ALCATEL-IND1-PORT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
15
Rows
15
Columns
214

esmConfTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1 · 1 row entry · 42 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmConfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmConfTable' 
A list of ESM Physical Port instances.
esmConfEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1
A ESM Physical Port entry.
Indexes
Column Syntax OID
esmPortSlot
The physical Slot number for this Ethernet Port.
Slot number has been added to be used by the private Trap.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.1
esmPortIF
The on-board interface number for this Ethernet Port.
Port Number has been added to be used by the private Trap.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.2
esmPortAutoSpeed
The automatically detected port line speed
of this ESM port.
Enumeration
Enumerated Values:
1speed100
2speed10
3speedAuto
4unknown
5speed1000
6speed10000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.3
esmPortAutoDuplexMode
The automatically detected port duplex mode
of this ESM port.

Note: GigaEthernet supports only Full duplex mode.
Default value for 10/100 = Half duplex mode.
Enumeration
Enumerated Values:
1fullDuplex
2halfDuplex
3autoDuplex
4unknown
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.4
esmPortCfgSpeed
The configured port line speed of this ESM port.
Enumerationr/w
Enumerated Values:
1speed100
2speed10
3speedAuto
5speed1000
6speed10000
8speedMax100
9speedMax1000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.5
esmPortCfgDuplexMode
The configured port duplex mode of this ESM port.
Note: GigaEthernet support only full-duplex.
Enumerationr/w
Enumerated Values:
1fullDuplex
2halfDuplex
3autoDuplex
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.6
esmPortCfgIFG
Contains the setting of Inter-Frame Gap (IFG), in bytes
for receive and transmit.
The range is from 9 to 12 bytes.

Note: The default value changed according to the Port type
Default Bandwidth val…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.7
esmPortPauseSlotTime
Indicates the number of microseconds the other
end-station waits after the reception
of a pause frame.

Note: Pause Flow control is not available for 10Mbps.
For 100Mbps, the possible value range i…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.8
esmPortMaxFloodRate
Broadcast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also.
The default value for flood rate is:
1. 4 mbps if the port speed is 10 mbps,
2. 49 mbps if the port speed is 100 mbps
…
Enumerationr/w
Enumerated Values:
1mbps
2percentage
3pps
4default
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.9
esmPortFloodMcastEnable
Enable/disable the maximum flood rate
for multicast.
Enumerationr/w
Enumerated Values:
0enableFlood
1enableMulticastFlood
2disableMulticastFlood
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.10
esmPortCfgMaxFrameSize
Configure the value of the maximum frame
size allow.
For 10/100:
It is a range between 1518(untagged) and 1553 bytes.
For GigaEthernet:
It is a range between 1518 and 10240 bytes.(OS7700,OS7800,OS8800)
It is a range…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.11
esmPortCfgLongEnable
Allow the user to change the maximun Frame size.
Note: It is not configurable for 10/100 Ethernet port.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.12
esmPortCfgRuntEnable
Allow the user to change the minimum Frame size.
Enumerationr/w
Enumerated Values:
2disable
3enable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.13
esmPortCfgRuntSize
Configure the value of the minimum frame
size allow per ports.
The range is 0 to 64.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.14
esmPortCfgAutoNegotiation
Allow the user to enable or disable the port auto negotiation.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.15
esmPortCfgCrossover
Allow the user to configure port crossover.
Enumerationr/w
Enumerated Values:
1mdi
2mdix
3auto
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.16
esmPortCfgFlow
Use the dot3PauseAdminMode from the standard MIB to configure the flow control.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.17
esmPortCfgHybridActiveType
This object is only applicable to hybrid ports .
It indicates configured active media type.(the operational media
type may be different if esmPortCfgHybridMode is configured to be
preferredFiber or preferredCopper)
For …
Enumeration
Enumerated Values:
0notapplicable
1fiber
2copper
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.18
esmPortCfgHybridMode
This object is only applicable to hybrid ports.
This allows the user the user to configure the media type
with which the port should come up.
The user can configure the port to come as copper only
or fiber only or ei…
Enumerationr/w
Enumerated Values:
0notapplicable
1preferredCopper
2forcedCopper
3preferredFiber
4forcedFiber
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.19
esmPortOperationalHybridType
This object is only applicable to hybrid ports .
It indicates the actual media type that has link up and is or will be
passing traffic. If link is not present the object will return none(0) value.
Enumeration
Enumerated Values:
0none
1fiber
2copper
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.20
esmPortCfgMMULowWaterMarkCellSetLimit
Per-port-per-CoS Head of Line blocking cell limits. Range is 0 - 16383
Firebolt register Offset: 0x006pp30 - 0x37
Bits: 13:0 CellSetLimit , Default: 0x0100
This setting allocates the guaranteed cells for one port's CoSx…
Integer32r/w
Constraints:
range: 0-16383
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.21
esmPortCfgMMUDynamicCellSetLimit
Per-egress port cell-based dynamic (shared buffer pool) memory
usage drop and resume thresholds. This sets the limit for which
the eight CoS-Qs within a port may share once the LWMCOSCELL
limit is exceeded. Range is 0 -…
Integer32r/w
Constraints:
range: 0-16383
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.22
esmPortViolationBitMap
A bit map that identifies the set of Application that have blocked
a port as a result of a particular violation
Bits
Enumerated Values:
0bEniSecurityBlockPortENI
1bEniSecurityBlockPortSTP
2bEniSecurityBlockPortSL
3bEniSecurityBlockPortQoS
4bEniSecurityBlockPortUDLD
5bEniSecurityBlockPortETHBLK
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.23
esmPortViolationClearAll
Clear all port vioaltion
Integer32r/w
Constraints:
range: 0-0
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.24
esmPortFloodBcastEnable
Enable/disable the maximum flood rate
for Broadcast.
Enumerationr/w
Enumerated Values:
1enableBcastFlood
2disableBcastFlood
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.25
esmPortFloodUnknownUcastEnable
Enable/disable the maximum flood rate
for unknown unicast.
Enumerationr/w
Enumerated Values:
1enableUnknownUcastFlood
2disableUnknownUcastFlood
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.26
esmPortMaxUnknownUcastFloodRate
Unknown-Unicast flood threshold type. To set the type, set esmPortMaxUnknownUcastFloodRateLimit also.
The default value for flood rate is:
1. 4 mbps if the port speed is 10 mbps,
2. 49 mbps if the port speed…
Enumerationr/w
Enumerated Values:
1mbps
2percentage
3pps
4default
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.27
esmPortMaxMcastFloodRate
Multicast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also.
The default value for flood rate is:
1. 4 mbps if the port speed is 10 mbps,
2. 49 mbps if the port speed is 100 mbps
3. 496 mbps if…
Enumerationr/w
Enumerated Values:
1mbps
2percentage
3pps
4default
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.28
esmPortMaxFloodRateLimit
The value of the maximum broadcast flood limit.
The actual range of the flood limit depends on the port speed.
example:
Percentage: 1 - 100
Mbps: 1 - 1000 (1G speed)
PPS: 244 - 244262 (1G speed)
To set the …
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.29
esmPortMaxUnknownUcastFloodRateLimit
The value of the maximum unknown-unicast flood limit
The actual range of the flood limit depends on the port speed.
example:
Percentage: 1 - 100
Mbps: 1 - 1000 (1G speed)
PPS: 244 - 244262 (1G speed)
To set…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.30
esmPortMaxMcastFloodRateLimit
The value of the maximum multicast flood limit
The actual range of the flood limit depends on the port speed.
example:
Percentage: 1 - 100
Mbps: 1 - 1000 (1G speed)
PPS: 244 - 244262 (1G speed)
To set the l…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.31
esmPortCfgSFPType
This object is only applicable to fiber ports.
The string indicates the type of SFP/GBIC of active media.
OctetString
Constraints:
range: 0-64
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.32
esmPortWaitToRestoreTimer
Indicates the number of seconds after which the link up
event is notified to other applications.
The timer is started whenever a Link Up is detected on a port being monitored.
Integer32r/w
Constraints:
range: 0-300
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.33
esmPortMinFloodRateLimit
The value of the minimum broadcast flood limit
this value should be same type as that of the
maximum value configured for broadcast traffic.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.34
esmPortMinMcastFloodRateLimit
The value of the minimum multicast flood limit
this value should be same type as that of the
maximum value configured for multicast traffic.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.35
esmPortFloodThresholdAction
The action to be taken when the broadcast
traffic exceeding the maximum configured value.
Enumerationr/w
Enumerated Values:
0default
1trap
2shutdown
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.36
esmPortMcastThresholdAction
The action to be taken when the multicast
traffic exceeding the maximum configured value.
Enumerationr/w
Enumerated Values:
0default
1trap
2shutdown
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.37
esmPortFlood
The state of the port, is it having normal or stormed broad
cast traffic.
Enumeration
Enumerated Values:
0normal
1storm
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.38
esmPortMCastStorm
The state of the port, is it having normal or stormed
mulit cast traffic.
Enumeration
Enumerated Values:
0normal
1storm
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.39
esmPortCfgEeeStatus
Allow the user to enable or disable the port EEE mode.
Enumerationr/w
Enumerated Values:
1enable
2disable
3na
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.40
esmPortCfgEeeAutoNegState
Current autoneg state of EEE enabled port.
Enumeration
Enumerated Values:
0none
1speed10
2speed100
3unknown
4speed1000
5na
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.41
esmPortCfgEeeCapability
Current cpapbility of EEE enabled port.
Enumeration
Enumerated Values:
0none
1speed10
2speed100
3speed100Speed1000
4speed1000
5na
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.42

alcetherStatsTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2 · 1 row entry · 45 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alcetherStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alcetherStatsTable' 
A list of Ethernet statistics entries.
alcetherStatsEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1
A collection of statistics kept for a particular
Ethernet interface. As an example, an instance of the
etherStatsPkts object might be named alcetherStatsPkts.1
Indexes
Column Syntax OID
alcetherClearStats
Used to Clear all Statistics counters.
By default, this object contains zero value.
Enumerationr/w
Enumerated Values:
0default
1reset
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.1
alcetherLastClearStats
The value of SysUpTime at the time of all
the statistics counters are cleared.
By default, this object contains a zero value.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.2
alcetherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and 1518
octets, inclusive, but but had either a bad
Frame Check Sequence (FCS) with an integral
nu…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.3
alcetherStatsRxUndersizePkts
The total number of packets received that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.4
alcetherStatsTxUndersizePkts
The total number of packets transmitted that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.5
alcetherStatsTxOversizePkts
The total number of packets transmitted that were
longer than 1518 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.6
alcetherStatsRxJabbers
The total number of packets received that were
longer than 1518 octets (excluding framing bits,
but including FCS octets), and had either a bad
Frame Check Sequence (FCS) with an integral number
of octets (FCS Error) or…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.7
alcetherStatsRxCollisions
The best estimate of the total number of collisions
on this Ethernet segment (in reception).
Only for Ethernet Interfaces.

The value returned will depend on the location of
the RMON probe. Section 8.2.1.…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.8
alcetherStatsTxCollisions
The best estimate of the total number of collisions
on this Ethernet segment (in transmition).
Only for Ethernet Interfaces.

The value returned will depend on the location of
the RMON probe. Section 8.2.…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.9
alcetherStatsPkts64Octets
The total number of packets (including bad
packets) received that were 64 octets in length
(excluding framing bits but including FCS octets).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.10
alcetherStatsPkts65to127Octets
The total number of packets (including bad
packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS octets).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.11
alcetherStatsPkts128to255Octets
The total number of packets (including bad
packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS octets).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.12
alcetherStatsPkts256to511Octets
The total number of packets (including bad
packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS octets).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.13
alcetherStatsPkts512to1023Octets
The total number of packets (including bad
packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS octets).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.14
alcetherStatsPkts1024to1518Octets
The total number of packets (including bad
packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS octets).
For both Ethernet and GigaEthernet.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.15
gigaEtherStatsPkts1519to4095Octets
The total number of packets (including bad
packets) received that were between
1519 and 4095 octets in length inclusive
(excluding framing bits but including FCS octets).
Only for GigaEthernet interfaces
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.16
gigaEtherStatsPkts4096to9215Octets
The total number of packets (including bad
packets) received that were between
4096 and 9215 octets in length inclusive
(excluding framing bits but including FCS octets).
Only for GigaEthernet interfaces
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.17
alcetherStatsPkts1519to2047Octets
The total number of frames(including error packets) received
that were between 1519 and 2047 bytes in length inclusive
(excluding framing bits but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.18
alcetherStatsPkts2048to4095Octets
The total number of frames(including error packets) received
that were between 2048 and 4095 bytes in length inclusive
(excluding framing bits but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.19
alcetherStatsPkts4096Octets
The total number of frames(including error packets) received
that were greater than or equal to 4096 bytes in length inclusive
(excluding framing bits but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.20
alcetherStatsRxGiantPkts
The total number of frames that are greater than the specified
Max length value, with a valid CRC, dropped because too long.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.21
alcetherStatsRxDribbleNibblePkts
The total number of frames for which a dribble nibble has been
received and CRC is correct.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.22
alcetherStatsRxLongEventPkts
The total number of frames for which the Carrier sense exceeds
50000 bit times for 10 Mbits/sec or 80000 bit times for
100 Mbits/sec.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.23
alcetherStatsRxVlanTagPkts
The total number of frames for which Type/Length field
contains the VLAN protocol identifier (0x8100).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.24
alcetherStatsRxControlPkts
The total number of frames that were recognized as control frames.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.25
alcetherStatsRxLenChkErrPkts
The total number of frames for which the frame length field value
in the Type/Length field does not match the actual data bytes
length and is NOT a type field.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.26
alcetherStatsRxCodeErrPkts
The total number of frames for which one or more nibbles were
signaled as errors during reception of the frame.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.27
alcetherStatsRxDvEventPkts
The total number of frames for which a RX_DV event (packet not
too long enough to be valid packet) has been seen before the
correct frame.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.28
alcetherStatsRxPrevPktDropped
The total number of frames for which a packet has been dropped
(because of too small IFG) before the correct frame.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.29
alcetherStatsTx64Octets
The total number of transmitted frames of 64 bytes.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.30
alcetherStatsTx65to127Octets
The total number of transmitted frames that were between
65 and 127 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.31
alcetherStatsTx128to255Octets
The total number of transmitted frames that were between
128 and 255 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.32
alcetherStatsTx256to511Octets
The total number of transmitted frames that were between
256 and 511 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.33
alcetherStatsTx512to1023Octets
The total number of transmitted frames that were between
512 and 1023 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.34
alcetherStatsTx1024to1518Octets
The total number of transmitted frames that were between
1024 and 1518 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.35
alcetherStatsTx1519to2047Octets
The total number of transmitted frames that were between
1519 and 2047 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.36
alcetherStatsTx2048to4095Octets
The total number of transmitted frames that were between
2048 and 4095 bytes in length inclusive (excluding framing bits
but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.37
alcetherStatsTx4096Octets
The total number of transmitted frames that were greater than
or equal to 4096 bytes in length and less than Max frame length
(excluding framing bits but including FCS bytes).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.38
alcetherStatsTxRetryCount
The total number of collisions that the frames faced during
transmission attempts.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.39
alcetherStatsTxVlanTagPkts
The total number of transmitted frames for which Type/Length field contains the
VLAN protocol identifier (0x8100).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.40
alcetherStatsTxControlPkts
The total number of transmitted frames that were recognised as control frames.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.41
alcetherStatsTxLatePkts
The total number of late collisions that occured beyond the collision window.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.42
alcetherStatsTxTotalBytesOnWire
The total number of bytes transmitted on wire, including all bytes from collided
attempts.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.43
alcetherStatsTxLenChkErrPkts
The total number of transmitted frames for which the frame length field value
in the Type/Length field does not match the actual data bytes length and
is NOT a Type field.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.44
alcetherStatsTxExcDeferPkts
The total number of frames that were deferred in excess of 6071 nibble-times
in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This
stat is only in case of Half duplex and excessive defer bit reset…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.45

esmHybridConfTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3 · 1 row entry · 7 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmHybridConfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmHybridConfTable' 
A list of inactive hybrid port instances.
esmHybridConfEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1
A ESM Physical Port entry.
Indexes
Column Syntax OID
esmHybridPortCfgSpeed
The configured port line speed of this ESM port.
Enumerationr/w
Enumerated Values:
1speed100
2speed10
3speedAuto
5speed1000
6speed10000
8speedMax100
9speedMax1000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.1
esmHybridPortCfgDuplexMode
The configured port duplex mode of this ESM port.
Note: GigaEthernet support only full-duplex.
Enumerationr/w
Enumerated Values:
1fullDuplex
2halfDuplex
3autoDuplex
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.2
esmHybridPortCfgAutoNegotiation
Allow the user to enable or disable the port auto negotiation.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.3
esmHybridPortCfgCrossover
Allow the user to configure port crossover.
Enumerationr/w
Enumerated Values:
1mdi
2mdix
3auto
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.4
esmHybridPortCfgFlow
This object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode
object in dot3PauseTable. It is used to configure pause for fiber media.
Enumerationr/w
Enumerated Values:
1disable
2enabledXmit
3enabledRcv
4enabledXmitAndRcv
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.5
esmHybridPortCfgInactiveType
This object is only applicable to hybrid ports .
It indicates the configured inactive media type.
Enumeration
Enumerated Values:
1fiber
2copper
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.6
esmHybridPortCfgSFPType
This object is only applicable to fiber ports.
The string indicates the type of SFP/GBIC of active media.
OctetString
Constraints:
range: 0-64
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.7

alcether10GigTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.4 · 1 row entry · 1 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alcether10GigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alcether10GigTable' 
A list of 10 Gig specifics entries.
alcether10GigEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.4.1
This table will be populated with the 10 gig only entries.
The management interface can use it to specify if A or B is the primary.
Indexes
Column Syntax OID
alcether10GigPrimary
Setting the object to 1 will make phy A as primary, 2- phy B as pirmary.
Value 3 should not be set.
Enumerationr/w
Enumerated Values:
1phyAprimary
2phyBprimary
3notApplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.4.1.1

ddmInfoTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5 · 1 row entry · 25 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk ddmInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::ddmInfoTable' 
The ddmInfoTable has an entry for each SFP/XFP in the
system that supports Digital Diagnostic Monitoring (DDM). The table is
indexed by ifIndex. Each row in this table is dynamically added
and removed internally by the system based on the presence or absence
of DDM capable SFP/XFP components.
ddmInfoEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1
Each row represents a particular SFP/XFP that supports Digital
Diagnostic Monitoring.
Entries are created and deleted internally by the system.
Indexes
Column Syntax OID
ddmTemperature
The value of ddmTemperature indicates the current temperature
of the SFP/XFP in 1000s of degrees Celsius.
A value of -200000 indicates this object is not applicable.
thousandth of a degree celciusInteger32
Constraints:
range: -150000-150000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.1
ddmTempLowWarning
The value of ddmTempLowWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a degree celciusInteger32
Constraints:
range: -150000-150000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.2
ddmTempLowAlarm
The value of ddmTempLowAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a degree celciusInteger32
Constraints:
range: -150000-150000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.3
ddmTempHiWarning
The value of ddmTempHiWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a degree celciusInteger32
Constraints:
range: -200000--200000
range: -150000-150000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.4
ddmTempHiAlarm
The value of ddmTempHiAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a degree celciusInteger32
Constraints:
range: -150000-150000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.5
ddmSupplyVoltage
The value of ddmSupplyVoltage indicates the current supply
voltage of the SFP/XFP in 1000s of Volts (V).
A value of -200000 indicates this object is not applicable.
thousandth of a voltInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.6
ddmSupplyVoltageLowWarning
The value of ddmSupplyVoltageLowWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a voltInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.7
ddmSupplyVoltageLowAlarm
The value of ddmSupplyVoltageLowAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a voltInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.8
ddmSupplyVoltageHiWarning
The value of ddmSupplyVoltageHiWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a voltInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.9
ddmSupplyVoltageHiAlarm
The value of ddmSupplyVoltageHiAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a voltInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.10
ddmTxBiasCurrent
The value of ddmTxBiasCurrent indicates the current Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
A value of -200000 indicates this object is not applicable.
thousandth of a milli-AmpereInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.11
ddmTxBiasCurrentLowWarning
The value of ddmTxBiasCurrentLowWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a milli-AmpereInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.12
ddmTxBiasCurrentLowAlarm
The value of ddmTxBiasCurrentLowAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a milli-AmpereInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.13
ddmTxBiasCurrentHiWarning
The value of ddmTxBiasCurrentHiWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a milli-AmpereInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.14
ddmTxBiasCurrentHiAlarm
The value of ddmTxBiasCurrentHiAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a milli-AmpereInteger32
Constraints:
range: 0-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.15
ddmTxOutputPower
The value of ddmTxOutputPower indicates the current Output
Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.16
ddmTxOutputPowerLowWarning
The value of ddmTxOutputPowerLowWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -200000--200000
range: -40000-10000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.17
ddmTxOutputPowerLowAlarm
The value of ddmTxOutputPowerLowAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.18
ddmTxOutputPowerHiWarning
The value of ddmTxOutputPowerHiWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.19
ddmTxOutputPowerHiAlarm
The value of ddmTxOutputPowerHiAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.20
ddmRxOpticalPower
The value of ddmRxOpticalPower indicates the current Received
Optical Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -200000--200000
range: -40000-10000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.21
ddmRxOpticalPowerLowWarning
The value of ddmRxOpticalPowerLowWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.22
ddmRxOpticalPowerLowAlarm
The value of ddmRxOpticalPowerLowAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.23
ddmRxOpticalPowerHiWarning
The value of ddmRxOpticalPowerHiWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.24
ddmRxOpticalPowerHiAlarm
The value of ddmRxOpticalPowerHiAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable.
thousandth of a dBmInteger32
Constraints:
range: -40000-10000
range: -200000--200000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.25

esmPortModeTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6 · 1 row entry · 3 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmPortModeTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmPortModeTable' 
A list of ESM Physical Port Mode instances.
esmPortModeEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1
A ESM Physical Port Mode entry.
Indexes
Column Syntax OID
esmPortModeIndex
Valid ni/port values
Integer32
Constraints:
range: 1001-8128
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1.1
esmPortRunningMode
Currently configured Etna port 25,26 as 10G uplink user port or stacking port.
Default is uplink 10G port. User can not set the current mode.
Enumeration
Enumerated Values:
1uplink
2stackable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1.2
esmPortSavedMode
Next configured Etna port 25,26 as 10G uplink user port or stacking port.
At boot up, it has the same value as current esmPortRunningMode. It takes some time to
write to the EEPROM. Have at least more than 7 sec between…
Enumerationr/w
Enumerated Values:
1uplink
2stackable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1.3

esmTdrPortTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7 · 1 row entry · 32 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmTdrPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmTdrPortTable' 
The table lists the results of cable diagnostics.
esmTdrPortEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1
An entry corresponding to each port.
Indexes
Column Syntax OID
esmTdrPortCableState
State of a cable as returned by the TDR test.
Enumeration
Enumerated Values:
0ok
1open
2short
3openShort
4crossTalk
5unknown
6impedanceMismatch
7shortWithPair1
8shortWithPair2
9shortWithPair3
10shortWithPair4
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.1
esmTdrPortValidPairs
The number of pairs in the cable for which the results of this test are valid.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.2
esmTdrPortPair1State
The state for pair-1 of the cable as returned by the TDR test.
Enumeration
Enumerated Values:
0ok
1open
2short
3openShort
4crossTalk
5unknown
6impedanceMismatch
7shortWithPair1
8shortWithPair2
9shortWithPair3
10shortWithPair4
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.3
esmTdrPortPair1Length
The length for pair-1 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.4
esmTdrPortPair2State
The state for pair-2 of the cable as returned by the TDR test.
Enumeration
Enumerated Values:
0ok
1open
2short
3openShort
4crossTalk
5unknown
6impedanceMismatch
7shortWithPair1
8shortWithPair2
9shortWithPair3
10shortWithPair4
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.5
esmTdrPortPair2Length
The length for pair-2 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.6
esmTdrPortPair3State
The state for pair-3 of the cable as returned by the TDR test.
Enumeration
Enumerated Values:
0ok
1open
2short
3openShort
4crossTalk
5unknown
6impedanceMismatch
7shortWithPair1
8shortWithPair2
9shortWithPair3
10shortWithPair4
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.7
esmTdrPortPair3Length
The length for pair-3 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.8
esmTdrPortPair4State
The state for pair-4 of the cable as returned by the TDR test.
Enumeration
Enumerated Values:
0ok
1open
2short
3openShort
4crossTalk
5unknown
6impedanceMismatch
7shortWithPair1
8shortWithPair2
9shortWithPair3
10shortWithPair4
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.9
esmTdrPortPair4Length
The length for pair-4 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.10
esmTdrPortFuzzLength
The error in the estimated length of the cable (as returned by TDR test).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.11
esmTdrPortTest
Object used to start a TDR test or EXTENDED test on the port. When configured as on, it initiates a TDR test on the port. When configured as extendedOn, it initiates a EXTENDED test on the port. A read operation on this…
Enumerationr/w
Enumerated Values:
0off
1on
2extendedOn
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.12
esmTdrClearStats
Used to Clear TDR stats or EXTENDED stats.
By default, this object contains zero value.
Enumerationr/w
Enumerated Values:
0default
1reset
2extendedReset
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.13
esmTdrResult
Used to give the status of API,whether API able to execute TDR test successfully or failed to executethe TDR test.
Enumeration
Enumerated Values:
0success
1fail
2unknown
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.14
esmTdrPortExtSwapTypeChannel1
Determines the channel associated with the MDI pair(cross or not for each two MDI pairs)
Enumeration
Enumerated Values:
0straightcable
1crossovercable
2swapnotapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.15
esmTdrPortExtSwapTypeChannel2
Determines the channel associated with the MDI pair(cross or not for each two MDI pairs)
Enumeration
Enumerated Values:
0straightcable
1crossovercable
2swapnotapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.16
esmTdrPortExtPolaritySwapPair1
Detects if the pairs connected with reverse polarity(reverse on one side between two conductors in one pair
Enumeration
Enumerated Values:
0positivepolarity
1negativepolarity
2polaritynotapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.17
esmTdrPortExtPolaritySwapPair2
Detects if the pairs connected with reverse polarity(reverse on one side between two conductors in one pair
Enumeration
Enumerated Values:
0positivepolarity
1negativepolarity
2polaritynotapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.18
esmTdrPortExtPolaritySwapPair3
Detects if the pairs connected with reverse polarity(reverse on one side between two conductors in one pair
Enumeration
Enumerated Values:
0positivepolarity
1negativepolarity
2polaritynotapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.19
esmTdrPortExtPolaritySwapPair4
Detects if the pairs connected with reverse polarity(reverse on one side between two conductors in one pair
Enumeration
Enumerated Values:
0positivepolarity
1negativepolarity
2polaritynotapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.20
esmTdrPortExtSkewPair1
The Skew among the four pairs of cable(delay between pairs, in n-Seconds)
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.21
esmTdrPortExtSkewPair2
The Skew among the four pairs of cable(delay between pairs, in n-Seconds)
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.22
esmTdrPortExtSkewPair3
The Skew among the four pairs of cable(delay between pairs, in n-Seconds)
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.23
esmTdrPortExtSkewPair4
The Skew among the four pairs of cable(delay between pairs, in n-Seconds)
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.24
esmTdrPortExtAccurateCableLenPair1
The Length of the cable in meters
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.25
esmTdrPortExtAccurateCableLenPair2
The Length of the cable in meters
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.26
esmTdrPortExtAccurateCableLenPair3
The Length of the cable in meters
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.27
esmTdrPortExtAccurateCableLenPair4
The Length of the cable in meters
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.28
esmTdrPortExtDownshiftStatus
list downshift status of the port
Enumeration
Enumerated Values:
0nodownshift
1downshiftoccurs
2notapplicable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.29
esmTdrExtResult
Used to give the status of API,whether API able to execute TDR Extended test successfully or failed to execute the TDR Extended test.
Enumeration
Enumerated Values:
0success
1fail
2unknown
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.30
esmTdrCableLen
The Approximate Length of a normal cable(Non-Faulty)
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.31
esmTdrPhyType
Lists the Marvell types
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.7.1.32

alaLinkMonConfigTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.8 · 1 row entry · 4 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alaLinkMonConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alaLinkMonConfigTable' 
A list of Link Monitoring Configuration Parameters
alaLinkMonConfigEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.8.1
A collection of Link Monitoring configurations kept for a particular
Ethernet interface.
Indexes
Column Syntax OID
alaLinkMonStatus
Allows the user to enable or disable Link Monitoring on the port.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.8.1.1
alaLinkMonTimeWindow
Indicates the number of seconds the Link will be monitored for a port.
Integer32r/w
Constraints:
range: 0-3600
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.8.1.2
alaLinkMonLinkFlapThreshold
Indicaes the number of link flaps allowed for the specified port
during the time window before the port is shutdown.
Integer32r/w
Constraints:
range: 2-10
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.8.1.3
alaLinkMonLinkErrorThreshold
Indicates the number of link errors allowed on Rx for the specified port
during the time window before the port is shutdown. The errors are the MAC errors
that include CRC, lost frames, error frames, alignment frames.
Integer32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.8.1.4

alaLinkMonStatsTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9 · 1 row entry · 10 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alaLinkMonStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alaLinkMonStatsTable' 
A list of Link Monitoring Statistics
alaLinkMonStatsEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1
A collection of Link Monitoring statistics for a particular
Ethernet interface.
Indexes
Column Syntax OID
alaLinkMonStatsClearStats
Used to Clear all Statistics counters.
The value reset (1) indicates that Link Monitoring shuold all statistic
counters related to the particular port.
By default, this object contains zero value.
Enumerationr/w
Enumerated Values:
0default
1reset
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.1
alaLinkMonStatsPortState
Indicates the status of the port.
up(1) means the port is physically up, down(2) means the port is physically down,
shutdown(3) means the interface is shutdown because of excessive link flaps or link errors.
Enumeration
Enumerated Values:
1up
2down
3shutdown
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.2
alaLinkMonStatsCurrentLinkFlaps
Indicates the number of Link flaps in the current time window.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.3
alaLinkMonStatsCurrentErrorFrames
Indicates the number of error frames in the current time window.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.4
alaLinkMonStatsCurrentCRCErrors
Indicates the number of CRC errors in the current time window.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.5
alaLinkMonStatsCurrentLostFrames
Indicates the number of Rx Lost frames in the current time window.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.6
alaLinkMonStatsCurrentAlignErrors
Indicates the number of Rx alignment frames in the current time window.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.7
alaLinkMonStatsCurrentLinkErrors
Indicates the sum of all the MAC Errors within the current time window.
i.e., the sum of alaLinkMonStatsCurrentErrorFrames, alaLinkMonStatsCurrentCRCErrors,
alaLinkMonCurrentLosFrames, alaLinkMonStatsCurrentAlignErrors.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.8
alaLinkMonStatsTotalLinkFlaps
Indicates the total number of link flaps across all the time windows.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.9
alaLinkMonStatsTotalLinkErrors
Indicates the total number of link errors across all the time windows.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.9.1.10

alaLFPGroupTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10 · 1 row entry · 5 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alaLFPGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alaLFPGroupTable' 
A list of Link Fault Propagation Grooups and their status
alaLFPGroupEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10.1
The list of Link Fault Propagation group id and status for each group
Indexes
Column Syntax OID
alaLFPGroupId
Indicates the unique group id for Link Fault Propagation (LFP).
Integer32
Constraints:
range: 1-8
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10.1.1
alaLFPGroupAdminStatus
Indicates the admin status of the group. disable(0) means link fault propagation,
is disbaled. enable(1) means link fault propagation is enabled
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10.1.2
alaLFPGroupOperStatus
Indicates the operational status of the group. down(0) means all the source ports are down,
up(1) means atleast one source port in the group is up.
Enumeration
Enumerated Values:
0down
1up
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10.1.3
alaLFPGroupWaitToShutdown
0 - Disable wait to shutdown timer
Range 5 - 300, in multiples of 5. After expiry of this timer all destination ports will be shutdown
Integer32r/w
Constraints:
range: 0-300
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10.1.4
alaLFPGroupRowStatus
Row Status for initiating a MIB retrieval request.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.10.1.5

alaLFPConfigTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.11 · 1 row entry · 3 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alaLFPConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alaLFPConfigTable' 
A list of Link Fault Propagation port and port type of each LFP group
alaLFPConfigEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.11.1
A list of Link Fault Propagation port and port type of each LFP group
Indexes
Column Syntax OID
alaLFPConfigPort
Indicates ifindex of source/destination port for a LFP Group.
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.11.1.1
alaLFPConfigPortType
Indicates the type of port, (1) means the port is destination port and
(2) means the port is a source port for a LFP Group.
Enumerationr/w
Enumerated Values:
1destination
2source
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.11.1.2
alaLFPConfigRowStatus
Row Status for initiating a MIB retrieval request.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.11.1.3

esmSlotInfoTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.12 · 1 row entry · 2 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmSlotInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmSlotInfoTable' 
ESM Slot information table.
esmSlotInfoEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.12.1
A ESM Physical slot entry.
Indexes
Column Syntax OID
esmSlotNumber
The slot number on stack.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.12.1.1
esmNumberOfUserPorts
The number of user ports on specified slot number.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.12.1.2

esmPtpStatsTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13 · 1 row entry · 8 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmPtpStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmPtpStatsTable' 
The table lists the Statistics params of PTP.
esmPtpStatsEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1
An entry corresponding to each port.
Indexes
Column Syntax OID
esmPtpStatsIngPtpv2
The number of PTP V2 packets ingress in to the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.1
esmPtpStatsIngPtpv1
The number of PTP V1 packets ingress in to the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.2
esmPtpStatsIngPtpDrop
The number of PTP packets dropped at ingress by the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.3
esmPtpStatsIngPtpPigBag
The number of PTP Piggy Bag added to ingress packets in the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.4
esmPtpStatsEgrPtpv2
The number of PTP V2 packets egress from the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.5
esmPtpStatsEgrPtpv1
The number of PTP V1 packets egress from the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.6
esmPtpStatsEgrPtpDrop
The number of PTP packets dropped at egress by the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.7
esmPtpStatsEgrPtpUpdateRes
The number of PTP residence time updated packets in the port
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.13.1.8

esmStackPortTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14 · 1 row entry · 25 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk esmStackPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::esmStackPortTable' 
A list of Stacking Link statistics
esmStackPortConfEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1
A collection of statistics kept for a Stacking Link.
Indexes
Column Syntax OID
esmStackPortIfIndex
A unique value, greater than zero, for each stack port interface.
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.1
esmStackPortSlotNum
The on-board slot number of stack ports.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.2
esmStackPortInOctets
The total number of octets received on the stacking interface,
including framing characters.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.3
esmStackPortOutOctets
The total number of octets transmitted out of the
stacking interface, including framing characters.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.4
esmStackPortInUcastPkts
The number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were not addressed to a multicast
or broadcast address at this sub-layer.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.5
esmStackPortOutUcastPkts
The total number of packets that higher-level protocols
requested be transmitted, and which were not addressed to a
multicast or broadcast address at this sub-layer, including
those that were discarded or not sent.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.6
esmStackPortInMulticastPkts
The number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were addressed to a multicast
address at this sub-layer. For a MAC layer protocol, this
includes both Group and Functional addresses.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.7
esmStackPortOutMulticastPkts
The total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a
multicast address at this sub-layer, including those that
were discarded or not sent. For a MAC layer prot…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.8
esmStackPortInBroadcastPkts
The number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were addressed to a broadcast
address at this sub-layer.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.9
esmStackPortOutBroadcastPkts
The total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a
broadcast address at this sub-layer, including those that
were discarded or not sent.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.10
esmStackPortInPauseFrames
A count of MAC Control frames received on stacking
interface with an opcode indicating the PAUSE operation.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.11
esmStackPortOutPauseFrames
A count of MAC Control frames transmitted on
stacking interface with an opcode indicating the
PAUSE operation.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.12
esmStackPortStatsAlignmentErrors
A count of frames received on the stacking
interface that are not an integral number of
octets in length and do not pass the FCS check.

The count represented by an instance of this
object is incremented w…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.13
esmStackPortStatsFCSErrors
A count of frames received on the stacking
interface that are an integral number of octets
in length but do not pass the FCS check. This
count does not include frames received with
frame-too-long or frame-too-short err…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.14
esmStackPortInErrors
For a stacking interface, the number of inbound packets that
contained errors preventing them from being deliverable
to a higher-layer protocol. For character-oriented or
fixed-length interfaces, the number of inbou…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.15
esmStackPortOutErrors
For a stacking interface, the number of outbound packets
that could not be transmitted because of errors.
For character-oriented or fixed-length interfaces, the
number of outbound transmission units that could no…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.16
esmStackPortInDiscards
The number of inbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being deliverable to a higher-layer protocol. One
possible reason for discarding such a packet co…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.17
esmStackPortOutDiscards
The number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being transmitted. One possible reason for discarding
such a packet could be to free up buffer s…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.18
esmStackPortTxCollisions
The estimate of the total number of collisions.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.19
esmStackPortRxUndersizePkts
The total number of packets received that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.20
esmStackPortTxUndersizePkts
The total number of packets transmitted that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.21
esmStackPortRxOversizePkts
The total number of packets received that were
longer than 1518 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.22
esmStackPortTxOversizePkts
The total number of packets transmitted that were
longer than 1518 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.23
esmStackPortAutoSpeed
The automatically detected port line speed
of the stack port.
Enumeration
Enumerated Values:
1speed100
2speed10
3speedAuto
4unknown
5speed1000
6speed10000
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.24
esmStackPortClearStats
Used to Clear all Stack Port Statistics counters.
By default, this object contains zero value.
Enumerationr/w
Enumerated Values:
0default
1reset
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.14.1.25

alaPortViolationRecoveryTable

table
.1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.5 · 1 row entry · 2 columns
Open in standard view
Uses the alcatel variant from /opt/observium/mibs/alcatel.
Command help
Walk alaPortViolationRecoveryTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ALCATEL-IND1-PORT-MIB' -M '/opt/observium/mibs/alcatel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ALCATEL-IND1-PORT-MIB::alaPortViolationRecoveryTable' 
A list of Interface Violation Recovery Configuration Parameters
alaPortViolationRecoveryEntry row .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.5.1
A collection of Interface Violation Recovery configurations kept for a particular
Ethernet interface.
Indexes
Column Syntax OID
alaPortViolationRecoveryTime
-1 - value in scalar object esmViolationRecoveryTime
0 - Disable the timer
30 - 600 - timeout value to re-enable the ports that have been shutdown
Integer32r/w
Constraints:
range: -1-600
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.5.1.1
alaPortViolationRecoveryMaximum
-1 - value in scalar object esmViolationRecoveryMaximum
0 - recovery mechanism is disabled
1 - 50 - The maximum number of recovery attempts before a port is shudown.
Integer32r/w
Constraints:
range: -1-50
 .1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.5.1.2