ARICENT-ISS-EXT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
50

issExtRateCtrlTable

table
.1.3.6.1.4.1.2076.81.8.1.1 · 1 row entry · 9 columns
Open in standard view
Uses the aricent variant from /opt/observium/mibs/aricent.
Command help
Walk issExtRateCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ARICENT-ISS-EXT-MIB' -M '/opt/observium/mibs/aricent:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ARICENT-ISS-EXT-MIB::issExtRateCtrlTable' 
A table to control the rate limiting parameters 
either for the entire switch or for each physical and port-channel
interface in the switch.
issExtRateCtrlEntry row .1.3.6.1.4.1.2076.81.8.1.1.1
An entry appears in this table for each physical and port-channel
interface in the switch.
Indexes
Column Syntax OID
issExtRateCtrlIndex
The interface index for which the configuration in this
entry applies.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.2076.81.8.1.1.1.1
issExtRateCtrlDLFLimitValue
Allows to configure the limiting value for the maximum number
of dlf packets that can be transmitted per second over this interface.
Setting this object to the value zero disables rate limiting for
Destination lookup f…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.2076.81.8.1.1.1.2
issExtRateCtrlBCASTLimitValue
Allows to configure the limiting value for the maximum number
of broadcast packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for Broadcast pac…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.2076.81.8.1.1.1.3
issExtRateCtrlMCASTLimitValue
Allows to configure the limiting value for the maximum number
of multicast packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for Multicast pac…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.2076.81.8.1.1.1.4
issExtRateCtrlPortRateLimit
Configures interface Rate Limit (Packet that can be transferred
on a port at a particular second).

This object's value will take effect on the interface speed. Based
on the operating speed of the port, th…
Integer32r/w
Constraints:
range: 0-80000000
 .1.3.6.1.4.1.2076.81.8.1.1.1.5
issExtRateCtrlPortBurstSize
Configures interface Burst Pkt Rate. (Packet Burst that can be
transferred on a port at a particular second)

This object's value will take effect on the interface speed. Based
on the operating speed of th…
Integer32r/w
Constraints:
range: 0-80000000
 .1.3.6.1.4.1.2076.81.8.1.1.1.6
issExtDefaultRateCtrlStatus
Allows to configure the per port status of storm control feature.
when value is set as enabled, the packet rates for Broadcast,
Multicast and Dlf packets will be set to default values. when
disabled, they will be set to…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.2076.81.8.1.1.1.7
issExtRateCtrlPortInputRestoreFilter
Object is used to restore rate limit input config
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.2076.81.8.1.1.1.8
issExtRateCtrlPortInputRateLimit
Configures interface Input Rate Limit.
This object configures the input rate limit. The default value for the object is disabled.
Integer32r/w
Constraints:
range: 0-1000
 .1.3.6.1.4.1.2076.81.8.1.1.1.9

issExtL2FilterTable

table
.1.3.6.1.4.1.2076.81.8.2.1 · 1 row entry · 17 columns
Open in standard view
Uses the aricent variant from /opt/observium/mibs/aricent.
Command help
Walk issExtL2FilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ARICENT-ISS-EXT-MIB' -M '/opt/observium/mibs/aricent:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ARICENT-ISS-EXT-MIB::issExtL2FilterTable' 
A table to configure L2 filter rules in the system.
issExtL2FilterEntry row .1.3.6.1.4.1.2076.81.8.2.1.1
Each entry in this table is a L2 filter rule.

Index to the table is the L2 filter number.
Indexes
Column Syntax OID
issExtL2FilterNo
L2 Filter rule number.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.2076.81.8.2.1.1.1
issExtL2FilterPriority
The priority of the L2 filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> All the filter rules result in 'allow'ing the packet
…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.2076.81.8.2.1.1.2
issExtL2FilterEtherType
The value in the Type/Len field of a frame that will
be matched to trigger this filter. The default value of
this object is '0'. When this object is SET with the default
value, frames are not matched for the value in th…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.2076.81.8.2.1.1.3
issExtL2FilterProtocolType
Specifies the non IP protocol type to be filtered.
aarp | amber | dec-spanning | decnet-iv |
diagnostic | dsm |etype-6000 | etype-8042 |
lat | lavc-sca | mop-console | mop-dump |
msdos | mumps | netbios | vines-echo …
Unsigned32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.2076.81.8.2.1.1.4
issExtL2FilterDstMacAddr
Destination MAC address to be matched with the packet. By Default, the
Destination Mac Address will be zero which means dont care condition ie)
any Dst Mac Address .
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.2076.81.8.2.1.1.5
issExtL2FilterSrcMacAddr
Source MAC address to be matched with the packet. By Default, the Source
Mac Address will be zero which means dont care condition ie) any Src Mac
address
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.2076.81.8.2.1.1.6
issExtL2FilterVlanId
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will
be treated as customer Vlan Id.
A value of '0' means, this object is unused. Configuring this value is not
allowed.
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.2076.81.8.2.1.1.7
issExtL2FilterInPortList
Specifies the complete set of ports over which this filter is applied
for packets ingress at ports in this list.
If the In port list is '0', the filter rule is applicable for the
incoming packets on all ports.
Even th…
PortListr/w .1.3.6.1.4.1.2076.81.8.2.1.1.8
issExtL2FilterAction
Specifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be forwarded according
to the forwarding rules.
If the action is 'drop', the packet will be discarded.
Enumerationr/w
Enumerated Values:
1allow
2drop
 .1.3.6.1.4.1.2076.81.8.2.1.1.9
issExtL2FilterMatchCount
Number of times this filter is matched.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.81.8.2.1.1.10
issExtL2FilterStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.2076.81.8.2.1.1.11
issExtL2FilterOutPortList
Specifies the complete set of ports over which this filter is applied
for packets egress at Ports in this list.
If the Out port list is '0', the filter rule is applicable for the
outgoing packets on all ports.
Even th…
PortListr/w .1.3.6.1.4.1.2076.81.8.2.1.1.12
issExtL2FilterDirection
Specifies the direction of this filter to be applied. By Default the
filter will be applied on ingress direction.
When the direction of this filter is 'in', It is applied on specified
ports of the issExtL2FilterInPortLi…
Enumerationr/w
Enumerated Values:
1in
2out
 .1.3.6.1.4.1.2076.81.8.2.1.1.13
issExtL2FilterCfiDeiBit
Specifies the CfiDei bit value in the c-vlan tag or s-vlan tag of
the packet to be applied in the filter.
Enumerationr/w
Enumerated Values:
1set
2reset
 .1.3.6.1.4.1.2076.81.8.2.1.1.14
issExtL2FilterDP
Specifies the drop precedence level to be applied in the filter.
Enumerationr/w
Enumerated Values:
1green
2yellow
3red
 .1.3.6.1.4.1.2076.81.8.2.1.1.15
issExtL2FilterDstMacAddrMask
This object specifies that the mask used to match the Destination MAC address with the packet. By Default, the Destination
Mac Address Mask will be ff:ff:ff:ff:ff:ff which means macth exactly the Dst Mac specified
addr…
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.2076.81.8.2.1.1.16
issExtL2FilterSrcMacAddrMask
This object specifies that the mask used to match the Source MAC address with the packet. By Default, the Source
Mac Address Mask will be ff:ff:ff:ff:ff:ff which means macth exactly the Src Mac specified
address
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.2076.81.8.2.1.1.17

issExtL3FilterTable

table
.1.3.6.1.4.1.2076.81.8.3.1 · 1 row entry · 24 columns
Open in standard view
Uses the aricent variant from /opt/observium/mibs/aricent.
Command help
Walk issExtL3FilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ARICENT-ISS-EXT-MIB' -M '/opt/observium/mibs/aricent:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ARICENT-ISS-EXT-MIB::issExtL3FilterTable' 
A table to configure L3 filter rules in the system.
issExtL3FilterEntry row .1.3.6.1.4.1.2076.81.8.3.1.1
Each entry in this table is a L3 filter rule.
Index to the table is L3 filter number.
Indexes
Column Syntax OID
issExtL3FilterNo
L3 Filter rule number.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.2076.81.8.3.1.1.1
issExtL3FilterPriority
The priority of the filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> All the filter rules result in 'allow'ing the packet
Higher value o…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.2076.81.8.3.1.1.2
issExtL3FilterProtocol
The type of protocol to be checked against the packet. The
default value is 255. If the value is 255, it means that the
protocol type can be anything and it will not be checked to
decide the action.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.2076.81.8.3.1.1.3
issExtL3FilterMessageType
The message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in issExtL3FilterAction.
The default value is 255. It mea…
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.2076.81.8.3.1.1.4
issExtL3FilterMessageCode
The message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in issExtL3FilterAction.
The default value is 255. It mea…
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.2076.81.8.3.1.1.5
issExtL3FilterDstIpAddr
Destination IP address to be matched with the packet.
This object is valid only if the 'issExtFilterType' is 'l3filter'.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.81.8.3.1.1.6
issExtL3FilterSrcIpAddr
Source IP address to be matched with the packet.
This object is valid only if the 'issExtFilterType' is 'l3filter'.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.81.8.3.1.1.7
issExtL3FilterDstIpAddrMask
The IP subnet mask for Destination IP address.
This object is valid only if the 'issExtFilterType' is 'l3filter'.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.81.8.3.1.1.8
issExtL3FilterSrcIpAddrMask
The IP subnet mask for Source IP address.
This object is valid only if the 'issExtFilterType' is 'l3filter'.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.81.8.3.1.1.9
issExtL3FilterMinDstProtPort
The minimum port in the destination port range. Please note
these ports are the TCP / UDP ports.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.81.8.3.1.1.10
issExtL3FilterMaxDstProtPort
The maximum port in the destination port range. Please note
these ports are the TCP / UDP ports.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.81.8.3.1.1.11
issExtL3FilterMinSrcProtPort
The minimum port in the source port range. Please note
these ports are the TCP / UDP ports.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.81.8.3.1.1.12
issExtL3FilterMaxSrcProtPort
The maximum port in the source port range. Please note
these ports are the TCP / UDP ports.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.81.8.3.1.1.13
issExtL3FilterInPortList
Specifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.
If the incoming port list is '0', the filter rule is applicable for all the
incoming ports.
By default inport li…
PortListr/w .1.3.6.1.4.1.2076.81.8.3.1.1.14
issExtL3FilterOutPortList
Specifies the complete set of ports over which if the packet goes out,
this filter rule will be applicable.
If the outgoing port list is '0', the filter rule is applicable for all the
outgoing packets in all ports.
By…
PortListr/w .1.3.6.1.4.1.2076.81.8.3.1.1.15
issExtL3FilterAckBit
The TCP ACK bit to be checked against the packet. The default
value is 'any'(3). It means that ACK bit will not be checked
to decide the action.
Enumerationr/w
Enumerated Values:
1establish
2notEstablish
3any
 .1.3.6.1.4.1.2076.81.8.3.1.1.16
issExtL3FilterRstBit
The TCP RST bit to be checked against the packet. The default
value is 'any'(3). It means that RST bit will not be checked to
decide the action.
Enumerationr/w
Enumerated Values:
1set
2notSet
3any
 .1.3.6.1.4.1.2076.81.8.3.1.1.17
issExtL3FilterTos
The IP TOS bit to be checked against the packet. This is a
single byte integer of which the last three bits (least
significant bits) indicate Delay, Throughput and Reliability
i.e 'uuuuudtr', u-unused, d-delay, t-thr…
Integer32r/w
Constraints:
range: 0-8
 .1.3.6.1.4.1.2076.81.8.3.1.1.18
issExtL3FilterDscp
The IP Dscp value to be checked against the packet.
A value of '-1' means, the Dscp Field becomes dont care.
Integer32r/w
Constraints:
range: -1-63
 .1.3.6.1.4.1.2076.81.8.3.1.1.19
issExtL3FilterDirection
Specifies the direction of this filter to be applied. By Default the
filter will be applied on ingress direction.
When the direction of this filter is 'in', It is applied on specified
ports of the issExtL3FilterInPortLi…
Enumerationr/w
Enumerated Values:
1in
2out
 .1.3.6.1.4.1.2076.81.8.3.1.1.20
issExtL3FilterAction
Specifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be sent to the
ports in 'out port list'. If the out port list is '0',
the port over which the packet …
Enumerationr/w
Enumerated Values:
1allow
2drop
 .1.3.6.1.4.1.2076.81.8.3.1.1.21
issExtL3FilterMatchCount
Number of times this filter is matched.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.81.8.3.1.1.22
issExtL3FilterStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.2076.81.8.3.1.1.23
issExtL3FilterSynBit
The TCP SYN bit to be checked against the packet. The default
value is 'any'(3). It means that SYN bit will not be checked to
decide the action.
Enumerationr/w
Enumerated Values:
1set
2notSet
3any
 .1.3.6.1.4.1.2076.81.8.3.1.1.24