN indicated by cLWlanIndex. A value of 'true' indicates that the AP, on which this …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.3
cLReapWlanVlanCentralSwitching This object specifies whether the AP bridges the traffic centrally. If the VLAN is not configured on the AP uplink, the AP will tunnel the traffic back to the Wireless LAN Controller (WLC) where it is registered. Then …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.4
cLReapWlanDhcpCentral This object specifies the behavior of the REAP when switching the DHCP packets of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' indicates that the AP, should t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.5
cLReapWlanDhcpOverrideDNS This object specifies the behavior of the REAP when switching the DNS frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' indicates that the AP, should tun…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.6
cLReapWlanNatPatEnabled This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this WLAN. This can be enabled only when cLReapWlanDhcpCentral is set to 'true'. A value o…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.7
cLReapWlanAssocCentral This object specifies the behavior of the REAP when handling the (re-)association management frames from the clients through the WLAN identified by cLWlanIndex. A value of 'true' indicates AP should tunne…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.1.1.1.8

This table represents the VLAN configuration of
REAPs.
          
The agent adds a row to this table corresponding to
each row representing a REAP in cLApTable of the
CISCO-LWAPP-AP-MIB.  The agent deletes the row
either when the AP dissociates from the
controller or moved out of the remote mode.

cLReapApConfigEntry row .1.3.6.1.4.1.9.9.517.1.2.1.1

Each entry represents a conceptual row in
cLReapApConfigTable and corresponds to the
VLAN configuration of a REAP.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress

Column	Syntax	OID
cLReapApNativeVlanId This object specifies the Native VLAN ID for the particular AP identified by cLApSysMacAddress. This particular object can be modified through a Set request only if the AP is a REAP. The agent is expected to reject the…	Unsigned32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.9.9.517.1.2.1.1.1
cLReapApVlanEnable This object specifies the availability of Native VLAN configured through cLReapApNativeVlanId on this REAP. A value of 'true' indicates that the VLAN configured as native through cLReapApNativeVlanId is e…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.2
cLReapHomeApEnable This object specifies if this REAP AP is used as Home AP. A value of 'true' indicates that this REAP AP is a Home AP. A value of 'false' indicates that this REAP AP is not a Home AP.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.3
cLReapApLeastLatencyJoinEnable This object specifies if this REAP AP should join controller which has least latency. A value of 'true' indicates that this REAP AP will join controller which has least latency. A value of …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.4
cLReapHomeApLocalSsidReset This object specifies to reset local SSID on a Home AP. A value of 'true' indicates that the local SSID is to be reset. A value of 'false' on this during set will return error. A value of false will be returned on get.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.5
cLReapInstallMappingRadioBackhaul This object specifies whether to enable or disable WLANs on backhaul radio. A value of 'true' indicates that wlan mapping would be enabled on backhaul radio. A value of 'false' indicates th…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.6
cLReapApResilientMode This object specifies whether to enable or disable standalone mode support on a REAP AP. A value of 'true' indicates that standalone mode would be enabled on backhaul radio. A value of 'fal…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.7
cLReapApNativeVlanLevel This object specifies to make a REAP AP to force inherit the vlan support and native vlan from the REAP group. A value of 'true' indicates that the AP should inherit the vlan support and native vlan from…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.1.1.8

This table represents the WLAN / VLAN Id mappings to be
configured for the REAP identified by
cLApSysMacAddress.
          
VLAN Id configured through this table is passed to
the respective REAP through the 'Add WLAN' LWAPP
message, sent as part of the 'Configure Response
message from the controller to the REAP, during
the initialization of the REAP. The REAP maps
the VLAN to the particular WLAN to locally switch
the data packets when those APs are in standalone
mode.  Thus, the information added through this
table is applicable for REAPs only.
          
VLANs are configured on WLANs for which local
switching of packets is enabled through
cLReapWlanEnLocalSwitching.  This means that
a row is added to this table only if there
are WLANs available on the controller with
local switching enabled and the AP is a REAP.

cLReapApVlanIdEntry row .1.3.6.1.4.1.9.9.517.1.2.2.1

Each entry represents a conceptual row that
corresponds to one WLAN / VLAN Id mapping to
be applied to the REAP identified by
cLApSysMacAddress.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapApVlanId This object specifies the VLAN ID to be mapped to the WLAN identified by cLWlanIndex.	Unsigned32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.9.9.517.1.2.2.1.1
cLReapApVlanInheritance This object specifies the inheritance to be mapped to the WLAN identified by cLWlanIndex. A value of 'ap' specifies VLAN for that WLAN is inherited from AP spcific configuration A value of…	Enumerationr/w Enumerated Values: 1 ap 2 hreapGroup 3 wlan	.1.3.6.1.4.1.9.9.517.1.2.2.1.2
cLReapApVlanRowStatus This object specifies the rowstatus of the wlan vlan mappings table	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.2.1.3
cLReapApVlanUsedBySecEthInterface This object indicates if vlan represented by cLReapApVlanId is used by any of the secondary ethernet interface when the REAP AP is in flex+bridge mode. A value of 'true' indicates cLReapApVlanId is used …	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.2.1.4

This table represents the VLAN Id- ACL mappings to be
configured for the REAP identified by 
cLApSysMacAddress.

cLReapApVlanIdAclEntry row .1.3.6.1.4.1.9.9.517.1.2.3.1

Each entry represents a conceptual row that
corresponds to one VLAN Id - ACL mapping to
be applied to the REAP identified by
cLApSysMacAddress.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress cLReapVlanId

Column	Syntax	OID
cLReapVlanId This object represents the VLAN ID to be mapped to the ACL for the access point identified by cLApSysMacAddress.	Unsigned32 Constraints: range: 1-4095	.1.3.6.1.4.1.9.9.517.1.2.3.1.1
cLReapIngressAcl This object specifies the name of the ingress Access Control List for the vlan-acl mapping.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.2.3.1.2
cLReapEgressAcl This object specifies the name of the egress Access Control List for the vlan-acl mapping.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.2.3.1.3
cLReapApVlanIdAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.3.1.4
cLReapVlanIdAclType This object represents the type of the vlan acl mapping A value of 'apSource' indicates that vlan-acl mapping applied from AP level. A value of 'groupSource' indicates that vlan-acl mappin…	Enumeration Enumerated Values: 1 apSource 2 groupSource	.1.3.6.1.4.1.9.9.517.1.2.3.1.5

This table represents the WLAN ACL mappings to be
configured for the REAP identified by
cLApSysMacAddress.
A row is added to this table only if there
are WLANs available on the controller with
local switching enabled and the AP is a REAP.

cLReapApWlanAclEntry row .1.3.6.1.4.1.9.9.517.1.2.4.1

Each entry represents a conceptual row that
corresponds to one WLAN / ACL mapping to
be applied to the REAP identified by
cLApSysMacAddress.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapApWebAuthAcl This object specifies the webauth ACL name to be mapped to the WLAN identified by cLWlanIndex. This will be applied to REAP AP only when webauth client associates to REAP AP.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.2.4.1.1
cLReapApWebAuthAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.4.1.2

This table represents the web policies associated with
an AP. Entries are added or deleted by the user
through the use of cLReapWebPolicyRowStatus.

cLReapWebPolicyAclEntry row .1.3.6.1.4.1.9.9.517.1.2.5.1

Each entry represents a conceptual row in
cLReapWebPolicyAclTable.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress cLReapWebPolicyAcl

Column	Syntax	OID
cLReapWebPolicyAcl This object represents the name of the web policy ACL to be mapped to the access point identified by cLApSysMacAddress.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.2.5.1.1
cLReapWebPolicyAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.5.1.2

This table represents the WLAN - local split ACL
mappings to be configured for the REAP AP 
identified by cLApSysMacAddress.

cLReapApLocalSplitACLEntry row .1.3.6.1.4.1.9.9.517.1.2.6.1

Each entry represents a conceptual row that
corresponds to one WLAN- local split ACL mapping
to be applied to the REAP identified by
cLApSysMacAddress.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapApLocalSplitAcl This object specifies the local split ACL name to be mapped to the WLAN identified by cLWlanIndex. This is applicable only for central switching WLANs on REAP AP	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.2.6.1.1
cLReapApLocalSplitAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.6.1.2

This object represents the behavior of the REAP
AP when switching the DHCP packets of the clients
associated to it through the WLAN identified
by cLWlanIndex.

cLReapApCentralDhcpEntry row .1.3.6.1.4.1.9.9.517.1.2.7.1

This object represents the behavior of the REAP
AP when switching the DHCP packets of the clients
associated to it through the WLAN identified
by cLWlanIndex.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapApDhcpCentral This object specifies the behavior of the REAP AP when switching the DHCP frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' specifies REAP AP will tunnel…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.7.1.1
cLReapApDhcpOverrideDNS This object specifies the behavior of the REAP AP when switching the DNS frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' specifies REAP AP will tunnel …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.7.1.2
cLReapApNatPatEnabled This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this REAP AP for the WLAN identified by cLWlanIndex. A value of 'true' specifies REAP AP w…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.2.7.1.3
cLReapApDhcpRowStatus This object represents the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.7.1.4
cLReapApInheritance This object represents the inheritance level of central DHCP configuration. It can be inherted from AP or REAP group or WLAN configuration	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.2.7.1.5

This table represents the L2 ACL mappings to be
configured for the REAP AP identified by
cLApSysMacAddress.
A row is added to this table only if there
are WLANs available on the controller with
local switching enabled and the AP is a REAP.

cLReapApL2AclEntry row .1.3.6.1.4.1.9.9.517.1.2.8.1

Each entry represents a conceptual row that
corresponds to one WLAN / L2 ACL mapping to
be applied to the REAP identified by
cLApSysMacAddress.

Indexes

CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapApL2Acl This object specifies the L2ACL name to be mapped to the WLAN identified by cLWlanIndex for this REAP AP	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.2.8.1.1
cLReapApL2AclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.2.8.1.2

This table represents the configuration for
REAPs so that the APs can be configured as a 
group.
Entries are added or deleted by the user through
the use of cLReapGroupRowStatus.

cLReapGroupConfigEntry row .1.3.6.1.4.1.9.9.517.1.3.1.1

Each entry represents a conceptual row in
cLReapGroupConfigTable.

Indexes

cLReapGroupName

Column	Syntax	OID
cLReapGroupName This object represents REAP group name and uniquely identifies an entry in cLReapGroupConfigTable.	OctetString Constraints: range: 1-64	.1.3.6.1.4.1.9.9.517.1.3.1.1.1
cLReapGroupPrimaryRadiusIndex The object specifies the value that maps to the primary RADIUS server for this group. A value of '0' indicates that the primary RADIUS server is not configured for this group.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.1.1.2
cLReapGroupSecondaryRadiusIndex The object specifies the value that maps to the secondary RADIUS server for this group. A value of '0' indicates that the secondary RADIUS server is not configured for this group.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.1.1.3
cLReapGroupStorageType This object specifies the storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.517.1.3.1.1.4
cLReapGroupRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.1.1.5
cLReapGroupRadiusPacTimeoutdeprecated This object represents timeout value for the PAC (protected access credentials). Superceded by cLReapGroupRadiusPacTimeoutCtrl.	SecondsUnsigned32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.9.9.517.1.3.1.1.6
cLReapGroupRadiusAuthorityId This object specifies the authority ID used for client association when client uses EAP-FAST mechanism.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.1.1.7
cLReapGroupRadiusAuthorityInfo This object specifies the authority information used for client association when client uses EAP-FAST mechanism.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.1.1.8
cLReapGroupRadiusServerKey This object specifies the RADIUS server key. For security the key always returns '****'.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.9.9.517.1.3.1.1.9
cLReapGroupRadiusIgnoreKey This object specifies whether anonymous provisioning is enabled. A value of 'true' indicates the controller will ignore the key configured in cLReapGroupRadiusServerKey anonymous requests. A value of 'false' indicate…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.10
cLReapGroupRadiusEnable This parameter specifies whether RADIUS is enabled. A value of 'true' specifies that RADIUS is enabled. A value of 'false' specifies that RADIUS is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.11
cLReapGroupRadiusLeapEnable This parameter specifies whether LEAP is enabled. A value of 'true' specifies that LEAP is enabled. A value of 'false' specifies that LEAP is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.12
cLReapGroupRadiusEapFastEnable This parameter specifies whether EAP-FAST is enabled. A value of 'true' specifies that EAP-FAST is enabled. A value of 'false' specifies that EAP-FAST is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.13
cLReapGroupRadiusPacTimeoutCtrl This parameter specifies timeout value for the PAC (protected access credentials). Valid range of timeout is 2 to 4095, and value 0 stands for disable.	secondsUnsigned32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.9.9.517.1.3.1.1.14
cLReapGroupEfficientApUpgradeEnable This parameter specifies whether efficient AP image upgrade is enabled. A value of 'true' indicates that efficient AP image upgrade is enabled. A value of 'false' indicates that Efficient AP image upgrade is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.15
cLReapGroupApUpgradeStart This object specifies which image REAP AP has to download from WLC upon upgrade start. A value of 'initiatePrimary' specifies AP will download primary image from WLC. A value of 'initiateBa…	Enumerationr/w Enumerated Values: 1 initiatePrimary 2 initiateBackup 3 abort	.1.3.6.1.4.1.9.9.517.1.3.1.1.16
cLReapGroupSlaveMaxRetryCount This object specifies the maximum retries the the slave AP has to try to download image from the master in the hreap group before it stars download from WLC. Range is 1 to 63	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.1.1.17
cLReapGroupPrimaryRadiusServerType This object specifies server IP address type of the primary radius server for the flexconnect group.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.3.1.1.18
cLReapGroupPrimaryRadiusServerAddress This object specifies server IP address of the primary radius server for the flexconnect group.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.19
cLReapGroupPrimaryRadiusServerPort This object specifies port number of the primary radius server for the flexconnect group.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.1.1.20
cLReapGroupPrimaryServerSecret This object specifies secret of the primary radius server for the flexconnect group.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.21
cLReapGroupSecRadiusServerType This object specifies server IP address type of the secondary radius server for the flexconnect group.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.3.1.1.22
cLReapGroupSecRadiusServerAddress This object specifies server IP address of the secondary radius server for the flexconnect group.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.23
cLReapGroupSecRadiusServerPort This object specifies port number of the secondary radius server for the flexconnect group.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.1.1.24
cLReapGroupSecServerSecret This object specifies secret of the secondary radius server for the flexconnect group.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.25
cLReapGroupRadiusPeapEnable This parameter specifies whether PEAP is enabled for that flexconect group. A value of 'true' indicates that PEAP is enabled. A value of 'false' indicates that PEAP is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.26
cLReapGroupRadiusEapTlsEnable This parameter specifies whether EAP-TLS is enabled in the flexconect group. A value of 'true' indicates that EAP-TLS is enabled. A value of 'false' indicates that EAP-TLS is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.27
cLReapGroupCertificateEapTlsEnable This parameter specifies whether certificate for EAP-TLS is enabled. A value of 'true' indicates that EAP-TLS certificate is enabled. A value of 'false' indicates that EAP-TLS certificate is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.28
cLReapGroupNativeVlanId This object specifies the Native VLAN ID for the particular flexconenct group identified by cLReapGroupName.	Unsigned32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.9.9.517.1.3.1.1.29
cLReapGroupVlanEnable This object specifies the availability of Native VLAN configured through cLReapGroupNativeVlanId on this REAP group. A value of 'true' indicates that the VLAN configured as native through cLReapGroupNativ…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.30
cLReapGroupOverrideVlanEnable This object specifies the overriding of vlans at REAP APs by the vlans available from the reap group.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.31
cLReapGroupHttpProxyIpType Thsi object specifies Ip Address type of Http proxy in flexconnect group.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.3.1.1.32
cLReapGroupHttpProxyIp This object specifies HTTP proxy Ip address in flexconect group.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.33
cLReapGroupHttpProxyPort This object specifies HTTP Proxy port in flexconnect group.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.1.1.34
cLReapGroupVlanTemplateName This object specifies the vlan template name at REAP APs by the vlans available from the reap group.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.35
cLReapGroupEfficientApJoinEnable This parameter specifies whether efficient AP image join is enabled. A value of 'true' indicates that efficient AP image upgrade is enabled. A value of 'false' indicates that Efficient AP image upgrade is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.36
cLReapGroupRadiusServerGroupName This object specifies the radius server group name entry in cLReapGroupConfigTable.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.37
cLReapGroupEapFastProfileName This object specifies the eap fast profile used for local auth in cLReapGroupConfigTable.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.38
cLReapGroupArpCacheEnabled This object specifies whether ARP cache feature is enabled for the flexconnect Access Points connected to the Wireless LAN Controller. A Value of 'True' specifies that ARP cache is enabled. A Value of 'False' specifies …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.39
cLReapGroupHomeApEnable This object specifies if the APs connected to this profile/group are used as Home APs. A value of 'true' specifies that REAP AP is a Home AP. A value of 'false' specifies that this REAP AP is not a Home AP.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.40
cLReapGroupLeastLatencyJoinEnable This object specifies if this REAP AP should join controller which has least latency. A value of 'true' specifies that this REAP AP will join controller which has least latency. A value of 'false' specifies that this RE…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.41
cLReapGroupHomeApLocalSsidReset This object can be used to reset local SSID on a Home AP. A value of true specifies that the local SSID is to be reset. A value of false on this during set will return error. A value of false will be returned on get.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.42
cLReapGroupInstallMappingRadioBackhaul This object specifies if WLANs are enabled or disabled on backhaul radio. A value of true specifies that wlan mapping would be enabled on backhaul radio. A value of false specifies that wla…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.43
cLReapGroupResilientMode This object specifies if Standalone mode support is enabled or disabled on a REAP AP. A value of true specifies that Standalone mode would be enabled on backhaul radio. A value of false spe…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.44
cLReapGroupDescription This object specifies the description of flex profile	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.1.1.45
cLReapGroupFallbackRadioShutEnabled This object specifies whether Fallback Radio Shut feature is enabled for the flexconnect Access Points connected to the Wireless LAN Controller. A value of true specifies that Fallback Radio Shut feature …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.46
cLReapCtsInlineTagging This object specifies whether cts inline tagging feature is enabled for the flexconnect Access Points connected to the Wireless LAN Controller. A Value of 'true' specifies that cts inline tagging is enabled. A Value of …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.48
cLReapIsHomeApEnable This object specifies whether OEAP is enabled. A value of 'true' enable OEAP A value of 'false' disable OEAP	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.49
cLReapCtsRolebasedEnforcement This object specifies whether cts role-based enforcement feature is enabled for the flexconnect Access Points connected to the Wireless LAN Controller. A Value of 'true' specifies that cts role-based enforcement is enab…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.50
cLReapCtsSxpAttachedProfileName This object specifies the sxp profile attached to the flex profile	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.51
cLReapGroupAccountingRadiusServerGroupName This object specifies the Radius server group for accounting attached to the flex profile	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.52
cLReapLocalRoaming This object specifies whether local roaming feature is enabled for the FlexConnect Access Points connected to the Wireless LAN Controller. A Value of 'true' specifies that local roaming is enabled. A Value of 'false' sp…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.53
cLReapGroupMdnsFlexProfileName This object specifies the mdns flex profile name entry in cLReapGroupConfigTable.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.1.1.54
cLReapIpOverlap This object specifies whether IP overlap feature is enabled for the FlexConnect Access Points connected to the Wireless LAN Controller. A Value of 'true' specifies that IP overlap is enabled. A Value of 'false' specifie…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.55
cLReapGroupDhcpBroadcastEnable This object specifies whether DHCP broadcast for locally switched clients is enabled or disabled. A value of 'true' specifies that DHCP broadcast is enabled. A value of 'false' specifies that DHCP broadcast is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.1.1.56

This table represents the group associated with
an AP. Entries are added or deleted by the user 
through the use of cLReapGroupApRowStatus.

cLReapGroupApConfigEntry row .1.3.6.1.4.1.9.9.517.1.3.2.1

Each entry represents a conceptual row in
cLReapGroupApConfigTable.

Indexes

cLReapGroupName CISCO-LWAPP-AP-MIBcLApSysMacAddress

Column	Syntax	OID
cLReapGroupApStorageType This object specifies the storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.517.1.3.2.1.1
cLReapGroupApRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.2.1.2
cLReapGroupApEntryType This object represents the entry type of the AP. A value of 'admin' represents the AP added to group by manual admin configuration A value of 'cloud' represents the AP added to group because of AP configured from cloud …	Enumeration Enumerated Values: 1 admin 2 cloud	.1.3.6.1.4.1.9.9.517.1.3.2.1.3
cLReapGroupApPnPConflict This object represents whether there is any conflict with the flexconnect group value from PnP.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.2.1.4

This table represents the group associated with
an User. Entries are added or deleted by the 
application through the use of 
cLReapGroupUserRowStatus.

cLReapGroupUserConfigEntry row .1.3.6.1.4.1.9.9.517.1.3.3.1

Each entry represents a conceptual row in
cLReapGroupUserConfigTable.

Indexes

cLReapGroupName cLReapGroupUserName

Column	Syntax	OID
cLReapGroupUserName This object represents the user name for this group. user name is used for authenticating a client associated to an AP within the group.	OctetString Constraints: range: 1-24	.1.3.6.1.4.1.9.9.517.1.3.3.1.1
cLReapGroupUserPassword This object specifies the password for this user.	OctetStringr/w Constraints: range: 1-64	.1.3.6.1.4.1.9.9.517.1.3.3.1.2
cLReapGroupUserStorageType This object specifies the storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.517.1.3.3.1.3
cLReapGroupUserRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.3.1.4

This table represents the configuration of VLAN-ACL
mappings for REAP groups.

cLReapGroupVlanAclEntry row .1.3.6.1.4.1.9.9.517.1.3.4.1

Each entry represents a conceptual row in
cLReapGroupVlanAclTable.

Indexes

cLReapGroupName cLReapGroupVlanId

Column	Syntax	OID
cLReapGroupVlanId This object represents the VLAN ID to be mapped to the ACL for the reap group identified by cLReapGroupName	Unsigned32 Constraints: range: 1-4095	.1.3.6.1.4.1.9.9.517.1.3.4.1.1
cLReapGroupIngressAcl This object specifies the name of the ingress access control list for the vlan-acl mapping for the group identified by cLReapGroupName.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.4.1.2
cLReapGroupEgressAcl This object specifies the name of the egress access control list for the vlan-acl mapping for the group identified by cLReapGroupName.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.4.1.3
cLReapGroupVlanAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.4.1.4
cLReapGroupVlanOrder This object represents the vlan order configuration on the group level.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.3.4.1.5

This table represents the configuration of wlan-acl
mappings for REAPs.

cLReapGroupAclEntry row .1.3.6.1.4.1.9.9.517.1.3.5.1

Each entry represents a conceptual row in
cLReapGroupAclTable.

Indexes

cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapGroupWebAuthAcl This object specifies the name of the webauth access control list for the wlan-acl mapping in the flexconnect group.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.5.1.1
cLReapGroupAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.5.1.2
cLReapGroupWebAuthIpv6Acl This object specifies the name of the Ipv6 webauth access control list for the wlan-acl mapping in the flexconnect group.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.5.1.3

This table represents the configuration of webpolicy
acl mappings for REAP groups.

cLReapGroupWebPolicyAclEntry row .1.3.6.1.4.1.9.9.517.1.3.6.1

Each entry represents a conceptual row in the
cLReapGroupWebPolicyAclTable.

Indexes

cLReapGroupName cLReapGroupWebPolicyAcl

Column	Syntax	OID
cLReapGroupWebPolicyAcl This object specifies the name of the webpolicy access control aist to be mapped to the REAP group.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.6.1.1
cLReapGroupWebPolicyAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.6.1.2
cLReapGroupWebPolicyAclType This object specifies whether webpolicy access control list is IPv4 or IPv6.	Enumerationr/w Enumerated Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.9.9.517.1.3.6.1.3
cLReapGroupWebPolicyAclCentWebAuth This object represents whether to Configure central-webauth for this ACL. A value of true specifies that central-webauth is enabled for ACL. A value of false specifies that central-webauth is disabled for ACL.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.6.1.4

This table represents the configuration of WLAN-ACL
mappings for local split tunneling at REAP groups.

cLReapGroupLocalSplitAclEntry row .1.3.6.1.4.1.9.9.517.1.3.7.1

Each entry represents a conceptual row in
cLReapGroupLocalSplitAclTable.

Indexes

cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapGroupLocalSplitAcl This object specifies the name of the local split access control list to be mapped to the WLAN inside REAP group	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.7.1.1
cLReapGroupLocalSplitAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.7.1.2

This table represents the configuration of central
dhcp processing for REAP APs in REAP groups

cLReapGroupCentralDhcpEntry row .1.3.6.1.4.1.9.9.517.1.3.8.1

Each entry represents a conceptual row in
cLReapGroupCentralDhcpTable.

Indexes

cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapGroupDhcpCentral This object specifies the behavior of the REAP AP part of REAP group when switching the DHCP frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' specifies …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.8.1.1
cLReapGroupDhcpOverrideDNS This object specifies the behavior of the REAP AP part of REAP group when switching the DNS frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' specifies…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.8.1.2
cLReapGroupNatPatEnabled This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this REAP AP part of REAP group for the WLAN identified by cLWlanIndex. A value of 'true'…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.8.1.3
cLReapGroupDhcpRowStatus This object represents the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.8.1.4

This table represents the WLAN / VLAN Id mappings
to be configured for the REAP identified by
REAP group name.
          
VLAN Id configured through this table is passed to
the respective REAP group identified by the 
REAP group name.

cLReapGroupVlanIdEntry row .1.3.6.1.4.1.9.9.517.1.3.9.1

Each entry represents a conceptual row that
corresponds to one WLAN / VLAN Id mapping to
be applied to the REAP identified by
cLReapGroupName.

Indexes

cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapGroupWlanVlanId This object specifies the VLAN ID to be mapped to the WLAN identified by cLWlanIndex in the REAP group.	Unsigned32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.9.9.517.1.3.9.1.1
cLReapGroupVlanRowStatus This object specifies the reap group vlan mapping row status.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.9.1.2

This table represents the WLAN / AVC parameters
mappings to be configured for the REAP identified by
REAP group name.
          
AVC parameters configured through this table is passed 
to the respective REAP group identified by the 
REAP group name.

cLReapGroupAVCFlexEntry row .1.3.6.1.4.1.9.9.517.1.3.10.1

Each entry represents a conceptual row that
corresponds to one WLAN / AVC parameters mapping to
be applied to the REAP identified by
cLReapGroupName.

Indexes

cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLReapGroupAVCFlexProfileName This object specifies the AVC profile name assigned to this WLAN in the REAP idendified by cLReapGroupName. 'none' specifies no profile is being associated. profile name 'none' should be used to de-associate profile fr…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.10.1.1
cLReapGroupNbarStatsVisibilityEnable This object specifies the user to enable or disable NBAR stats visibility. A value of 'disable' indicates NBAR stats visibility is disabled. A value of 'enable' indicates NBAR stats visibility is enabled. A value of 'w…	Enumerationr/w Enumerated Values: 1 disable 2 enable 3 wlan-specific	.1.3.6.1.4.1.9.9.517.1.3.10.1.2
cLReapGroupAVCFlexRowStatus This object specifies the rowstatus of the reap group wlan avc parameter mappings table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.10.1.3

This table defines the VLAN Name- ACL mappings to be
configured for the REAP identified by cLReapGroupVlanName.

cLReapGroupVlanNameAclEntry row .1.3.6.1.4.1.9.9.517.1.3.11.1

Each entry represents a conceptual row that corresponds to
one VLAN Name - ACL mapping to be applied to the REAP
identified by cLReapGroupVlanName.

Indexes

cLReapGroupName cLReapGroupVlanName

Column	Syntax	OID
cLReapGroupVlanName This object specifies the name of the Vlan name for the vlan-acl mapping.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.11.1.1
cLReapGroupVlanIdentifier This object specifies the VLAN ID to be mapped to the Acl for the Access Point identified by cLReapGroupVlanName.	Unsigned32r/w Constraints: range: 1-4096	.1.3.6.1.4.1.9.9.517.1.3.11.1.2
cLReapGroupAcl This object specifies the name of the Access Control List for the vlan-acl mapping.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.11.1.3
cLReapGroupVlanNameAclType This object specifies the type of the vlan acl mapping apSource - vlan-acl mapping applied from AP level. groupSource - vlan-acl mapping applied from hreap group level.	Enumeration Enumerated Values: 1 apSource 2 groupSource	.1.3.6.1.4.1.9.9.517.1.3.11.1.4
cLReapGroupVlanNameAclRowStatus This object specifies the status column for a conceptual row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.11.1.5
cLReapGroupAclIn This object specifies the name of the Ingress Access Control List for the vlan-acl mapping.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.11.1.6
cLReapGroupAclOut This object specifies the name of the Egress Access Control List for the vlan-acl mapping.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.3.11.1.7

This table defines the CTS SXP configured for the REAP
identified by cLReapCtsSxpConfigProfileName.

cLReapGroupCtsSxpEntry row .1.3.6.1.4.1.9.9.517.1.3.12.1

Each entry represents a conceptual row that corresponds to
one CTS SXP configuration be applied to the REAP identified by
cLReapGroupCtsSxp.

Indexes

cLReapCtsSxpConfigProfileName

Column	Syntax	OID
cLReapCtsSxpConfigProfileName This object specifies the cts sxp configuration profile name for the flex connect Access Points connected to the Wireless LAN controller.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.517.1.3.12.1.1
cLReapCtsSxpDefaultPassword This object specifies the cts sxp configuration Default password for the flex connect Access Points connected to the wireless LAN controller.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.3.12.1.2
cLReapCtsSxpState This object specifies if the SXP (Security Group Tag Exchange Protocol) functionality is enabled for the flex connect Access Points connected to the wireless LAN controller.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.517.1.3.12.1.3
cLReapCtsSxpListenerMinHoldTime This object specifies the minimum hold-time for SXP connections in 'listener' mode. Value of this object must be lesser than ctsxSxpListenerMaxHoldTime.	secondsUnsigned32r/w Constraints: range: 1-65534	.1.3.6.1.4.1.9.9.517.1.3.12.1.4
cLReapCtsSxpListenerMaxHoldTime This object specifies the maximum hold-time for SXP connections in 'listener' mode. Value of this object must be greater than ctsxSxpListenerMinHoldTime.	secondsUnsigned32r/w Constraints: range: 1-65534	.1.3.6.1.4.1.9.9.517.1.3.12.1.5
cLReapCtsSxpReconcilePeriod This object specifies the amount of time after which system will initiate removal of SGT mappings for a reconciled connection. A value of zero for this object indicates that SGT mappings for a reconciled …	secondsUnsigned32r/w Constraints: range: 0-64000	.1.3.6.1.4.1.9.9.517.1.3.12.1.6
cLReapCtsSxpRetryPeriod This object specifies the amount of time after which the device will make the retry attempt for the SXP connections that are not setup successfully. A value of zero for this object indicates that the devi…	secondsUnsigned32r/w Constraints: range: 0-64000	.1.3.6.1.4.1.9.9.517.1.3.12.1.7
cLReapCtsSxpSpeakerMinHoldTime This object specifies the minimum hold-time for SXP connections in 'speaker' mode.	secondsUnsigned32r/w Constraints: range: 1-65534	.1.3.6.1.4.1.9.9.517.1.3.12.1.8
cLReapCtsSxpRowStatus This object specifies the conceptual status of the row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.12.1.9

A list of SXP peers configured on this device.
It is a list of IP addresses of respective
SXP connection peers configured for this device.
SXP peers exchange security group tags information
of clients through SxpV4 protocol.

cLReapCtsSxpPeerEntry row .1.3.6.1.4.1.9.9.517.1.3.13.1

An entry containing management information of a
particular SXP peers.

Indexes

cLReapCtsSxpConfigProfileName cLReapCtsSxpPeerIpType cLReapCtsSxpPeerIp

Column	Syntax	OID
cLReapCtsSxpPeerIpType The type of Internet address of the peer SXP device.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.3.13.1.1
cLReapCtsSxpPeerIp The Internet address of the SXP peer device. The type of this address is determined by the value of cLReapCtsSxpPeerIpType object.	OctetString Constraints: range: 1-64	.1.3.6.1.4.1.9.9.517.1.3.13.1.2
cLReapCtsSxpMode This object specifies the device mode of this SXP connection. A value of 'speaker' indicates that device will acts as the speaker in this SXP connection. A value of 'listener' indicates tha…	Enumerationr/w Enumerated Values: 1 speaker 2 listener 3 both	.1.3.6.1.4.1.9.9.517.1.3.13.1.3
cLReapCtsSxpPeerPassword This object specifies to configure the password of the sxp peer device.	Enumerationr/w Enumerated Values: 0 notRequired 2 default	.1.3.6.1.4.1.9.9.517.1.3.13.1.4
cLReapCtsSxpPeerRowStatus This object specifies the conceptual status of the row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.3.13.1.5

The table represents REAP ACLs (access control lists)
on the switch.

cLReapAclEntry row .1.3.6.1.4.1.9.9.517.1.4.1.1

Each entry represents the attributes for clReapAclTable.
An entry gets added to the table on creating a
flexconnect ACL.

Indexes

cLReapAclName

Column	Syntax	OID
cLReapAclName This object represents name of the REAP access control list.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.517.1.4.1.1.1
cLReapAclApplyMode This object specifies the apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch. Mode value 'notapplied' means the ACL not applied on the switch.	Enumeration Enumerated Values: 0 notapplied 1 applied	.1.3.6.1.4.1.9.9.517.1.4.1.1.2
cLReapAclRowStatus This object specifies the row Status of the ACL.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.1.1.3
cLReapAclUrlDomainListTypedeprecated This object specifies the List type for all the urls being confiured on the acl. blackList indicates, access to all the urls configured will be denied and whiteList indicates permit. Default value is blackList.	Enumerationr/w Enumerated Values: 1 blackList 2 whiteList	.1.3.6.1.4.1.9.9.517.1.4.1.1.4

The table represents ACL Rules(access control list
entries) on the ACL with name cLReapAclName.

cLReapAclRuleEntry row .1.3.6.1.4.1.9.9.517.1.4.2.1

Each entry represents the attributes for
clReapAclRuleTable. An entry gets added to
the table on creating a rule on flexconnect
ACL.

Indexes

cLReapAclName cLReapAclRuleIndex

Column	Syntax	OID
cLReapAclRuleIndex This object represents index of the ACL rule. This can be updated to reset the sequence of the rules of an ACL.	Unsigned32 Constraints: range: 1-64	.1.3.6.1.4.1.9.9.517.1.4.2.1.1
cLReapAclRuleAction This object specifies permission mode of the rule. A value of 'deny' specifies client traffic matches this rule will be blocked. A value of 'permit' specifies client traffic matches this rule will be allowed to pass thr…	Enumerationr/w Enumerated Values: 0 deny 1 permit	.1.3.6.1.4.1.9.9.517.1.4.2.1.2
cLReapAclRuleSourceIpAddressType This object specifies source IP address type of the ACL rule. The value is limited to ipv4 only.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.4.2.1.3
cLReapAclRuleSourceIpAddress The object specifies source IP address of the ACL rule. It cab be any ipv4 source address. A value 0 implies any sourse address.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.2.1.4
cLReapAclRuleSourceIpNetmaskType This object specifies source IP netmask type of the ACL rule. The value is limited to ipv4 only.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.4.2.1.5
cLReapAclRuleSourceIpNetmask This object specifies source IP netmask of the ACL rule. A value '0' implies any source mask.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.2.1.6
cLReapAclRuleDestinationIpAddressType This object specifies destination IP address type of the ACL rule. The value is limited to ipv4 only.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.4.2.1.7
cLReapAclRuleDestinationIpAddress The object specifies destination IP address of the ACL rule. It cab be any ipv4 source address. A value '0' implies any destination address.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.2.1.8
cLReapAclRuleDestinationIpNetmaskType This object specifies destination IP netmask type of the ACL rule. The value is limited to ipv4 only.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.4.2.1.9
cLReapAclRuleDestinationIpNetmask This object specifies destination IP netmask of the ACL rule. A value '0' implies any destination mask.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.2.1.10
cLReapAclRuleProtocol This object specifies protocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 and 255. A value 256 implies that thi…	Unsigned32r/w Constraints: range: 0-256	.1.3.6.1.4.1.9.9.517.1.4.2.1.11
cLReapAclRuleStartSourcePort This object specifies source port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any'…	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.517.1.4.2.1.12
cLReapAclRuleEndSourcePort This object specifies source port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any'…	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.517.1.4.2.1.13
cLReapAclRuleStartDestinationPort This object specifies destination port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to …	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.517.1.4.2.1.14
cLReapAclRuleEndDestinationPort This object specifies destination port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to …	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.517.1.4.2.1.15
cLReapAclRuleDscp This object specifies DSCP value of the rule. A value 256 implies 'Any'.	Unsigned32r/w Constraints: range: 0-256	.1.3.6.1.4.1.9.9.517.1.4.2.1.16
cLReapAclNewRuleIndex This object specifies new index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will yield the same value as cLReapAclRuleIndex.	Unsigned32r/w Constraints: range: 1-64	.1.3.6.1.4.1.9.9.517.1.4.2.1.17
cLReapAclRuleRowStatus This object specifies row status of the ACL rule.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.2.1.18

The table listing layer2 ACLs (access control lists)
on the switch.

cLReapL2AclEntry row .1.3.6.1.4.1.9.9.517.1.4.3.1

Each entry represents the attributes for
cLReapL2AclTable.An entry gets added to the
table on creating a layer2 ACL.

Indexes

cLReapL2AclName

Column	Syntax	OID
cLReapL2AclName This object represents name of the L2 ACL on the switch.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.517.1.4.3.1.1
cLReapL2AclApplyMode This object represents the apply mode of the L2ACL on the switch. Mode value 'applied' means the L2ACL has been applied on the switch. Default mode on creation on ACL will be notapplied.	Enumeration Enumerated Values: 1 notapplied 2 applied	.1.3.6.1.4.1.9.9.517.1.4.3.1.2
cLReapL2AclRowStatus This object specifies the row Status of the L2ACL.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.3.1.3

The table represents L2Acl rules(access control list
entries) on the L2ACL with name cLReapL2AclName.

cLReapL2AclRuleEntry row .1.3.6.1.4.1.9.9.517.1.4.4.1

Each entry represents the attributes for
clReapL2AclRuleTable. An entry gets added to
the table on creating a rule on L2ACL.

Indexes

cLReapL2AclName cLReapL2AclRuleIndex

Column	Syntax	OID
cLReapL2AclRuleIndex This object represents the unique index of the L2ACL rule in REAP L2ACL. This can be updated to reset the sequence of the rules of an L2ACL. Valid range for this object is 1 to 64	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.4.4.1.1
cLReapL2AclRuleAction This object specifies the permission mode of a rule. The value of 'deny' means traffic will be blocked which meets the rule. The value of 'permits' means traffic will be allowed which meets the rule.	Enumerationr/w Enumerated Values: 1 deny 2 permit	.1.3.6.1.4.1.9.9.517.1.4.4.1.2
cLReapL2AclRuleEthertype This object specifies the etherType of the L2Acl rule. Default is 0x0	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.517.1.4.4.1.3
cLReapL2AclRuleEthertypeMask This object specifies the etherType Mask of the L2Acl rule. Default is 0x0	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.517.1.4.4.1.4
cLReapL2AclRuleDirection This object specifies the direction of the packet to which the rule may be applied. A value of 'inbound' specifies that this rule will be applied on traffic coming into switchport. A value of 'outbound' specifies that …	Enumerationr/w Enumerated Values: 1 inbound 2 outbound 3 any	.1.3.6.1.4.1.9.9.517.1.4.4.1.5
cLReapL2AclNewRuleIndex This object specifies the new Index of the L2ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will yield the same value as cLReapL2AclRuleIn…	Unsigned32r/w Constraints: range: 1-64	.1.3.6.1.4.1.9.9.517.1.4.4.1.6
cLReapL2AclRuleRowStatus This object specifies the status of a conceptual row in the ACL Rule Table. This is used to create and delete entries in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.4.1.7

This table represents url domain acl Rules
(url based Access Control List entries) on the 
 ACL with name cLReapAclName.

cLReapAclUrlDomainRuleEntry row .1.3.6.1.4.1.9.9.517.1.4.5.1

Each Entry represents the attributes for
cLReapAclUrlDomainRuleTable. An Url domain rule
entry gets added to the table on creating
a rule on flexconnect ACL.

Indexes

cLReapAclName cLReapAclUrlDomainRuleIndex

Column	Syntax	OID
cLReapAclUrlDomainRuleIndex This object specifies the index of the Url domain ACL rule. It can be used to reset the sequence of the Url rules of an ACL.	Unsigned32 Constraints: range: 1-20	.1.3.6.1.4.1.9.9.517.1.4.5.1.1
cLReapAclUrlDomainRuleUrl This object specifies the URL name for the url domain rule.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.5.1.2
cLReapAclUrlDomainRuleAction This object specifies the permission mode of url domain rule. A value of 'deny' specifies client traffic matches this rule will be blocked. A value of 'permit' specifies client traffic matches this rule …	Enumerationr/w Enumerated Values: 1 deny 2 permit	.1.3.6.1.4.1.9.9.517.1.4.5.1.3
cLReapAclUrlDomainRuleRowStatus This is the status column for this row and is used to create and delete specific instances of rows in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.5.1.4

This table represents url domain acl Rules(url based Access
Control List entries) on the ACL with name cLReapUrlListName.

cLReapUrlDomainListEntry row .1.3.6.1.4.1.9.9.517.1.4.6.1

Each Entry represents the attributes for
cLReapUrlDomainListTable.
An Url domain rule entry gets added to the table on creating
a rule on flexconnect ACL.

Indexes

cLReapUrlListName

Column	Syntax	OID
cLReapUrlListName This object specifies the URL name for the url domain rule.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.4.6.1.1
cLReapUrlDomainRuleAction This object specifies the permission mode of url domain rule. This is set through the url domain list type in the acl.	Enumeration Enumerated Values: 1 deny 2 permit	.1.3.6.1.4.1.9.9.517.1.4.6.1.2
cLReapUrlRedirectServerIpv4Type This object specifies the type of the source IP address of the ACL rule.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.4.6.1.3
cLReapUrlRedirectServerIpv4 This object specifies the source IP address of the ACL rule.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.6.1.4
cLReapUrlRedirectServerIpv6Type This object specifies the type of the source IP address of the ACL rule.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.517.1.4.6.1.5
cLReapUrlRedirectServerIpv6 This object specifies the source IP address of the ACL rule.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.517.1.4.6.1.6
cLReapUrlDomainRuleRowStatus This is the status column for this row and is used to create and delete specific instances of rows in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.6.1.7
cLReapUrlFilterID This object specifies the filter ID (an unique reference number) for urlfilter lists created.	Unsigned32 Constraints: range: 1-16	.1.3.6.1.4.1.9.9.517.1.4.6.1.8

This table represents url domain acl Rules(url based Access
Control List entries) on the ACL with name cLReapUrlListName.

cLReapUrlDomainRulesEntry row .1.3.6.1.4.1.9.9.517.1.4.7.1

Each Entry represents the attributes for
cLReapUrlDomainListTable.
An Url domain rule entry gets added to the table on creating
a rule on flexconnect ACL.

Indexes

cLReapUrlListName cLReapUrlDomainRuleUrl

Column	Syntax	OID
cLReapUrlDomainRuleUrl This object specifies the URL name for the url domain rule.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.9.9.517.1.4.7.1.1
cLReapUrlRowStatus This object specifies the row Status of the url table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.7.1.2

This table represents enhanced URL domain ACLs(URL based Access
Control List entries).

cLReapEnhancedUrlDomainListEntry row .1.3.6.1.4.1.9.9.517.1.4.8.1

Each Entry represents the attributes for
cLReapEnhancedUrlDomainListTable.

Indexes

cLReapEnhancedUrlDomainListName

Column	Syntax	OID
cLReapEnhancedUrlDomainListName This object specifies name for the enhanced URL domain ACL	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.9.9.517.1.4.8.1.1
cLReapEnhancedUrlDomainListRowStatus This is the status column for this row and is used to create and delete specific instances of rows in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.8.1.2

This table represents URL domain rules on the ACL with 
name cLReapEnhancedUrlDomainListName.

cLReapEnhancedUrlDomainRulesEntry row .1.3.6.1.4.1.9.9.517.1.4.9.1

Each Entry represents the attributes for
URL domain rule.

Indexes

cLReapEnhancedUrlDomainListName cLReapEnhancedUrlDomainRuleUrl

Column	Syntax	OID
cLReapEnhancedUrlDomainRuleUrl This object specifies the URL name for the URL domain rule.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.9.9.517.1.4.9.1.1
cLReapEnhancedUrlDomainRuleAction This object specifies the permission mode of url domain rule. A value of 'deny' specifies client traffic matches this rule will be blocked. A value of 'permit' specifies client traffic matches this rule …	Enumerationr/w Enumerated Values: 1 deny 2 permit	.1.3.6.1.4.1.9.9.517.1.4.9.1.2
cLReapEnhancedUrlDomainRulePreference This object specifies the preference of the URL domain rule.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.517.1.4.9.1.3
cLReapEnhancedUrlDomainRuleRowStatus This is the status column for this row and is used to create and delete specific instances of rows in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.517.1.4.9.1.4