ALLIEDTELESYN-MIB Table View

The table of AT8948 fanAndPsPsuStatusTable. Each entry in the table
represents the status of one of the power supplies in AT8948 system.
Each power supply has its own board ID.

fanAndPsPsuStatusEntry row .1.3.6.1.4.1.207.8.4.4.3.1.11.1

A single entry of AT8948 fanAndPsPsuStatusTable, indexed by
fanAndPsPsuNumber field.

Indexes

fanAndPsPsuNumber

Column	Syntax	OID
fanAndPsPsuNumbermandatory The PSU board identity for which this entry holds. If the system consists only of a single PSU board, only one entry will appear in the table, whose index is 1.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.3.1.11.1.1
fanAndPsPsuPresentmandatory The PSU present state, displayed as 'yes' if present, or 'no' if absent.	Enumeration Enumerated Values: 0 yes 1 no	.1.3.6.1.4.1.207.8.4.4.3.1.11.1.2
fanAndPsPsuTypemandatory The PSU type, displayed as AC, or DC, or FAN, or NOT PRESENT.	Enumeration Enumerated Values: 0 ac 1 dc 2 fan 3 not-present 4 not-supported	.1.3.6.1.4.1.207.8.4.4.3.1.11.1.3
fanAndPsPsuFanmandatory The PSU fan status, displayed as OK, or FAIL, or NOT PRESENT.	Enumeration Enumerated Values: 0 ok 1 fail 2 not-present 3 not-supported	.1.3.6.1.4.1.207.8.4.4.3.1.11.1.4
fanAndPsPsuTemperaturemandatory The PSU temperature, displayed as GOOD, or HIGH, or NOT PRESENT, or NOT SUPPORTED.	Enumeration Enumerated Values: 0 good 1 high 2 not-present 3 not-supported	.1.3.6.1.4.1.207.8.4.4.3.1.11.1.5
fanAndPsPsuPowermandatory The PSU power status, displayed as GOOD, or BAD, or NOT PRESENT or NOT SUPPORTED.	Enumeration Enumerated Values: 0 good 1 bad 2 not-present 3 not-supported	.1.3.6.1.4.1.207.8.4.4.3.1.11.1.6

The table of SwitchBlade sysTemperature. Each entry in the table
represents temperature monitoring from one of the CPU cards which
may be present in the SwitchBlade system.

sbTempEntry row .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1

A single entry of SwitchBlade sysTemperature

Indexes

sbTempIndex

Column	Syntax	OID
sbTempIndexmandatory The board for which this temperature entry holds. If the system consists only of a single CPU board, only one entry will appear in the table, whose index is master(1).	Enumeration Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.1
sbTempActualTemperaturemandatory The actual SwitchBlade temperature. This temperature is measured within the SwitchBlade CPU, and is sampled at 1 second intervals.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.2
sbTempFixedThresholdStatusmandatory The temperature status with regard to the fixed temperature threshold. The value of the fixed temperature threshold is set at 90 degrees C. This variable represents whether the actual temperature is above the threshold …	Enumeration Enumerated Values: 1 normal 2 crossover	.1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.3
sbTempSettableThresholdStatusmandatory The temperature status with regard to the settable temperature threshold. The value of the settable temperature threshold is set by management intervention. This variable represents whether the actual temperature is abo…	Enumeration Enumerated Values: 1 normal 2 crossover 3 undefined	.1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.4
sbTempSettableThresholdmandatory The value of the settable temperature threshold. This can be set independently for each temperature entry. The value of this threshold is only valid when sbTempSettableThresholdStatus is not set to undefined(3).	Integer32r/w Constraints: range: 30-100	.1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.5

The table of Ethernet interfaces.

ethIntEntry row .1.3.6.1.4.1.207.8.4.4.4.23.1.1

A single entry in the Ethernet interfaces table.

Indexes

ethIntIndex

Column	Syntax	OID
ethIntIndexmandatory The ifIndex of the Ethernet interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.23.1.1.1
ethIntBoardIndexmandatory The index in the arBoardTable of the board on which this Ethernet interface resides. If this Ethernet interface is not found, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.23.1.1.2
ethIntBoardPositionmandatory The position on this Ethernet interface's board of this Ethernet interface. If this Ethernet interface is not found, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.23.1.1.3
ethIntDuplexModemandatory The duplex mode of this Ethernet interface. The value unknown is returned when the interface cannot or has not yet made a determination of its duplex mode, or when the interface cannot be found.	Enumeration Enumerated Values: 1 full-duplex 2 half-duplex 3 unknown	.1.3.6.1.4.1.207.8.4.4.4.23.1.1.4

The table of call details parameters.

ccDetailsEntry row .1.3.6.1.4.1.207.8.4.4.4.37.1.1

A single entry of ISDN call details. This contains the
parameters of a single ISDN call details.

Indexes

ccDetailsIndex

Column	Syntax	OID
ccDetailsIndexmandatory The index of the call details entry in the call details table. When an entry is created in this table, the index does not have to be written. However, to reference the values that are written, an unused index must be fo…	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.1
ccDetailsNamemandatory The name of the ISDN call details. This must be unique for all ISDN call details, when comparisons are done ignoring the case of letters. Valid characters in the ISDN call name include 0-9, a-z, A-Z and '_'. A name cons…	OctetStringr/w Constraints: range: 0-15	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.2
ccDetailsRemoteNamemandatory The remote ISDN call name. This name can be referenced by certain other call details parameters related with setting up the Q.931 SETUP message for outgoing calls, or searching for calls for incoming calls. Valid charac…	OctetStringr/w Constraints: range: 0-15	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.3
ccDetailsCalledNumbermandatory The number called when this call details is activated. The number should include all telephone network access codes, country codes and area codes required to make a call from the particular ISDN interface. Setting this …	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.4
ccDetailsCallingNumbermandatory The number used as the calling number when this call is activated. The calling number can optionally be placed in the outgoing SETUP message.	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.5
ccDetailsAlternateNumbermandatory The number called when all retries with the main called number have failed. In this event, the router tries once with the alternate number, then checks the ccDetailsKeepup object to determine whether to try again with t…	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.6
ccDetailsEnabledmandatory Whether this ISDN call is enabled or disabled for incoming and outgoing calls. If the call details entry is disabled, all existing active calls based on this call details entry are left active.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.7
ccDetailsDirectionmandatory The direction for which calls may be made or received using this call details entry.	Enumerationr/w Enumerated Values: 1 in-only 2 out-only 3 both	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.8
ccDetailsPrecedencemandatory The precedence of this call details entry in the event of call collision. Call collision occurs when an incoming call for a given details entry is detected while an outgoing call is waiting to complete. This object conf…	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.9
ccDetailsHoldupTimemandatory The time, in seconds, that active calls created from this call details should be held up after initial activation. The call will be held up for at least this time, unless cleared from the network. Thus, for example, PPP…	Integer32r/w Constraints: range: 0-7200	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.10
ccDetailsPreferredIfIndexmandatory The ifIndex of an ISDN interface on this router which is the preferred ISDN interface on which to make an outgoing call using this call details entry. The ifIndex, if not 0, should reference the ifEntry which contains i…	InterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.11
ccDetailsRequiredIfIndexmandatory The ifIndex of an ISDN interface on this router which is the required ISDN interface on which to make an outgoing call using this call details entry. The ifIndex, if not 0, must reference the ifEntry which contains info…	InterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.12
ccDetailsPrioritymandatory The priority of calls generated from this call details entry. The priority determines whether calls can be bumped for higher priority calls. The value of priority falls into ranges: 0-19 - call bumped by incoming or out…	Integer32r/w Constraints: range: 0-99	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.13
ccDetailsRetryT1mandatory The time in seconds between retries of calls generated from this call details entry.	Integer32r/w Constraints: range: 5-120	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.14
ccDetailsRetryN1mandatory The number of retries in a retry group for calls generated from this call details entry. Note that the default value means that by default the call will not be retried.	Integer32r/w Constraints: range: 0-10	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.15
ccDetailsRetryT2mandatory The time in seconds between retry groups for retries of calls generated from this call details entry.	Integer32r/w Constraints: range: 300-1200	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.16
ccDetailsRetryN2mandatory The number of retry groups for calls generated from this call details entry. Note that the default value means that by default no retry groups will be attempted.	Integer32r/w Constraints: range: 0-5	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.17
ccDetailsKeepupmandatory A flag indicating whether calls generated from this call details entry should be kept up always. Inspection of this flag takes place when a call is cleared from an external source. If set to 'yes', the call will be retr…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.18
ccDetailsOutSetupClimandatory The CLI information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no CLI information in placed in the SETUP message. The value 'calling' mean…	Enumerationr/w Enumerated Values: 1 off 2 calling 3 interface 4 nonumber	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.19
ccDetailsOutSetupUsermandatory The user-user information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no user-user information in placed in the SETUP message. The value 'l…	Enumerationr/w Enumerated Values: 1 off 2 local 3 remote	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.20
ccDetailsOutSetupCalledSubmandatory The called subaddress information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no called subaddress information in placed in the SETUP messa…	Enumerationr/w Enumerated Values: 1 off 2 local 3 remote	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.21
ccDetailsOutSubaddressmandatory This object gives a way to override the called subaddress information placed into outgoing SETUP messages when this call details is used to generate an outgoing call, as given by the ccDetailsOutSetupCalledSub object. T…	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.22
ccDetailsCallbackmandatory A flag indicating whether or not to call back the caller when an incoming call is generated from this call details entry. If set to 'yes', the incoming call will be cleared, and after a short delay, an outgoing call wil…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.23
ccDetailsCallbackDelaymandatory The time, in tenths of a second, which the router will wait after clearing an incoming call whose call details entry specified that the caller should be called back before making the return call. The purpose of this obj…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.24
ccDetailsInSetupCalledSubSearchmandatory Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the called subaddress information in the incoming SETUP message. The value 'off' means that th…	Enumerationr/w Enumerated Values: 1 off 2 local 3 remote	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.25
ccDetailsInSetupUserSearchmandatory Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the user-user information in the incoming SETUP message. The value 'off' means that this call …	Enumerationr/w Enumerated Values: 1 off 2 local 3 remote	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.26
ccDetailsInSetupCliSearchmandatory Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the calling number information in the incoming SETUP message. The value 'off' means that this …	Enumerationr/w Enumerated Values: 1 off 2 on 3 list	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.27
ccDetailsInSetupCliSearchListmandatory If the ccDetailsInSetupCliSearch object is set to 'list', this object gives the index of the CLI list to search. The value of CLI list indices is 1..100. The value 0 is returned when the ccDetailsInSetupCliSearch object…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.28
ccDetailsInAnyFlagmandatory Determines whether this call details entry will match any incoming call. After all searched for incoming calls have been carried out based on called subaddress, user-user information and calling number, a search is carr…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.29
ccDetailsInSetupCalledSubCheckmandatory Determines whether to perform a check when an incoming call matches this call details entry based on the contents of the called subaddress information in the incoming SETUP message. The value 'off' means that the check …	Enumerationr/w Enumerated Values: 1 off 2 local 3 remote	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.30
ccDetailsInSetupUserCheckmandatory Determines whether to perform a check when an incoming call matches this call details entry based on the contents of the user-user information in the incoming SETUP message. The value 'off' means that the check is not c…	Enumerationr/w Enumerated Values: 1 off 2 local 3 remote	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.31
ccDetailsInSetupCliCheckmandatory Determines whether to perform a check and which check to perform when an incoming call matches this call details entry based on the contents of the calling number information in the incoming SETUP message. The value 'of…	Enumerationr/w Enumerated Values: 1 off 2 present 3 required	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.32
ccDetailsInSetupCliCheckListmandatory If the ccDetailsInSetupCliCheck object is set to 'present' or 'required', this object gives the index of the CLI list to check against. The value of CLI list indices is 1..100. The value 0 means that no list to check ag…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.33
ccDetailsUserTypemandatory The type of user of this call. The value 'attach' means that users have to attach to this call before the call can be used for outgoing or incoming calls. The value 'ppp' means that for incoming calls only dynamic PPP i…	Enumerationr/w Enumerated Values: 1 attach 2 ppp	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.34
ccDetailsLoginTypemandatory The type of login for calls generated using this call details entry, for incoming calls only. Incoming calls can be configured to go through a logging in phase before the call is brought up. This object defines which lo…	Enumerationr/w Enumerated Values: 1 none 2 userdb 3 radius 4 pap-tacacs 5 chap 6 pap-radius 7 tacacs 8 all	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.35
ccDetailsUsernamemandatory The source of the username when the ccDetailsLoginType object has a value of 'userdb', 'radius', 'tacacs' or 'all'. The value 'none' means no username is defined. The value 'cli' means take the username from the callin…	Enumerationr/w Enumerated Values: 1 none 2 cli 3 calledsub 4 useruser 5 callname	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.36
ccDetailsPasswordmandatory The source of the password when the ccDetailsLoginType object has a value of 'userdb', 'radius', 'tacacs' or 'all'. The value 'none' means no password is defined. The value 'cli' means take the password from the callin…	Enumerationr/w Enumerated Values: 1 none 2 cli 3 calledsub 4 useruser 5 callname	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.37
ccDetailsBumpDelaymandatory The time, in tenths of a second, which the router will wait after clearing an existing call which has been bumped to make way for a call based on this call details entry.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.38
ccDetailsDataRatemandatory The data rate to use for active calls based on this call details entry. The actual data rate for outgoing calls is determined by both this object and the data rate parameter for the Q.931 interface chosen for the call. …	Enumerationr/w Enumerated Values: 1 rate-64k 2 rate-56k	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.39
ccDetailsPppTemplatemandatory The PPP template to use when creating dynamic PPP interfaces for calls generated from this call details entry. The value 33 represents a default PPP template, the values 1 to 32 represent PPP templates that are currentl…	Integer32r/w Constraints: range: 1-33	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.40
ccDetailsUserModulemandatory The module ID of the user module currently attached to this ISDN call details entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.41
ccDetailsNumberAttachmentsmandatory The number of attachments from the user module currently attached to this call details entry. The ccAttachmentsTable gives the actual attachments for each call details entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.1.1.42

The table of CLI list entries.

ccCliListEntry row .1.3.6.1.4.1.207.8.4.4.4.37.2.1

A single entry in the CLI list table. This contains a single number, as well as index information.

Indexes

ccCliListListIndex ccCliListEntryIndex

Column	Syntax	OID
ccCliListListIndexmandatory The index of the CLI list. CLI lists from 1 to 100 are defined in the router.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.207.8.4.4.4.37.2.1.1
ccCliListEntryIndexmandatory The index of the CLI list entry within the CLI list. The minimum CLI list entry is 1. CLI lists are unlimited in length, although internal memory requirements could result in failure to create a given entry. When creati…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.2.1.2
ccCliListNumbermandatory The number for this CLI list entry. Setting the number to a zero length string removes the entry from the CLI list, with consequent reshuffling of CLI entry indices. Thus the easiest way to delete an entire CLI list is …	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.207.8.4.4.4.37.2.1.3

The table of ISDN active calls.

ccActiveCallEntry row .1.3.6.1.4.1.207.8.4.4.4.37.3.1

A single entry in the active call table.

Indexes

ccActiveCallIndex

Column	Syntax	OID
ccActiveCallIndexmandatory The index of the active call. There are 128 possible active calls in the router simultaneously.	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.1
ccActiveCallDetailsIndexmandatory The index of the call details entry which generated this active call. Thus the index into the ccDetailsTable for this call.	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.2
ccActiveCallIfIndexmandatory The interface index of the interface on which this active call is being made or received. A value of zero indicates that the active has not yet had an interface assigned to it. The ifEntry indexed by this object is the …	InterfaceIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.3
ccActiveCallDataRatemandatory The data rate in use for this active call. This is determined by the call details setting of data rate, the ISDN interface setting for data rate, and the contents of the bearer capability information in the incoming SET…	Enumeration Enumerated Values: 1 rate-64k 2 rate-56k	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.4
ccActiveCallStatemandatory The state of this active call. The value 'null' indicates that this active call does not actually exist, in other words it is in the process of being created or destroyed. The value 'off' means that the active call is j…	Enumeration Enumerated Values: 1 null 2 off 3 try 4 on 5 wait 6 await1	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.5
ccActiveCallDirectionmandatory The direction of this active call. The value 'in' indicates that this active call is an incoming call, the value 'out' indicates that the active call is an outgoing call. The value 'undefined' indicates that the active …	Enumeration Enumerated Values: 1 in 2 out 3 undefined	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.6
ccActiveCallUserModulemandatory The module ID of the user module attached to this ISDN active call.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.7
ccActiveCallUserInstancemandatory The instance of the user module attached to this ISDN active call.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.8
ccActiveCallBchannelIndexmandatory The B channel number for this active entry. BRI interfaces have B channels in the range 1..2, PRI interfaces have B channels in the range 1..31, excluding a channel which is the D channel. A value of 0 for this entry me…	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.207.8.4.4.4.37.3.1.9

The table of ISDN call log entries.

ccCallLogEntry row .1.3.6.1.4.1.207.8.4.4.4.37.4.1

A single entry in the ISDN call log table.

Indexes

ccCallLogIndex

Column	Syntax	OID
ccCallLogIndexmandatory The index of the call log entry. Since the call log table is dynamic, there is no guarantee that this index will continue to refer to the same log entry over time.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.1
ccCallLogNamemandatory The name of the call details entry which generated the active call for which this is the log entry.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.2
ccCallLogStatemandatory The state of the log entry. The value 'initial' means that the call is being established. The value 'active' means that the call is currently established. The value 'disconnected' means that the call was disconnected af…	Enumeration Enumerated Values: 1 initial 2 active 3 disconnected 4 cleared	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.3
ccCallLogTimeStartedmandatory A string in the format 'dd-mmm-yyyy hh:mm:ss' which gives the start time of the call for which this is the log entry. If the call never reached or has not yet reached the active state, this object will be a zero-length …	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.4
ccCallLogDirectionmandatory The direction of the call for which this is the log entry.	Enumeration Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.5
ccCallLogDurationmandatory The duration in seconds, of the call for which this is the log entry. A value of 0 in this field means either that the call has just started, that the call was cleared before becoming established, or that the call is st…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.6
ccCallLogRemoteNumbermandatory For incoming calls, the calling number, if this was made available in the SETUP message. For outgoing calls, the number dialed. If the number was not available, this object is a zero length string.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.37.4.1.7

The table of call detail attachment entries.

ccAttachmentEntry row .1.3.6.1.4.1.207.8.4.4.4.37.5.1

A single entry in the attachment table.

Indexes

ccAttachmentDetailsIndex ccAttachmentEntryIndex

Column	Syntax	OID
ccAttachmentDetailsIndexmandatory The index of the call details entry to which this attachment entry belongs.	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.207.8.4.4.4.37.5.1.1
ccAttachmentEntryIndexmandatory The index of the attachment entry within the attachment list.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.5.1.2
ccAttachmentActiveCallIndexmandatory The index of the active call for this attachment. A value of 0 indicates that there is currently no active call for this attachment. A value of 1 to 128 references the active call currently in place for this attachment.	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.207.8.4.4.4.37.5.1.3
ccAttachmentUserInstancemandatory The instance of the user module attached to the ISDN active call for this attachment. This object should return the same value as the object ccActiveCallUserInstance for the active call indexed by ccAttachmentActiveCall…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.5.1.4

The table of B channel attachment entries.

ccBchannelEntry row .1.3.6.1.4.1.207.8.4.4.4.37.6.1

A single entry in the B channel attachment table.

Indexes

ccBchannelIfIndex ccBchannelChannelIndex

Column	Syntax	OID
ccBchannelIfIndexmandatory The interface index of the interface which this B channel entry is on. The ifEntry indexed by this object is the ifEntry for the entire ISDN interface, not the ifEntry for the active call's B channel.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.1
ccBchannelChannelIndexmandatory The B channel number for this B channel entry. BRI interfaces have B channels in the range 1..2, PRI interfaces have B channels in the range 1..31, excluding a channel which is the D channel.	Integer32 Constraints: range: 1-31	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.2
ccBchannelAllocatedmandatory A flag indicating whether this B channel is actually allocated to a call or not.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.3
ccBchannelCallTypemandatory The type of call on this B channel. If the B channel is not allocated, the call type will be undefined.	Enumeration Enumerated Values: 1 undefined 2 data 3 voice 4 x25	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.4
ccBchannelActiveCallIndexmandatory The index of the active call which is currently attached to this B channel. If the value of this object is 0 the channel is either not allocated, or is not allocated to a data call.	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.5
ccBchannelPrioritymandatory The priority of the call which has this B channel allocated to it. This is in the range 0..99 for data calls, 150 for voice calls and 200 for emergency voice calls. A B channel which is not allocated will have a priorit…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.6
ccBchannelDirectionmandatory The direction of the call which has this B channel allocated to it. If this B channel is not allocated the value will be 'unallocated'.	Enumeration Enumerated Values: 1 in 2 out 3 unallocated	.1.3.6.1.4.1.207.8.4.4.4.37.6.1.7

The table of BRI interfaces.

briIntEntry row .1.3.6.1.4.1.207.8.4.4.4.41.1.1

A single entry in the BRI interfaces table.

Indexes

briIntIndex

Column	Syntax	OID
briIntIndexmandatory The ifIndex of the BRI interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.41.1.1.1
briIntBoardIndexmandatory The index in the arBoardTable of the board on which this BRI interface resides.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.41.1.1.2
briIntBoardPositionmandatory The position on this BRI interface's board of this BRI interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.41.1.1.3
briIntModemandatory The mode of operation of this BRI interface. The value isdn means that the entire interface is operating as an ISDN interface, the value tdm means that the entire interface is operating as TDM groups and the value mixed…	Enumeration Enumerated Values: 1 isdn 2 tdm 3 mixed	.1.3.6.1.4.1.207.8.4.4.4.41.1.1.4
briIntTdmChannelMapmandatory A bit map of the channels in the BRI interface which are dedicated to TDM. Channel B1 has channel map value of 1, channel B2 has a channel map value of 2.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.41.1.1.5
briIntIsdnChannelMapmandatory A bit map of the channels in the BRI interface which are dedicated to ISDN. Channel B1 has channel map value of 1, channel B2 has a channel map value of 2.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.41.1.1.6

The table of channels on BRI interfaces.

briChanEntry row .1.3.6.1.4.1.207.8.4.4.4.41.2.1

A single entry in the BRI channels table.

Indexes

briChanIntIndex briChanChannelIndex

Column	Syntax	OID
briChanIntIndexmandatory The ifIndex of the BRI interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.41.2.1.1
briChanChannelIndexmandatory The channel index of the BRI channel. Channel B1 has index 1, channel B2 has index 2 and the D channel has index 3.	Integer32 Constraints: range: 1-3	.1.3.6.1.4.1.207.8.4.4.4.41.2.1.2
briChanModemandatory The mode of this BRI channel. The value isdn means that the channel is reserved for use in ISDN calls. The value tdm means that the channel is reserved for use by TDM. For the D channel, this object will always have the…	Enumeration Enumerated Values: 1 isdn 2 tdm 3 none	.1.3.6.1.4.1.207.8.4.4.4.41.2.1.3
briChanStatemandatory The state of this BRI channel. The value inactive means that the channel does not currently have an active user, either an ISDN call or an active TDM group. The value active means that the channel is in use, either by a…	Enumeration Enumerated Values: 1 inactive 2 active	.1.3.6.1.4.1.207.8.4.4.4.41.2.1.4

The table of PRI interfaces.

priIntEntry row .1.3.6.1.4.1.207.8.4.4.4.42.1.1

A single entry in the PRI interfaces table.

Indexes

priIntIndex

Column	Syntax	OID
priIntIndexmandatory The ifIndex of the PRI interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.1
priIntBoardIndexmandatory The index in the arBoardTable of the board on which this PRI interface resides.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.2
priIntBoardPositionmandatory The position on this PRI interface's board of this PRI interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.3
priIntModemandatory The mode of operation of this PRI interface. The value isdn means that the entire interface is operating as an ISDN interface, the value tdm means that the entire interface is operating as TDM groups and the value mixed…	Enumeration Enumerated Values: 1 isdn 2 tdm 3 mixed	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.4
priIntTdmChannelMapmandatory A bit map of the channels in the PRI interface which are dedicated to TDM. PRI channels are numbered from 0 to 31, 0 is unused, 16 (E1) or 24 (T1) is the D channel. The map values are 2 to the power of the channel numbe…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.5
priIntIsdnChannelMapmandatory A bit map of the channels in the PRI interface which are dedicated to ISDN. PRI channels are numbered from 0 to 31, 0 is unused, 16 (E1) or 24 (T1) is the D channel. The map values are 2 to the power of the channel numb…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.6
priIntTypemandatory The type of primary rate interface. E1 has 30 B + D channel, T1 has 23 B + D channel. If the value unknown is returned for this object, the exact PRI type has not yet been determined.	Enumeration Enumerated Values: 1 e1 2 t1 3 unknown	.1.3.6.1.4.1.207.8.4.4.4.42.1.1.7

The table of channels on PRI interfaces.

priChanEntry row .1.3.6.1.4.1.207.8.4.4.4.42.2.1

A single entry in the PRI channels table.

Indexes

priChanIntIndex priChanChannelIndex

Column	Syntax	OID
priChanIntIndexmandatory The ifIndex of the PRI interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.42.2.1.1
priChanChannelIndexmandatory The channel index of the PRI channel. Valid channels have indices from 1 to 31. The D channel on an E1 interface has index 16, the D channel on a T1 interface has index 24.	Integer32 Constraints: range: 1-31	.1.3.6.1.4.1.207.8.4.4.4.42.2.1.2
priChanModemandatory The mode of this PRI channel. The value isdn means that the channel is reserved for use in ISDN calls. The value tdm means that the channel is reserved for use by TDM. For the D channel, this object will usually have th…	Enumeration Enumerated Values: 1 isdn 2 tdm 3 neither	.1.3.6.1.4.1.207.8.4.4.4.42.2.1.3
priChanStatemandatory The state of this PRI channel. The value inactive means that the channel does not currently have an active user, either an ISDN call or an active TDM group. The value active means that the channel is in use, either by a…	Enumeration Enumerated Values: 1 inactive 2 active	.1.3.6.1.4.1.207.8.4.4.4.42.2.1.4

The table of load parameters, dynamic and static.

loadEntry row .1.3.6.1.4.1.207.8.4.4.4.48.1.1

A single entry of load parameters. This contains the
parameters required to perform a load from the router.

Indexes

loadIndex

Column	Syntax	OID
loadIndexmandatory There are two sets of load information, dynamic and static. The dynamic information is used once, then cleared. The static information is used whenever the dynamic information is not available. The dynamic information i…	Enumerationr/w Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.207.8.4.4.4.48.1.1.1
loadServermandatory The IP address from which load will load.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.48.1.1.2
loadDestinationmandatory The destination of the file loaded, either flash or nvs memory, or undefined.	Enumerationr/w Enumerated Values: 1 undefined 2 nvs 3 flash	.1.3.6.1.4.1.207.8.4.4.4.48.1.1.3
loadFilenamemandatory The file name of the file being loaded.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.48.1.1.4
loadDelaymandatory A delay in seconds between the initiation of the load and the start of the load. This allows for time to set up TFTP servers in cases where the terminal and TFTP server are using the same piece of equipment but will not…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.48.1.1.5

The list of install configurations for the router.

installEntry row .1.3.6.1.4.1.207.8.4.4.4.49.1.1

An entry in the list of install configurations.

Indexes

instIndex

Column	Syntax	OID
instIndexmandatory The index for the install table. There are four install configurations defined in the router, default, preferred, temporary and current. The router will attempt to use these in the order temporary, preferred, default w…	Enumeration Enumerated Values: 1 temporary 2 preferred 3 default 4 current	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.1
instRelDevicemandatory The device for the release in the install. If the device is flash the file for the release is given in instRelName. Devices none(1) or flash(3) are invalid for the default(3) release.	Enumeration Enumerated Values: 1 none 2 eprom 3 flash	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.2
instRelNamemandatory The file name for the release in the install, if the instRelDevice is flash(3). If the instRelDevice is none(1) or eprom(2), this object should be a null string.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.3
instRelMajormandatory The major release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major rele…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.4
instRelMinormandatory The minor release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major rele…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.5
instPatDevicemandatory The device for the patch in the install. The file for the patch is given in instPatName unless the device is none(1).	Enumeration Enumerated Values: 1 none 3 flash 4 nvs	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.6
instPatNamemandatory The file name for the patch in the install.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.7
instRelInterimmandatory The interim release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major re…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.8
instRelExistsmandatory Indicates if the release file exists or not. true(1) means it exists, false(2) means it doesn't.	Enumeration Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.9
instPatExistsmandatory Indicates if the patch file exists or not. true(1) means it exists, false(2) means it doesn't	Enumeration Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.207.8.4.4.4.49.1.1.10

The table of descriptions of events in the install history of
the router.

installHistoryEntry row .1.3.6.1.4.1.207.8.4.4.4.49.2.1

A single line describing part of the install history of the
router.

Indexes

instHistIndex

Column	Syntax	OID
instHistIndexmandatory The index of this event in the install history. Indices run from 1 to the maximum number. The maximum number is not available as a managed object so this table will have to be traversed in order to find out how large it…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.2.1.1
instHistLinemandatory A line of text describing a single event in the install history of the router.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.49.2.1.2

The list of release licences in the router.

licenceEntry row .1.3.6.1.4.1.207.8.4.4.4.49.4.1

An entry in the list of release licences.

Indexes

licenceIndex

Column	Syntax	OID
licenceIndexmandatory A unique licence index. Licence indices are recalculated every time the router reboots to reflect the current licences on the router. As licences are added, new indices are allocated to the new licences.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.1
licenceStatusmandatory The status of the file. When read, this object will always return a value of ok(1), since the object will not exist if the value is deleting(2). Write the value deleting(2) to this object to delete the file.	Enumerationr/w Enumerated Values: 1 ok 2 deleting	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.2
licenceReleasemandatory The file name for the release whose licence this is.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.3
licenceMajormandatory The major release number for the release whose licence this is.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.4
licenceMinormandatory The minor release number for the release whose licence this is.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.5
licencePasswordmandatory The password for this release. The password is a string of hex digits.	OctetStringr/w Constraints: range: 12-12	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.6
licenceExpirymandatory A human-readable string that gives the expiry date of this licence.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.7
licenceInterimmandatory The interim release number for the release whose licence this is.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.49.4.1.8

A list of all the files in the router's non-volatile storage.

fileEntry row .1.3.6.1.4.1.207.8.4.4.4.56.1.1

An entry in the list of files containing information about a
single file in the router.

Indexes

fileIndex

Column	Syntax	OID
fileIndexmandatory A unique file index. File indices are recalculated every time the router reboots to reflect the current files on the router. As files are added, new indices are allocated to the new files.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.56.1.1.1
fileNamemandatory The name of the file, in the form <name.typ>. The name is up to eight characters long, the type is up to three characters long.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.56.1.1.2
fileDevicemandatory The device on which the file resides.	Enumeration Enumerated Values: 1 flash 2 nvs	.1.3.6.1.4.1.207.8.4.4.4.56.1.1.3
fileCreationTimemandatory The creation date and time for the file, in the format <dd-mmm-yy, hh:mm:ss>.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.56.1.1.4
fileStatusmandatory The status of the file. When read, this object will always return a value of ok(1), since the object will not exist if the value is deleting(2). Write the value deleting(2) to this object to delete the file.	Enumerationr/w Enumerated Values: 1 ok 2 deleting	.1.3.6.1.4.1.207.8.4.4.4.56.1.1.5
fileSizemandatory The size, in bytes, of the file.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.56.1.1.6

The table of ping parameters, dynamic and static.

pingEntry row .1.3.6.1.4.1.207.8.4.4.4.58.1.1

A single entry of ping parameters. This contains the
parameters required to perform a ping from the router.
The ping specified by the dynamic parameters, can be
initiated or stopped at any time by altering the pingStat…

Indexes

pingIndex

Column	Syntax	OID
pingIndexmandatory There are two sets of ping information, dynamic and static. The dynamic information is used only once, for the next ping, then automatically replaced with the static information. The static information is used whenever…	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.1
pingProtocolmandatory The protocol that the ping will use. The protocol must match the destination address. Ping supports both IP, IPX, Appletalk, and OSI addresses. The protocol must be specified before the address is set, because when th…	Enumerationr/w Enumerated Values: 0 undefined 1 apple 2 ip 3 ipx 4 osi	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.2
pingAddressmandatory The address specifies the destination address for ping packets for Appletalk, IP, IPX and OSI networks, respectively. The address format must match the protocol being used. The protocol must be specified before the addr…	OctetStringr/w	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.3
pingNumberOfPacketsmandatory The number of ping packets to transmit.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.4
pingPacketSizemandatory The packet size parameter specifies the length in bytes, of data to include in the data portion of the ping packet. The protocol packet header size and the size of headers for the particular link protocol in use have t…	Integer32r/w Constraints: range: 0-1500	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.5
pingTimeoutmandatory Timeout specifies the amount of time, in seconds, to wait for a response to a ping packet.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.6
pingDelaymandatory The delay parameter specifies the time interval, in seconds, between ping packets.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.7
pingTrapOnCompletionmandatory Specifies whether a trap should be issued on completion of the sequence of pings.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.8
pingTypeOfServicemandatory The Type Of Service (TOS) parameter is only valid for IP addresses, and specifies the TOS field in the IP header of the ping packet, as a decimal in the range 0 to 255.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.9
pingPatternmandatory The pattern parameter specifies the data pattern to use in the data portion of the ping packet.	Unsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.58.1.1.10

The table of DHCP ranges.

dhcpRangeEntry row .1.3.6.1.4.1.207.8.4.4.4.70.1.1

A single entry of the DHCP range table. This contains
information about a single DHCP range configured on this
device.

Indexes

dhcpRangeIndex

Column	Syntax	OID
dhcpRangeIndexmandatory The index of this DHCP range. DHCP ranges are stored in a list which is ordered by range name. The index gives the place in the list. Note that if ranges are added or deleted, the index for a given range will change. Si…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.70.1.1.1
dhcpRangeNamemandatory The name given to identify this DHCP range. This is the ultimate method for uniquely identifying this range. Names are compared without regard to case, for example >range1< will be treated as the same as >RANGE1<.	OctetString Constraints: range: 1-15	.1.3.6.1.4.1.207.8.4.4.4.70.1.1.2
dhcpRangeBaseAddressmandatory The base address of this range. This address defines the lower bound of the range of IP addresses which can be allocated to devices requesting an IP address via DHCP.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.70.1.1.3
dhcpRangeNumberOfAddressesmandatory The number of IP address in this range. This number defines the upper bound of the range of IP addresses which can be allocated to devices requesting an IP address via DHCP.	Integer32 Constraints: range: 1-256	.1.3.6.1.4.1.207.8.4.4.4.70.1.1.4
dhcpRangeGatewaymandatory The IP address of the BOOTP relay agent which will be relaying DHCP requests for this range. If this address is 0.0.0.0, then there will be no BOOTP relay agent and the range will be allocated to devices directly connec…	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.70.1.1.5

The table of defined DHCP range client addresses.

dhcpClientEntry row .1.3.6.1.4.1.207.8.4.4.4.70.3.1

A single entry of the DHCP range client table. This contains
information about a single DHCP range client address.

Indexes

dhcpRangeIndex dhcpClientIpAddress

Column	Syntax	OID
dhcpClientIpAddressmandatory An IP address from the range of available addresses.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.70.3.1.1
dhcpClientIDmandatory The hardware address of the client, if any, that has been assigned the IP address.	OctetString	.1.3.6.1.4.1.207.8.4.4.4.70.3.1.2
dhcpClientStatemandatory The state of the IP address; one of unused, inuse or reclaim.	Enumeration Enumerated Values: 0 unused 1 reclaiming 2 inuse 3 offered	.1.3.6.1.4.1.207.8.4.4.4.70.3.1.3
dhcpClientTypemandatory The type of allocation mechanism applied to the IP address; one of static, auto or dyn.	Enumeration Enumerated Values: 1 auto 2 dyn 3 static	.1.3.6.1.4.1.207.8.4.4.4.70.3.1.4
dhcpClientExpirymandatory The expiry date for dynamically allocated IP address.	OctetString	.1.3.6.1.4.1.207.8.4.4.4.70.3.1.5

Table of port properties.

swiPortEntry row .1.3.6.1.4.1.207.8.4.4.4.87.1.1

An entry in the port information table.

Indexes

swiPortNumber

Column	Syntax	OID
swiPortNumbermandatory This object identifies the port of the switch.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.87.1.1.1
swiPortIngressLimitmandatory The Ingress Bandwidth Limit applied to the port. A value of zero indicates that no limit is set.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.87.1.1.20
swiPortEgressLimitmandatory The Egress Bandwidth Limit applied to the port. A value of zero indicates that no limit is set.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.87.1.1.21

Table of swi56xx port counter properties.

swi56xxPortCounterEntry row .1.3.6.1.4.1.207.8.4.4.4.87.2.1

An entry in the port information table.

Indexes

swi56xxPortNumber

Column	Syntax	OID
swi56xxPortNumbermandatory This object identifies the port of the switch.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.1
swi56xxRxTx64kPktsmandatory The number of 64kB packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.2
swi56xxRxTx65To127kPktsmandatory The number of 65kB To 127kB packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.3
swi56xxRxTx128To255kPktsmandatory The number of 128kB To 255kB packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.4
swi56xxRxTx256To511kPktsmandatory The number of 256kB To 511kB packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.5
swi56xxRxTx512To1023kPktsmandatory The number of 512kB To 1023kB packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.6
swi56xxRxTx1024ToMaxPktSzPktsmandatory The number of 1024kB To MaxPktSz packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.7
swi56xxRxTx519To1522kPktsmandatory The number of 519kB To 1522kB packets received and transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.8
swi56xxPortRxOctetsmandatory The number of octets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.9
swi56xxPortRxPktsmandatory The number of packets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.10
swi56xxPortRxFCSErrorsmandatory The number of frames received containing a Frame Check Sequence error.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.11
swi56xxPortRxMulticastPktsmandatory The number of multicast packets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.12
swi56xxPortRxBroadcastPktsmandatory The number of broadcast packets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.13
swi56xxPortRxPauseMACCtlFrmsmandatory The number of valid PAUSE MAC Control frames received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.14
swi56xxPortRxOversizePktsmandatory The number of oversize packets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.15
swi56xxPortRxFragmentsmandatory The number of fragments received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.16
swi56xxPortRxJabbersmandatory The number of jabber frames received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.17
swi56xxPortRxMACControlFrmsmandatory The number of MAC Control frames (Pause and Unsupported) received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.18
swi56xxPortRxUnsupportOpcodemandatory The number of MAC Control frames with unsupported opcode (i.e. not Pause) received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.19
swi56xxPortRxAlignmentErrorsmandatory The number of frames with alignment errors received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.20
swi56xxPortRxOutOfRngeLenFldmandatory The number of packets with length out of range received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.21
swi56xxPortRxSymErDurCarriermandatory The number of frames with invalid data symbols received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.22
swi56xxPortRxCarrierSenseErrmandatory The number of false carrier conditions between frames received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.23
swi56xxPortRxUndersizePktsmandatory The number of undersized packets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.24
swi56xxPortRxIpInHdrErrorsmandatory swiPortRxIpInHdrErrors	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.25
swi56xxPortTxOctetsmandatory The number of octets transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.26
swi56xxPortTxPktsmandatory The number of packets transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.27
swi56xxPortTxFCSErrorsmandatory The number of frames containing a Frame Check Sequence error transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.28
swi56xxPortTxMulticastPktsmandatory The number of multicast packets transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.29
swi56xxPortTxBroadcastPktsmandatory The number of broadcast packets transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.30
swi56xxPortTxPauseMACCtlFrmsmandatory The number of valid PAUSE MAC Control frames transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.31
swi56xxPortTxOversizePktsmandatory The number of oversize packets transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.32
swi56xxPortTxFragmentsmandatory The number of fragments transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.33
swi56xxPortTxJabbersmandatory The number of jabber frames transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.34
swi56xxPortTxPauseCtrlFrmsmandatory The number of Pause control frames transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.35
swi56xxPortTxFrameWDeferrdTxmandatory The number of frames deferred once before successful transmission.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.36
swi56xxPortTxFrmWExcesDefermandatory The number of frame aborted after too many deferrals.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.37
swi56xxPortTxSingleCollsnFrmmandatory The number of frames which experienced exactly one collision.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.38
swi56xxPortTxMultCollsnFrmmandatory The number of frames which experienced 2 to 15 collisions (including late collisions).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.39
swi56xxPortTxLateCollsnsmandatory The number of frames which experienced late collisions.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.40
swi56xxPortTxExcessivCollsnsmandatory The number of frames aborted before transmission after 16 collisions.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.41
swi56xxPortTxCollisionFramesmandatory The total number of collisions.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.42
swi56xxPortMiscDropEventsmandatory The number of packets discarded at ingress port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.43
swi56xxPortMiscTaggedPktTxmandatory The number of VLAN tagged packets transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.44
swi56xxPortMiscTotalPktTxAbortmandatory The number of Layer 2 and 3 packets aborted during transmission.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.45
swi56xxPortHWMultiTTLexpiredmandatory Number of multicast TTL expired frames.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.46
swi56xxPortHWMultiBridgedFramesmandatory Number of multicast bridged frames	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.47
swi56xxPortHWMultiRxDropsmandatory Number of multicast frames dropped at reception	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.48
swi56xxPortHWMultiTxDropsmandatory NNumber of multicast frames dropped at transmission	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.207.8.4.4.4.87.2.1.49

General configuration and status of all of the virtual balancers 
configured on the router.

lbShowGlobalEntry row .1.3.6.1.4.1.207.8.4.4.4.104.1.1

An entry in the global table.

Indexes

lbGlobalIndex

Column	Syntax	OID
lbGlobalIndexmandatory The index for the global table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.1
lbAffinityTimeOutmandatory The length of time in seconds that a resource can be associated to a source IP address or Cookie after the connection has been closed.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.2
lbOrphanTimeOutmandatory The length of time in seconds that a connection can exist without having any data traversing it, before being declared an orphan and closed by the router.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.3
lbCriticalRstmandatory The ratio of total messages received from a resource that can be TCP RST messages represented as a percentage.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.4
lbTotalResourcesmandatory The total number of resources configured on the router.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.5
lbTotalResPoolsmandatory The total number of resource pools configured on the router.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.6
lbTotalVirtBalsmandatory The total number of virtual balancers configured on the router.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.7
lbCurrentConnectionsmandatory Displays the current total number of connections to all resources in every resource pool on the router.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.1.1.8

A list about the general information about for a given resource.

lbShowResEntry row .1.3.6.1.4.1.207.8.4.4.4.104.2.1

An entry in the resource table.

Indexes

lbResIndex

Column	Syntax	OID
lbResIndexmandatory The index for the resource table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.1
lbResourcemandatory The name of the resource.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.2
lbResIpmandatory The IP address that a virtual balancer uses to accesses the resource.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.3
lbResPortmandatory The port that the service that the resource offer is accessed on.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.4
lbResStatemandatory The current state of the resource, either UP, DOWN, or CLOSING.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.5
lbResWeightmandatory The weight that the virtual balancer will apply to the resource when selecting resources to try a connection to from a resource pool using either the WEIGHTEDLEASTCONNECT or WEIGHTEDLOTTERY selection algorithms.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.6
lbResTotalConnectionsmandatory The total number of successful connections that have been made to this resource while it has been in the UP state.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.7
lbResCurrentConnectionsmandatory The total number of connections currently made to the resource.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.2.1.8

A list about the general information about for a given 
resource pool.

lbShowResPoolEntry row .1.3.6.1.4.1.207.8.4.4.4.104.3.1

An entry in the resource pool table.

Indexes

lbResPoolIndex lbResPoolResourceIndex

Column	Syntax	OID
lbResPoolIndexmandatory The index for the resource pool table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.1
lbResPoolResourceIndexmandatory The index for the resource table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.2
lbResPoolmandatory The name of the resource pool.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.3
lbResPoolSelectionAlgmandatory The selection algorithm that ius employed by this resource pool when a resource has been selected for a connection. The options are ROUNDROBIN, WEIGHTEDLEASTCONNECT, WEIGHTEDLOTTERY and FASTESTRESPONSE.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.4
lbResPoolFailOnLastmandatory Indicates whether or not the resource pool will fail a resource if it is the last resource in the resource pool.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.5
lbResPoolTotalConnectionsmandatory The total number of successful connections that have been made to the resources in the resource pool over the lifetime of the resource pool.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.6
lbResPoolResourcesmandatory The name of the resource that is currently allocated to the resource pool.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.3.1.7

A list about the general information about for a given 
virtual balancer.

lbShowVirtBalEntry row .1.3.6.1.4.1.207.8.4.4.4.104.4.1

An entry in the virtual balancer table.

Indexes

lbVirtBalIndex

Column	Syntax	OID
lbVirtBalIndexmandatory The index for the virtual balancer table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.1
lbVirtBalmandatory The name of the virtual balancer.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.2
lbVirtBalPublicIpmandatory The IP address on which the virtual balancer will receive requests for the service provided by the resource pool associated with it.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.3
lbVirtBalPublicPortmandatory The port on which the virtual balancer will receive requests for the service provided by the resource pool associated with it.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.4
lbVirtBalStatemandatory The current state of the virtual balancer, can either be UP, CLOSING, or DOWN.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.5
lbVirtBalResPoolmandatory The name of the resource pool that is associated with the virtual balancer.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.6
lbVirtBalTypemandatory The type of load balancer that this virtual balancer currently is, can be either TCP, HTTP, or ROUTE.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.7
lbVirtBalTotalConnectionsmandatory The total number of stateful connections currently running through this virtual balancer.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.8
lbVirtBalAffinitymandatory Indicates whether or not entries will be made in a virtual balancers' affinity table for each stateful connection to a resource in its' resource pool (TCP and ROUTE type) or for cookies received from clients (HTTP type…	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.9
lbVirtBalHttpErrorCodemandatory A list of the HTTP server error status code added.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.4.1.10

A list of affinity tables for all configured virtual balancers on the router.

lbShowAffEntry row .1.3.6.1.4.1.207.8.4.4.4.104.5.1

An entry in the affinity table.

Indexes

lbAffIndex

Column	Syntax	OID
lbAffIndexmandatory The index for the affinity table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.5.1.1
lbAffVirtBalmandatory The name of the virtual balancer whose affinity table is being displayed.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.5.1.2
lbAffClientIpmandatory The IP address that has affinity to the given resource.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.104.5.1.3
lbAffCookiemandatory The cookie that has affinity to the given resource.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.5.1.4
lbAffResourcemandatory The name of the resource that the Client IP/Cookie has an affinity for.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.5.1.5
lbAffExpirymandatory The amount of seconds left before this entry expires, and is removed from the affinity table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.5.1.6

A list about all of the TCP connections currently open to a given virtual balancer.

lbShowConEntry row .1.3.6.1.4.1.207.8.4.4.4.104.6.1

An entry in the connections table.

Indexes

lbConIndex

Column	Syntax	OID
lbConIndexmandatory The index for the connections table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.6.1.1
lbConVirtBalmandatory The name of the virtual balancer the listed connections are to.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.6.1.2
lbConClientIpmandatory The IP address of that originated the connection.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.207.8.4.4.4.104.6.1.3
lbConPortmandatory The port on the originating system that represents the other end of the connection.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.207.8.4.4.4.104.6.1.4
lbConResourcemandatory The name of the resource that the connection has been made to.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.207.8.4.4.4.104.6.1.5

The ATR enterprise DS3 trap table.

ds3TrapEntry row .1.3.6.1.4.1.207.8.4.4.4.109.1.1

An entry in the ATR enterprise DS3 trap table.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ds3TcaTrapEnablemandatory Indicates whether the threshold crossing alert traps should be generated for this interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.207.8.4.4.4.109.1.1.1
ds3TrapErrormandatory This variable shows which kind of parameter or primitive caused the trap. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will h…	Enumeration Enumerated Values: 1 ds3NoError 2 ds3PES 3 ds3PSES 4 ds3SEFs 5 ds3UAS 6 ds3LCVs 7 ds3PCVs 8 ds3LESs 9 ds3CCVs 10 ds3CESs 11 ds3CSESs	.1.3.6.1.4.1.207.8.4.4.4.109.1.1.2
ds3TrapLocmandatory This variable shows whether the trap was caused by a problem at the local or remote end. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The …	Enumeration Enumerated Values: 1 ds3NoLoc 2 ds3Near 3 ds3Far	.1.3.6.1.4.1.207.8.4.4.4.109.1.1.3
ds3TrapIntervalmandatory This variable shows whether the counter which has crossed the threshold is a twenty four hour or fifteen minute counter. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read …	Enumeration Enumerated Values: 1 ds3NoInt 2 ds3Fifteen 3 ds3Twentyfour	.1.3.6.1.4.1.207.8.4.4.4.109.1.1.4