CISCO-FSPF-MIB Table View

This table allows the users to configure and monitor the
Fabric Shortest Path First (FSPF) parameters on all the VSANs
configured on the local switch.
          
Entries in this tables are automatically created when VSANs 
are either created or activated (if an entry for that VSAN is
not already existing). 
          
An entry is deleted automatically from this table if either:
- the corresponding VSAN is deleted.  
              or
- the corresponding VSAN is suspended and the values of
  all writable objects in that entry have default values.
          
An entry can be created through the use of fspfRowStatus 
only as a re-creation of that entry after it was deleted
because the corresponding VSAN was suspended, and while
the VSAN continues to exist.
          
So an entry in this table exists when one or both of these
conditions holds:
- one or more configuration parameters have non-default
  values for a VSAN which is suspended, and/or
- the VSAN is active.
          
This has a number of consequences:
- an entry exists for a suspended VSAN whenever that VSAN 
  has non-default parameters.
- an entry cannot be created (via fspfRowStatus) for a
  VSAN with default parameters; instead, the agent
  creates/deletes an entry for a VSAN with default
  parameters according to whether the VSAN is active or
  suspended.
- an entry can not be created via fspfIfRowStatus unless
  non-default parameter values are (simultaneously) 
  configured for a VSAN which is suspended;
- deleting an entry via RowStatus when either the VSAN is 
  suspended and configured with non-default values or the 
  VSAN is active, is equivalent to resetting its parameters 
  to their default values.
  If the VSAN is suspended and was configured with default-
  values, then the entry would be deleted.

fspfEntry row .1.3.6.1.4.1.9.9.287.1.1.1

This entry contains the FSPF parameters on this VSAN.

Indexes

CISCO-VSAN-MIBvsanIndex

Column	Syntax	OID
fspfRegionId The autonomous region of the local switch on this VSAN.	FspfRegionIdr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.287.1.1.1.1
fspfDomainId The Domain Id of the local switch on this VSAN.	CISCO-ST-TCDomainId Type Constraints: range: 1..239	.1.3.6.1.4.1.9.9.287.1.1.1.2
fspfSpfDelay The time between when FSPF receives topology updates and when it starts the Shortest Path First (SPF) computation on this VSAN. The smaller value means that routing will react to the changes faster but the CPU usage is …	SecondsCISCO-TCTimeIntervalSec	.1.3.6.1.4.1.9.9.287.1.1.1.3
fspfSpfHoldTime The minimum time between two consecutive SPF computations on this VSAN. The smaller value means that routing will react to the changes faster but the CPU usage is greater.	MilliSecondsUnsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.1.1.1.4
fspfMinLsArrival The minimum time after accepting a Link State Record (LSR) on this VSAN before accepting another update of the same LSR on the same VSAN. An LSR update that is not accepted because of this time interval i…	MilliSecondsUnsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.1.1.1.5
fspfMinLsInterval The minimum time after this switch sends an LSR on this VSAN before it will send another update of the same LSR on the same VSAN.	MilliSecondsUnsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.1.1.1.6
fspfLsRefreshTime The interval between transmission of refresh LSRs on this VSAN.	MinutesCISCO-TCTimeIntervalMin	.1.3.6.1.4.1.9.9.287.1.1.1.7
fspfMaxAge The maximum age an LSR will be retained in the FSPF database on this VSAN. It is removed from the database after MaxAge is reached.	MinutesCISCO-TCTimeIntervalMin	.1.3.6.1.4.1.9.9.287.1.1.1.8
fspfMaxAgeCount The number of times any LSR reached fspfMaxAge in this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.9
fspfSpfComputations The number of times the SPF computation has been done on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.10
fspfChecksumErrors The number of FSPF checksum errors occurred on this on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.11
fspfLsuRxPkts Total number of Link State Update (LSU) packets received on all the interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.12
fspfLsaRxPkts Total number of Link State Acknowledgement (LSA) packets received on all the interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.13
fspfLsuTxPkts Total number of Link State Update (LSU) packets transmitted on all the interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.14
fspfLsaTxPkts Total number of Link State Acknowledgement (LSA) packets transmitted on all the interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.15
fspfHelloTxPkts Total number of HELLO packets transmitted on all interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.16
fspfHelloRxPkts Total number of HELLO packets received on all the interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.17
fspfRetransmittedLsuTxPkts Total number of LSU packets retransmitted on all the interfaces on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.18
fspfErrorRxPkts Number of invalid FSPF control packets received on all the interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.19
fspfLsrs The number of current entries for this VSAN in the fspfLsrTable.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.20
fspfCreateTime The value of sysUpTime when this entry was last created.	LastCreationTime	.1.3.6.1.4.1.9.9.287.1.1.1.21
fspfAdminStatus The desired state of FSPF on this VSAN. If value of this object is set to up (1) , then FSPF is enabled on this VSAN. If set to down (2) , then FSPF is disabled on this VSAN.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.9.9.287.1.1.1.22
fspfOperStatus State of FSPF on this VSAN. If 'fspfAdminStatus' is down (2) then the 'fspfOperStatus' should be down (2). If 'fspfAdminStatus' is changed to up (1) then 'fspfOperStatus' should change to up (1) as and when FSPF is a…	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.9.9.287.1.1.1.23
fspfSetToDefault Setting this value to 'default' changes the value of each and every every write-able object in this row to its default value. If all the configuration parameters have their default values and if the VSAN…	Enumerationr/w Enumerated Values: 1 default 2 noOp	.1.3.6.1.4.1.9.9.287.1.1.1.24
fspfRowStatus The status of conceptual row on this VSAN. This object can be used to create an entry only if the corresponding VSAN is suspended. If the VSAN is either not-existent or active, a create will fail.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.287.1.1.1.25
fspfTotalCheckSum The total checksum of all the LSRs on this VSAN.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.1.1.26

This table allows the users to configure and monitor the
Fabric Shortest Path First (FSPF) parameters on all 
interfaces on all the VSANs configured on the local switch.
          
An entry is automatically created in this table if there
is an entry in the fspfTable for a VSAN when an E_port 
comes up on that VSAN.
          
An entry is automatically deleted from this table if
either :
 a) the interface transitions to being a down interface which
    is configured with default values and which is either
    down or a non-E_port, 
                      or
 b) the fspfTable entry for the corresponding VSAN is
    deleted.
          
 Entries in this table can be created via fspfIfRowStatus
 only as the means to specify non-default parameter values
 for an interface at a time when that interface is either down
 or is a non-E_port.
          
So an entry in this table exists when one or both of these
conditions holds:
- one or more configuration parameters have non-default
  values for an interface which is either down or
  a non-E_port and corresponding VSAN has an entry
  in the fspfTable, and/or
- the interface is an E_port and it is up.
          
This has a number of consequences:
- an entry exists for a non-E_port or an E_port which is down
  whenever that interface has non-default parameters and the
  corresponding VSAN has an entry in the fspfTable;
- an entry cannot be created (via fspfIfRowStatus) for an
  interface with default parameters; instead, the agent
  creates/deletes an entry for an interface with default
  parameters according to whether the E_port is up or
  down.
- an entry can not be created via fspfIfRowStatus unless
  non-default parameter values are (simultaneously) 
  configured for an interface which is a non-E_port or a 
  down interface, and the corresponding VSAN has an entry in 
  the fspfTable.
- deleting an entry via RowStatus when either the interface 
  is down and configured with non-default values or the 
  interface is up, is equivalent to resetting its parameters
  to their default values.
  If the interface is down and was configured with default-
  values, then the entry would be deleted.

fspfIfEntry row .1.3.6.1.4.1.9.9.287.1.2.1

An entry containing information for an FSPF interface
on this VSAN. The entry is created when a FSPF is enabled
on this VSAN by creating an entry in the fspfTable on this
VSAN. 'vsanIndex' specifies a particular VSAN an…

Indexes

CISCO-VSAN-MIBvsanIndex IF-MIBifIndex

Column	Syntax	OID
fspfIfCost The administrative cost of sending a frame on this interface on this VSAN. The value 0 means that the cost has not been configured. Once the value has been configured, the value can not again be zero; so, obviously …	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.1.2.1.1
fspfIfHelloInterval Interval between the periodic HELLO messages sent on this interface on this VSAN to verify the link health. Note that this value must be same on both the interfaces on each end of the link on this VSAN.	SecondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.9.9.287.1.2.1.2
fspfIfDeadInterval Maximum time for which no HELLO messages can be received on this interface on this VSAN. After this time, the interface is assumed to be broken and removed from the database. Note that this value must be greater than th…	SecondsUnsigned32r/w Constraints: range: 2-65535	.1.3.6.1.4.1.9.9.287.1.2.1.3
fspfIfRetransmitInterval Time after which an unacknowledged link update is retransmitted on this interface on this VSAN.	SecondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.9.9.287.1.2.1.4
fspfIfLsuRxPkts Number of Link State Update (LSU) packets received on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.5
fspfIfLsaRxPkts Number of Link State Acknowledgement (LSA) packets received on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.6
fspfIfLsuTxPkts Number of Link State Update (LSU) packets transmitted on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.7
fspfIfLsaTxPkts Number of Link State Acknowledgement (LSA) packets transmitted on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.8
fspfIfHelloTxPkts Number of HELLO packets transmitted on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.9
fspfIfHelloRxPkts Number of HELLO packets received on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.10
fspfIfRetransmittedLsuTxPkts Number of LSU packets retransmitted on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.11
fspfIfErrorRxPkts Number of invalid FSPF control packets received on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.12
fspfIfInactivityExpirations Number of times the inactivity timer has expired on this interface on this VSAN since the creation of the entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.13
fspfIfNbrState The state of FSPF's 'neighbor state machine', which is the operational state of the interaction with the neighbor's interface which is connected to this interface. If the 'fspfIfAdminStatus' is down(2)…	FspfInterfaceState Type Values: 1 down 2 init 3 dbExchange 4 dbAckwait 5 dbWait 6 full	.1.3.6.1.4.1.9.9.287.1.2.1.14
fspfIfNbrDomainId The Domain Id of the neighbor on this VSAN.	CISCO-ST-TCDomainIdOrZero Type Constraints: range: 0..239	.1.3.6.1.4.1.9.9.287.1.2.1.15
fspfIfNbrPortIndex The index, as known by the neighbor, of the neighbor's interface which is connected to this interface on this VSAN.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.9.9.287.1.2.1.16
fspfIfAdminStatus The desired state of FSPF on this interface on this VSAN. If value of this object is set to 'up', then FSPF is enabled on this interface on this VSAN. If set to 'down', then FSPF is disabled on this interface on this …	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.9.9.287.1.2.1.17
fspfIfCreateTime The value of sysUpTime when this entry was last created.	LastCreationTime	.1.3.6.1.4.1.9.9.287.1.2.1.18
fspfIfSetToDefault Setting this value to 'default' changes the value of each and every every write-able object in this row to its default value. If all the configuration parameters have their default values and if the inte…	Enumerationr/w Enumerated Values: 1 default 2 noOp	.1.3.6.1.4.1.9.9.287.1.2.1.19
fspfIfRowStatus The status of the conceptual row. This object can be used to create an entry only if the corresponding VSAN is suspended and the interface is either isolated or is a non-E_port. Otherwise, a create wil…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.287.1.2.1.20

This table is the database of all (the latest incarnation 
of) the Link State Records (LSR) which are currently 
contained in the topology database.
The topology database contains the LSRs which have been 
either issued or received by the local switch on any/all 
VSANs, and which have not reached fspfMaxAge.

fspfLsrEntry row .1.3.6.1.4.1.9.9.287.2.1.1

This gives information for the most recent update of an
LSR. There is one entry for every LSR issued or received
by the local on a VSAN.

Indexes

CISCO-VSAN-MIBvsanIndex fspfLsrDomainId fspfLsrType

Column	Syntax	OID
fspfLsrDomainId Domain Id of the LSR owner on this VSAN. It is the Link State Id of this LSR.	CISCO-ST-TCDomainId Type Constraints: range: 1..239	.1.3.6.1.4.1.9.9.287.2.1.1.1
fspfLsrType Type of this LSR.	FspfLsrType Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.287.2.1.1.2
fspfLsrAdvDomainId Domain Id of the switch that is advertising the LSR on the behalf of the switch owning it.	CISCO-ST-TCDomainId Type Constraints: range: 1..239	.1.3.6.1.4.1.9.9.287.2.1.1.3
fspfLsrAge Time since this LSR was inserted into the database.	SecondsUnsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.2.1.1.4
fspfLsrIncarnationNumber The link state incarnation number of this LSR. This is used to identify most recent instance of an LSR while updating the topology database when an LSR is received. The updating of an LSR includes incrementing its incar…	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.9.9.287.2.1.1.5
fspfLsrCheckSum The checksum of the LSR.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.2.1.1.6
fspfLsrLinks Number of entries in the fspfLinkTable associated with this LSR.	Unsigned32 Constraints: range: 0-65355	.1.3.6.1.4.1.9.9.287.2.1.1.7
fspfLsrExternal This objects indicates of this is an external LSR advertized by local switch.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.287.2.1.1.8

This table contains the list of Inter-Switch Links and their
information which is part of the LSR received or issued.

fspfLinkEntry row .1.3.6.1.4.1.9.9.287.2.2.1

An entry which contains information about a link
contained in an LSR on this VSAN. An entry is created
whenever a new link appears in an (issued or received)
LSR. Also, an entry is deleted when a link no longer
appe…

Indexes

CISCO-VSAN-MIBvsanIndex fspfLsrDomainId fspfLsrType fspfLinkIndex

Column	Syntax	OID
fspfLinkIndex An arbitrary index of this link.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.287.2.2.1.1
fspfLinkNbrDomainId The Domain Id of the neighbor on the other end of this link on this VSAN.	CISCO-ST-TCDomainId Type Constraints: range: 1..239	.1.3.6.1.4.1.9.9.287.2.2.1.2
fspfLinkPortIndex The source E_port of this link, as indicated by the index value in the LSR received from the switch identified by 'fspfLsrDomainId'.	Unsigned32 Constraints: range: 0-16777215	.1.3.6.1.4.1.9.9.287.2.2.1.3
fspfLinkNbrPortIndex The destination E_port of this link, as indicated by the index value in the LSR received from the switch identified by 'fspfLinkNbrDomainId'.	Unsigned32 Constraints: range: 0-16777215	.1.3.6.1.4.1.9.9.287.2.2.1.4
fspfLinkType The type of this link.	FspfLinkType Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.287.2.2.1.5
fspfLinkCost The cost of sending a frame on this link on this VSAN. Link cost is calculated using a formula link cost = S * (1.0625e12/Baud Rate) where S (value of fspfIfCost object on inteface on the switch corresponding to…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.287.2.2.1.6