CISCO-ATM-SWITCH-FR-IWF-MIB Table View

This table contains a set of self-consistent Frame
Relay traffic parameters. It is intended to be used to
create Frame Relay to ATM interworking connections,
hence a ATM traffic service category is also included.
          
An entry in this table is associated with an
equivalent entry in the ATM traffic descriptor table
(atmTrafficDescrParamTable); the mapping is given by
the object casfTrafficDescrAtmIndex. The agent will
not permit deletion of the associated
atmTrafficDescrEntry while the Frame Relay Traffic 
Descriptor entry exists.
          
When creating an entry in this table, if the value of
casfTrafficDescrAtmIndex is specified, the following
cases are possible:
(a) if no corresponding row exists in
atmTrafficDescrParamTable, the agent will create such
a row with the given index value.
(b) if a corresponding row does exist in
atmTrafficDescrParamTable, the agent compares the
parameter values in casfTrafficDescrEntry and the
corresponding atmTrafficDescrParamEntry. If the two
entries are not equivalent, an error is returned, and
row creation fails.
          
When creating an entry in this table, if the value of
casfTrafficDescrAtmIndex is not specified, the agent
will assign a value to this object so that it refers
to an equivalent entry in the
atmTrafficDescrParamTable. If such an equivalent
entry does not already exist, the agent will create
one.
          
The agent creates rows in this table for use with
signaled connections. These are called 'transient'
rows - they disappear when the connection is torn
down, and are not saved in non-volatile memory. By
convention, transient rows usually use high-numbered
index values.
          
Entries can be deleted by setting the row status to
destroy(6). The agent denies the request if the row
is in use by existing connections.

casfTrafficDescrEntry row .1.3.6.1.4.1.9.9.112.1.1.1.1

Describes a traffic descriptor that is used by Frame
Relay connections.

Indexes

casfTrafficDescrIndex

Column	Syntax	OID
casfTrafficDescrIndex Uniquely identifies a row in this table.	CasfTrafficDescrRow Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.9.9.112.1.1.1.1.1
casfTrafficDescrCIR The value of the Committed Information Rate (CIR) parameter.	bits/secCISCO-TCUnsigned32r/w	.1.3.6.1.4.1.9.9.112.1.1.1.1.2
casfTrafficDescrBc The value of the Committed Burst Size (Bc) parameter.	bitsCISCO-TCUnsigned32r/w	.1.3.6.1.4.1.9.9.112.1.1.1.1.3
casfTrafficDescrBe The value of the Excess Burst Size (Be) parameter.	bitsCISCO-TCUnsigned32r/w	.1.3.6.1.4.1.9.9.112.1.1.1.1.4
casfTrafficDescrPIR The value of the Peak Information Rate (PIR) parameter.	bits/secCISCO-TCUnsigned32r/w	.1.3.6.1.4.1.9.9.112.1.1.1.1.5
casfTrafficDescrServCategory The service category, as defined for ATM.	Enumerationr/w Enumerated Values: 1 vbrNrt 2 abr 3 ubr 4 vbrRt	.1.3.6.1.4.1.9.9.112.1.1.1.1.6
casfTrafficDescrAtmIndex The index of the equivalent entry in the atmTrafficDescrParamTable.	r/w	.1.3.6.1.4.1.9.9.112.1.1.1.1.7
casfTrafficDescrRowStatus Used to create, delete and modify this row. None of the columnar values (other than this one) can be modified while the row is active.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.112.1.1.1.1.8

This table contains information about Frame Relay
end-points of FR-ATM interworking connections on the
switch. When an entry is created in this table, the
agent creates a corresponding entry in the
atmVclTable of ATM-MIB, to represent the
configuration on the internal ATM port. The mapping
between an entry in this table, and the corresponding
entry in the atmVclTable is shown in the
casfFAMapTable and the casfAFMapTable.
          
 Entries can be created or deleted in this table by an
 NMS using the casfVcEndptRowStatus object. 
          
 To create a PVC connection end-point, the value of
 casfVcEndptConnKind must be 'pvc'.
          
 To create a soft VC initiator end-point, set the value of
 casfVcEndptConnKind to 'spvcInitiator', and specify
 the value of casfVcEndptSpvcRemoteAddr and
 casfVcEndptSpvcRemoteType. 
          
 If the value of casfVcEndptSpvcRemoteType is
 'frameRelay', you must also specify the value of
 casfVcEndptSpvcRemoteDlci. Activating the conceptual
 row will then cause the agent to attempt to establish
 a connection to the remote frame relay interface.
          
If the value of casfVcEndptSpvcRemoteType is 'atm',
 you must specify the values of
 casfVcEndptSpvcRemoteVpi and
 casfVcEndptSpvcRemoteVci. Activating the conceptual row
 will then cause the agent to attempt to establish a
 connection to the remote ATM interface.
          
 The agent creates an entry in this table when an
 incoming signaling request causes a soft VC
 connection to be established with a local frame relay
 interface as the destination. The value of
 casfVcEndptConnKind in this case will be
 'spvcTarget'.  Such entries cannot be modified or
 deleted by network management. They will be deleted
 when the connection is removed by signaling.

casfVcEndptEntry row .1.3.6.1.4.1.9.9.112.1.2.1.1

Models a bidirectional Frame Relay VC end-point. The
ifIndex identifies an ifTable entry for a Frame Relay
interface on this device.

Indexes

IF-MIBifIndex casfVcEndptDlci

Column	Syntax	OID
casfVcEndptDlci The value of the Data Link Connection Identifier (DLCI) which identifies this connection end-point.	DlciValue Type Constraints: range: 0..4194303	.1.3.6.1.4.1.9.9.112.1.2.1.1.1
casfVcEndptRxTrafficDescrRow Identifies the entry in the casfTrafficDescrTable which applies to the receive direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connect…	CasfTrafficDescrRowr/w Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.9.9.112.1.2.1.1.2
casfVcEndptTxTrafficDescrRow Identifies the entry in the casfTrafficDescrTable which applies to the transmit direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connec…	CasfTrafficDescrRowr/w Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.9.9.112.1.2.1.1.3
casfVcEndptRxNegTrafficDescrRow Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the receive direction of this connection end-point. This object is not instantiated if this is n…	CasfTrafficDescrRow Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.9.9.112.1.2.1.1.4
casfVcEndptTxNegTrafficDescrRow Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the transmit direction of this connection endpoint. This object is not instantiated if this is not…	CasfTrafficDescrRow Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.9.9.112.1.2.1.1.5
casfVcEndptConnKind The connection kind. The value can be set prior to the row becoming 'active'. To create a pvc connection endpoint, set this value to pvc(1). To create a soft VC connection endpoint, set th…	ConnectionKindr/w Type Values: 1 pvc 2 svcIncoming 3 svcOutgoing 4 spvcInitiator 5 spvcTarget	.1.3.6.1.4.1.9.9.112.1.2.1.1.6
casfVcEndptIwfType The type of the interworking function. The value can be set prior to the row becoming 'active'.	Enumerationr/w Enumerated Values: 1 network 2 serviceTransparent 3 serviceTranslation 4 rfc1973	.1.3.6.1.4.1.9.9.112.1.2.1.1.7
casfVcEndptClpMode Specifies how to map from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side. For network interworking, clpIfDe(1) corresponds to Mode 1 as defined …	Enumerationr/w Enumerated Values: 1 clpIfDe 2 clpIsZero 3 clpIsOne	.1.3.6.1.4.1.9.9.112.1.2.1.1.8
casfVcEndptDeMode Specifies how to map from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. See the Frame Relay Forum specifications FRF.5 and FRF.8 for definitio…	Enumerationr/w Enumerated Values: 1 deIfClpOrFrsscsDe 2 deIfFrsscsDe 3 deIfClp 4 deIsZero 5 deIsOne	.1.3.6.1.4.1.9.9.112.1.2.1.1.9
casfVcEndptEfciMode Specifies how to map from FECN field in the Frame Relay PDU to the EFCI field in ATM cells, in case of service interworking. This object does not apply to network interworking. efciIfFecn(1) and efciIsZer…	Enumerationr/w Enumerated Values: 1 efciIfFecn 2 efciIsZero	.1.3.6.1.4.1.9.9.112.1.2.1.1.10
casfVcEndptUpcMode Specifies the action taken by Usage Parameter Control (UPC) at the ingress port.	Enumerationr/w Enumerated Values: 1 pass 2 tagDrop 3 tag 4 drop	.1.3.6.1.4.1.9.9.112.1.2.1.1.11
casfVcEndptSpvcRemoteAddr The ATM address of the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4). The agent will return an inconsistentValue error on…	AtmAddrr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.9.9.112.1.2.1.1.12
casfVcEndptSpvcRemoteType The type of the remote end of the soft VC. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5). The agent will return an inconsistentValue error on s…	Enumerationr/w Enumerated Values: 1 other 2 frameRelay 3 atm	.1.3.6.1.4.1.9.9.112.1.2.1.1.13
casfVcEndptSpvcRemoteDlci The DLCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteTy…	DlciValuer/w Type Constraints: range: 0..4194303	.1.3.6.1.4.1.9.9.112.1.2.1.1.14
casfVcEndptSpvcRemoteVpi The VPI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteTyp…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.9.112.1.2.1.1.15
casfVcEndptSpvcRemoteVci The VCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteTyp…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.112.1.2.1.1.16
casfVcEndptCreationTime The time when this row was created.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.112.1.2.1.1.17
casfVcEndptRcvdSigStatus The value of this object identifies the PVC status received via the local in-channel signaling procedures for this PVC end-point. This object is only pertinent for interfaces that perform the bidirectional procedures. F…	Enumeration Enumerated Values: 1 deleted 2 active 3 inactive 4 none	.1.3.6.1.4.1.9.9.112.1.2.1.1.18
casfVcEndptRowStatus Used to create, modify or delete this row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.112.1.2.1.1.19
casfVcSignalStandardCalledIe Specifies whether or not to signal the standard (from the ATM-Forum PNNI Soft PVC Addendum) format of the Called Soft PVC IE, as opposed to the proprietary encoding we have used for the network-interworking case to …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.112.1.2.1.1.20

This table contains frame relay Local Management
Interface (LMI) parameters and counters.
          
There is one entry for each frame relay
interface. Entries come and go in this table as frame
relay interfaces are created and deleted in the device.

casfFrLmiEntry row .1.3.6.1.4.1.9.9.112.1.3.1.1

Frame relay LMI objects for a particular frame relay
interface, which is identified by the ifIndex value in
the INDEX clause.

Indexes

IF-MIBifIndex

Column	Syntax	OID
casfFrLmiProtocol Identifies the Local In-Channel Signaling Protocol that is used for this frame relay port.	Enumerationr/w Enumerated Values: 1 none 2 lmi 3 ansiT1617D 4 ansiT1617B 5 ccittQ933A	.1.3.6.1.4.1.9.9.112.1.3.1.1.1
casfFrLmiType Identifies the Local In-Channel Signaling Procedure that is used for this frame relay port. A dte performs only user-side procedures. A dce performs only network-side procedures. An nni performs bidirectional procedures.	Enumerationr/w Enumerated Values: 1 dte 2 dce 3 nni	.1.3.6.1.4.1.9.9.112.1.3.1.1.2
casfFrLmiUserN391 Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.9.9.112.1.3.1.1.3
casfFrLmiUserN392 The maximum number of unanswered Status Enquiries the device shall accept before declaring the interface down.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.9.9.112.1.3.1.1.4
casfFrLmiUserN393 The number of status polling intervals over which the error threshold is counted. For example, if within N393 number of events the device receives N392 number of errors, the interface is marked as down.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.9.9.112.1.3.1.1.5
casfFrLmiUserT391 The number of seconds between successive status enquiry messages.	secondsInteger32r/w Constraints: range: 5-30	.1.3.6.1.4.1.9.9.112.1.3.1.1.6
casfFrLmiNetN392 The value of the network-side error threshold for this frame relay port.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.9.9.112.1.3.1.1.7
casfFrLmiNetN393 The value of the network-side monitored events count for this frame relay port. If, within N393 number of events, the network-side receives N392 number of errors, the interface is marked as down.	Integer32r/w Constraints: range: 0-10	.1.3.6.1.4.1.9.9.112.1.3.1.1.8
casfFrLmiNetT392 The value of the network-side polling verification timer for this frame relay port.	secondsInteger32r/w Constraints: range: 5-30	.1.3.6.1.4.1.9.9.112.1.3.1.1.9
casfFrLmiEnquiryIns Number of Status Enquiry messages received.	messagesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.3.1.1.10
casfFrLmiEnquiryOuts Number of Status Enquiry messages sent.	messagesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.3.1.1.11
casfFrLmiStatusIns Number of Status messages received.	messagesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.3.1.1.12
casfFrLmiStatusOuts Number of Status messages sent.	messagesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.3.1.1.13
casfFrLmiStatusTimeouts Number of times when timeout occurred on waiting for Status message	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.3.1.1.14
casfFrLmiStatusEnqTimeouts Number of times when timeout occurred on waiting for Status Enquiry message	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.3.1.1.15

Contains an entry for each Frame Relay interface that
supports FR-ATM interworking connections. An entry
contains interworking related parameters for the interface.

casfConfIfEntry row .1.3.6.1.4.1.9.9.112.1.3.2.1

Configuration parameters for interworking at a
Frame Relay interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
casfConfIfAtmAddress The ATM Address that identifies this interface. This address can be used to setup soft VC's to this interface over an ATM network.	AtmAddr Type Constraints: range: 0..40	.1.3.6.1.4.1.9.9.112.1.3.2.1.1
casfConfIfUpcIntent Specifies the default Usage Parameter Control (UPC) action to use at this interface for connections that do not explicitly specify a UPC action.	Enumerationr/w Enumerated Values: 1 pass 2 tagDrop 3 tag 4 drop	.1.3.6.1.4.1.9.9.112.1.3.2.1.2
casfConfIfBcDefault Specifies the default Committed Burst Size (Bc) value to use at this interface for connections that do not explicitly specify the value of Bc.	bitsInteger32r/w Constraints: range: 0-32768	.1.3.6.1.4.1.9.9.112.1.3.2.1.3
casfConfIfCledSpvcDeModeDef Specifies the default mapping from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. This is used when receiving a soft PVC Setup using the standard encoding…	Enumerationr/w Enumerated Values: 1 deIfClpOrFrsscsDe 2 deIfFrsscsDe	.1.3.6.1.4.1.9.9.112.1.3.2.1.4
casfConfIfCledSpvcClpModeDef Specifies the default mapping from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side.This is used when receiving a soft PVC Setup using the standard encoding …	Enumerationr/w Enumerated Values: 1 clpIfDe 2 clpIfIsZero 3 clpIfIsOne	.1.3.6.1.4.1.9.9.112.1.3.2.1.5

A table containing counters at Frame Relay connection
end-points. Entries in this table are created and
deleted whenever corresponding entries in the
casfVcEndptTable are created and deleted.

casfVcCountEntry row .1.3.6.1.4.1.9.9.112.1.4.1.1

Counters at a Frame Relay connection end-point, which
is identified by the ifIndex of the Frame Relay
interface and the DLCI number.

Indexes

IF-MIBifIndex casfVcEndptDlci

Column	Syntax	OID
casfVcCountReceivedFrames Number of frames received.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.1
casfVcCountReceivedOctets Number of octets received. This counter counts octets from the beginning of the frame relay header field to the end of user data.	octetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.2
casfVcCountReceivedFECNs Number of frames received from the network with the FECN (Forward Explicit Congestion Notification) bit set.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.3
casfVcCountReceivedBECNs Number of frames received from the network with the BECN (Backward Explicit Network Congestion) bit set.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.4
casfVcCountReceivedDEs Number of frames received with the Discard Eligibility (DE) bit set.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.5
casfVcCountInDiscards Number of frames received that were discarded at ingress. Possible reasons are policing, congestion.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.6
casfVcCountOutDiscards Number of frames that were to be transmitted but were discarded. Possible reasons are policing, lack of buffers.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.7
casfVcCountSentFrames Number of frames sent.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.8
casfVcCountSentOctets Number of octets sent. This counter counts octets from the beginning of the frame relay header field to the end of user data.	octetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.9
casfVcCountSentFECNs Number of frames that were sent with the FECN bit set.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.10
casfVcCountSentBECNs Number of frames sent with the BECN bit set.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.11
casfVcCountSentDEs Number of frames sent with the DE bit set.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.12
casfVcCountTaggedFECNs Number of frames for which the switch set the FECN bit.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.13
casfVcCountTaggedBECNs Number of frames for which the switch set the BECN bit.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.14
casfVcCountTaggedDEs Number of frames for which the switch set the DE bit.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.1.1.15

This table contains counters at the Frame Relay
endpoint of FR-ATM interworking connections. There is
an entry in this table corresponding to each entry in
casfVcEndptTable.

casfVcIwfCountEntry row .1.3.6.1.4.1.9.9.112.1.4.2.1

A set of counters at the Frame Relay endpoint of a
FR-ATM interworking connection.

Indexes

IF-MIBifIndex casfVcEndptDlci

Column	Syntax	OID
casfVcIwfCountInUnknownProts Frames received with unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.2.1.1
casfVcIwfCountOutUnknownProts Outbound frames that were not transmitted because they contained an unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.2.1.2
casfVcIwfCountReassemblyTimeouts The number of frames which could not be completely reassembled due to a reassembly timeout, and were thus discarded before being transmitted on this connection.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.2.1.3
casfVcIwfCountLengthErrors The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU trailer length fields did not match the actual PDU length, and were thus discarded.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.2.1.4
casfVcIwfCountCrcErrors The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU had CRC errors, and were thus discarded.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.2.1.5
casfVcIwfCountTotalDiscardFrames The number of frames intended to be transmitted on this connection that were discarded due to any reason including those described in other objects in this table (e.g., frames that were discarded because insufficient bu…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.112.1.4.2.1.6

This table provides mapping from a DLCI on a Frame
Relay interface to a VPI/VCI on an internal ATM
interface.

casfFAMapEntry row .1.3.6.1.4.1.9.9.112.1.5.1.1

Given the ifIndex of a frame relay interface, and a DLCI on
that interface, this entry provides the ifIndex and
VPI/VCI on the corresponding internal atm interface.

Indexes

IF-MIBifIndex casfFAMapDlci

Column	Syntax	OID
casfFAMapDlci The DLCI value.	DlciValue Type Constraints: range: 0..4194303	.1.3.6.1.4.1.9.9.112.1.5.1.1.1
casfFAMapInternalAtmInterface The ifIndex of the internal ATM interface to which this DLCI is mapped.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.112.1.5.1.1.2
casfFAMapInternalAtmVpi The VPI value to which this DLCI is mapped.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.9.9.112.1.5.1.1.3
casfFAMapInternalAtmVci The VCI value to which this DLCI is mapped.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.112.1.5.1.1.4

This table provides mapping from an atmVclEntry on an
internal ATM internal to a casfVcEndptEntry on a  
Frame Relay interface.

casfAFMapEntry row .1.3.6.1.4.1.9.9.112.1.5.2.1

Given the ifIndex of an internal ATM interface, and
VPI/VCI, provides the ifIndex of a Frame Relay
interface and DLCI, if such mapping exists.

The value of ifType for an internal ATM interface is
propVirtua…

Indexes

IF-MIBifIndex casfAFMapAtmVpi casfAFMapAtmVci

Column	Syntax	OID
casfAFMapAtmVpi The VPI value of the Virtual Channel Link (VCL) on the ATM interface.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.9.9.112.1.5.2.1.1
casfAFMapAtmVci The VCI value of the Virtual Channel Link (VCL) on the ATM interface.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.112.1.5.2.1.2
casfAFMapFrIndex The ifIndex of the frame relay interface that this VCL maps to.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.112.1.5.2.1.3
casfAFMapFrDlci The DLCI on the frame relay interface that this VCL maps to.	DlciValue Type Constraints: range: 0..4194303	.1.3.6.1.4.1.9.9.112.1.5.2.1.4