zhoneVdslLineConfUpGinpShineRatio
ZhoneVdsl-MIB ·
.1.3.6.1.4.1.5504.5.13.1.1.11.1.139
Object
column
r/w
ratio Unsigned32
gInpShineRatio - The upstream loss of rate in a 1 second interval expressed as a fraction of NDR due to a single high impulse noise event (SHINE) impulse noise environment expected by the operator to occur at a probability acceptable for the services. The valid values are all multiples of 0.001 from 0 to 0.1. This field uses 1 to equal 0.001 and 100 to equal 0.1. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
Context
- MIB
- ZhoneVdsl-MIB
- OID
.1.3.6.1.4.1.5504.5.13.1.1.11.1.139- Type
- column
- Access
- readwrite
- Status
- current
- Units
- ratio
- Parent
- zhoneVdslLineConfProfileEntry
- Table
- zhoneVdslLineConfProfileTable
- Siblings
- 153
Syntax
ratio Unsigned32
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zhoneVdslLineConfProfileName This object identifies a row in this table.
A default profile with an index of 'DEFVAL', will
always exist and its parameters will be set to vendor
specific values,… | column | OctetString | .1.3.6.1.4.1.5504.5.13.1.1.11.1.1 |
| zhoneVdslLineConfUpMinSnrMgn Specifies the minimum upstream Signal/Noise Margin
in units of 0.10 dB, for a range of 0 to 31.0 dB. | column | 0.10dBm Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.10 |
| zhoneVdslLineConfDownBitSwap Enable or disable downstream bit swap. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.100 |
| zhoneVdslLineConfUpBitSwap Enable or disable upstream bit swap. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.101 |
| zhoneVdslLineConfAdslAnnexMModeEnabled This object indicates whether Annex-M mode is enabled
on the Adsl modem. If this object is set to 'true' then
Annex-M mode is enabled. If it is set to 'false then
Annex-M mode i… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.5504.5.13.1.1.11.1.102 |
| zhoneVdslLineConfAdslAnnexMPsdMask This object specifies the maximum transmit PSD
allowed in the downstream channel on an BIS
Annex-M line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.103 |
| zhoneVdslLineConfUs0BoundaryTone This object configures the upper boundary of US0.
US0 is used in long reach mode when there is no more
capacity in US1. The switchover is typically around
3500 feet. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.104 |
| zhoneVdslLineConfDownInp The minimum impulse noise protection for the downstream
bearer channel expressed in symbols. One symbol equals
250 uS. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.105 |
| zhoneVdslLineConfUpInp The minimum impulse noise protection for the upstream
bearer channel expressed in symbols. One symbol equals
250 uS. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.106 |
| zhoneVdslLineConfDownMaxInterleavingDelay The maximum inteleaving delay in the downstream direction.
A value of zero indicates no delay introduced. | column | milliseconds Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.107 |
| zhoneVdslLineConfUpMaxInterleavingDelay The maximum inteleaving delay in the upstream direction.
A value of zero indicates no delay introduced. | column | milliseconds Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.108 |
| zhoneVdslLineConfDownPsdMaskEnable This object selects the Psd Mask in the downstream direction.
'standard' : use the PSD Mask specified in the object
zhoneVdslLineConfDownPsdSelect
… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.109 |
| zhoneVdslLineConfUpTargetSnrMgn Specifies the target upstream Signal/Noise Margin in
units of 0.10 dB, for a range of 0 to 31.0 dB. This
is the Noise Margin the transceivers must achieve with
a BER of 10^-7 or … | column | 0.10dBm Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.11 |
| zhoneVdslLineConfUpPsdMaskEnable This object selects the Psd Mask in the upstream direction.
'standard' : use the PSD Mask specified in the object
zhoneVdslLineConfDownPsdSelect
… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.110 |
| zhoneVdslLineConfDownPsdMaskSelect This object selects one of the standards based PSD mask for the
downstream direction. The object zhoneVdslLineConfDownPsdMaskEnable
must be set to 'standard' for this object to … | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.111 |
| zhoneVdslLineConfUpPsdMaskSelect This object selects one of the standards based PSD mask for the
upstream direction. The object zhoneVdslLineConfUpPsdMaskEnable
must be set to 'standard' for this object to be ac… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.112 |
| zhoneVdslLineEnableTrellisCoding Enables/disables Trellis coding. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.5504.5.13.1.1.11.1.113 |
| zhoneVdslLineEnableRsCoding Enables/disables Rs coding. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.5504.5.13.1.1.11.1.114 |
| zhoneVdslLineConfPsdShape Maximum transmit PSD allowed on a VDSL2 line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.115 |
| zhoneVdslLineConfDownPhyRSupport Enable or disable downstream PHYR.
Only supported by Broadcom PHYR ports. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.116 |
| zhoneVdslLineConfUpPhyRSupport Enable or disable upstream PHYR.
Only supported by Broadcom PHYR ports. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.117 |
| zhoneVdslLineConfDownPhyRmaxINP PHYR maximum downstream impulse noise protection.
A value of 0 specifies no protection.
The values 5 through 160 specify the number of
symbols i… | column | Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.118 |
| zhoneVdslLineConfUpPhyRmaxINP PHYR maximum upstream impulse noise protection.
A value of 0 specifies no protection.
The values 5 through 160 specify the number of
symbols in … | column | Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.119 |
| zhoneVdslLineConfDownFastMaxDataRate Specifies the maximum downstream fast channel
data rate in steps of 1000 bits/second. | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.12 |
| zhoneVdslLineConfDownPhyRminRSoverhead PHYR minimum downstream RS overhead.
Only supported by Broadcom PHYR ports. | column | Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.120 |
| zhoneVdslLineConfUpPhyRminRSoverhead PHYR minimum upstream RS overhead.
Only supported by Broadcom PHYR ports. | column | Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.121 |
| zhoneVdslLineConfDownPhyRRtxRatio PHYR minimum downstream fraction of the
line rate allocated for retransmission.
Only supported by Broadcom PHYR ports. | column | Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.122 |
| zhoneVdslLineConfUpPhyRRtxRatio PHYR minimum upstream fraction of the
line rate allocated for retransmission.
Only supported by Broadcom PHYR ports. | column | Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.123 |
| zhoneVdslLineConfUpPboPsdParamA3 Upstream power backoff PSD parameter A3. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.124 |
| zhoneVdslLineConfUpPboPsdParamA4 Upstream power backoff PSD parameter A4. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.125 |
| zhoneVdslLineConfUpPboPsdParamB3 Upstream power backoff PSD parameter B3. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.126 |
| zhoneVdslLineConfUpPboPsdParamB4 Upstream power backoff PSD parameter B4. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.127 |
| zhoneVdslLineConfFallbackDefaultVpi ATM VPI to be used by the line when it trains
in ADSL/ATM mode and bridges are configured for
single-vc mode | column | Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.128 |
| zhoneVdslLineConfFallbackDefaultVci ATM VCI to be used by the line when it trains
in ADSL/ATM mode and bridges are configured for
single-vc mode | column | Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.129 |
| zhoneVdslLineConfDownFastMinDataRate Specifies the minimum downstream fast channel
data rate in steps of 1000 bits/second. | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.13 |
| zhoneVdslLineConfDownGinpSupport Enable or disable downstream G.INP / ITU-G.998.4.
Only supported by Broadcom ports. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.130 |
| zhoneVdslLineConfUpGinpSupport Enable or disable upstream G.INP / ITU-G.998.4.
Only supported by Broadcom ports. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.131 |
| zhoneVdslLineConfDownGinpEtrMax gInpEtrMax - Maximum allowed value for downstream expected throughput
(ETR) in kbit/s. The valid values are all multiples of 8 from 0 to
the maximum of the valid values of the m… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.132 |
| zhoneVdslLineConfUpGinpEtrMax gInpEtrMax - Maximum allowed value for upstream expected throughput
(ETR) in kbit/s. The valid values are all multiples of 8 from 0 to
the maximum of the valid values of the max… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.133 |
| zhoneVdslLineConfDownGinpEtrMin gInpEtrMin - Minimum allowed value for downstream expected throughput
(ETR) in kbit/s. The valid values are all multiples of 8 from 0 to
the maximum of the valid values of the mi… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.134 |
| zhoneVdslLineConfUpGinpEtrMin gInpEtrMin - Minimum allowed value for upstream expected throughput
(ETR) in kbit/s. The valid values are all multiples of 8 from 0 to
the maximum of the valid values of the mini… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.135 |
| zhoneVdslLineConfDownGinpNdrMax gInpNdrMax - Maximum allowed value for downstream net data rate (NDR)
in kbit/s. The valid values are all multiples of 8 from 0 to the
maximum of the valid values of the maximum … | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.136 |
| zhoneVdslLineConfUpGinpNdrMax gInpNdrMax - Maximum allowed value for upstream net data rate (NDR)
in kbit/s. The valid values are all multiples of 8 from 0 to the
maximum of the valid values of the maximum ne… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.137 |
| zhoneVdslLineConfDownGinpShineRatio gInpShineRatio - The downstream loss of rate in a 1 second interval
expressed as a fraction of NDR due to a single high impulse noise
event (SHINE) impulse noise environment exp… | column | ratio Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.138 |
| zhoneVdslLineConfDownSlowMaxDataRate Specifies the maximum downstream slow channel
data rate in steps of 1000 bits/second.
The maximum aggregate downstream transmit speed
of the line can be derived fro… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.14 |
| zhoneVdslLineConfDownGinpLeftrThreshold gInpLeftrThreshold - The downstream rate Threshold below which the
Low Error Free Rate (LEFTR) defect is declared. The threshold used
to declare leftr defects is expressed in fr… | column | ratio Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.140 |
| zhoneVdslLineConfUpGinpLeftrThreshold gInpLeftrThreshold - The upstream rate Threshold below which the
Low Error Free Rate (LEFTR) defect is declared. The threshold used
to declare leftr defects is expressed in frac… | column | ratio Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.141 |
| zhoneVdslLineConfDownGinpMaxDelay gInpMaxDelay - The maximum downstream delay in ms. This is the upper
limit for the delay that is added to the transmission delay only caused
by retransmissions. Here the receive… | column | mSecs Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.142 |
| zhoneVdslLineConfUpGinpMaxDelay gInpMaxDelay - The maximum upstream delay in ms. This is the upper
limit for the delay that is added to the transmission delay only caused
by retransmissions. Here the receiver … | column | mSecs Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.143 |
| zhoneVdslLineConfDownGinpMinDelay gInpMinDelay - The minimum downstream delay in ms. This is the lower
limit for the delay that is added to the transmission delay caused by
retransmissions only. The time stamp s… | column | mSecs Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.144 |
| zhoneVdslLineConfUpGinpMinDelay gInpMinDelay - The minimum upstream delay in ms. This is the lower
limit for the delay that is added to the transmission delay caused by
retransmissions only. The time stamp sha… | column | mSecs Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.145 |
| zhoneVdslLineConfDownGinpMin ginpMin - The minimum downstream impulse noise protection (INP) against
single high impulse noise event (SHINE) in discrete multitone (DMT)
symbols. The valid values are all int… | column | symbols Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.146 |
| zhoneVdslLineConfUpGinpMin ginpMin - The minimum upstream impulse noise protection (INP) against
single high impulse noise event (SHINE) in discrete multitone (DMT)
symbols. The valid values are all integ… | column | symbols Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.147 |
| zhoneVdslLineConfDownGinpMinRSoverhead gInpMinRSoverhead - This value specifies the downstream bandwidth
reserved for RS (reed-solomon) codewords. The minimum guaranteed R/N
ratio. The unit is 1/256th and the range i… | column | ratio Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.148 |
| zhoneVdslLineConfUpGinpMinRSoverhead gInpMinRSoverhead - This value specifies the upstream bandwidth
reserved for RS (reed-solomon) codewords. The minimum guaranteed R/N
ratio. The unit is 1/256th and the range is … | column | ratio Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.149 |
| zhoneVdslLineConfDownSlowMinDataRate Specifies the minimum downstream slow channel
data rate in steps of 1000 bits/second.
The minimum aggregate downstream transmit speed
of the line can be derived fro… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.15 |
| zhoneVdslLineConfDownGinpReinCfg gInpReinCfg - The minimum downstream impulse protection against
electrical repetitive impulse noise (REIN) in DMT symbols. The valid
values are all integers from 0 to 7 for syst… | column | symbols Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.150 |
| zhoneVdslLineConfUpGinpReinCfg gInpReinCfg - The minimum upstream impulse protection against
electrical repetitive impulse noise (REIN) in DMT symbols. The valid
values are all integers from 0 to 7 for system… | column | symbols Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.151 |
| zhoneVdslLineConfDownGinpReinFreq ginpReinFreq specifies the frequency of REIN inter-arrival time. It is used
in the Channel Initialization Policy and on-line reconfiguration procedures.
REIN is commonly coupled… | column | Hz Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.152 |
| zhoneVdslLineConfUpGinpReinFreq ginpReinFreq specifies the frequency of REIN inter-arrival time. It is used
in the Channel Initialization Policy and on-line reconfiguration procedures.
REIN is commonly coupled… | column | Hz Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.153 |
| zhoneVdslLineConfDownGinpRtxMode gInpRtxMode - Downstream retransmission Mode (RTX MODE). The RTX_MODE
is a configuration parameter used to control activation of retransmission
during initialization. This parame… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.154 |
| zhoneVdslLineConfUpGinpRtxMode gInpRtxMode - Upstream retransmission Mode (RTX MODE). The RTX_MODE
is a configuration parameter used to control activation of retransmission
during initialization. This paramete… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.155 |
| zhoneVdslLineConfUpFastMaxDataRate Specifies the maximum upstream fast channel
data rate in steps of 1000 bits/second.
The maximum aggregate upstream transmit speed
of the line can be derived from th… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.16 |
| zhoneVdslLineConfUpFastMinDataRate Specifies the minimum upstream fast channel
data rate in steps of 1000 bits/second.
The minimum aggregate upstream transmit speed
of the line can be derived from th… | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.17 |
| zhoneVdslLineConfUpSlowMaxDataRate Specifies the maximum upstream slow channel
data rate in steps of 1000 bits/second. | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.18 |
| zhoneVdslLineConfUpSlowMinDataRate Specifies the minimum upstream slow channel
data rate in steps of 1000 bits/second. | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.19 |
| zhoneVdslLineConfDownRateMode Specifies the rate selection behavior for the line
in the downstream direction.
manual(1) forces the rate to the configured rate
adaptAtInit(2) adapts the li… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.2 |
| zhoneVdslLineConfDownRateRatio For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the rat… | column | percent Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.20 |
| zhoneVdslLineConfUpRateRatio For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the rat… | column | percent Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.21 |
| zhoneVdslLineConfDownMaxInterDelay Specifies the maximum interleave delay for the
downstream slow channel. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.22 |
| zhoneVdslLineConfUpMaxInterDelay Specifies the maximum interleave delay for the
upstream slow channel. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.23 |
| zhoneVdslLineConfDownPboControl Downstream power backoff (PBO) control for this
line. For transceivers which do not support downstream
PBO control, this object MUST be fixed at disabled(1).
If auto(2) is select… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.24 |
| zhoneVdslLineConfUpPboControl Upstream power backoff (PBO) control for this
line. For transceivers which do not support upstream
PBO control, this object MUST be fixed at disabled(1).
If auto(2) is selected, … | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.25 |
| zhoneVdslLineConfDownPboLevel Specifies the downstream backoff level to be used
when vdslLineConfDownPboControl = manual(3). | column | 0.25dB Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.26 |
| zhoneVdslLineConfUpPboLevel Specifies the upstream backoff level to be used
when vdslLineConfUpPboControl = manual(3). | column | 0.25dB Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.27 |
| zhoneVdslLineConfDeploymentScenario The VDSL line deployment scenario. When using
fttCab(1), the VTU-C is located in a street cabinet.
When using fttEx(2), the VTU-C is located at the
central office. Changes to th… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.28 |
| zhoneVdslLineConfAdslPresence Indicates presence of ADSL service in the associated
cable bundle/binder.
none(1) indicates no ADSL service in the bundle
adslOverPots(2) indicates ADSL ser… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.29 |
| zhoneVdslLineConfUpRateMode Specifies the rate selection behavior for the line
in the upstream direction.
manual(1) forces the rate to the configured rate
adaptAtInit(2) adapts the line… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.3 |
| zhoneVdslLineConfApplicableStandard The VDSL standard to be used for the line.
ansi(1) indicates ANSI standard
etsi(2) indicates ETSI standard
itu(3) indicates ITU standard
other(4) … | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.30 |
| zhoneVdslLineConfBandPlan The VDSL band plan to be used for the line.
bandPlan997(1) is to be used for
ITU-T G.993.1 Bandplan-B
ETSI Bandplan
ANSI Plan 997
band… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.31 |
| zhoneVdslLineConfBandPlanFx The frequency limit between bands D2 and U2 when
zhoneVdslLineConfBandPlan is set to bandPlanFx(3). | column | kHz Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.32 |
| zhoneVdslLineConfBandOptUsage Defines the VDSL link use of the optional frequency
range [25kHz - 138kHz] (Opt).
unused(1) indicates Opt is unused
upstream(2) indicates Opt usage is for ups… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.33 |
| zhoneVdslLineConfUpPsdTemplate This object has been modified by Zhone.
The upstream PSD template to be used for the line.
Here, templateMask1(1) refers to a notched mask that
limits the transmitt… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.34 |
| zhoneVdslLineConfDownPsdTemplate This object has been modified by Zhone.
The downstream PSD template to be used for the line.
Here, templateMask1(1) refers to a notched mask that
limits the transmi… | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.35 |
| zhoneVdslLineConfHamBandMask The transmit power spectral density mask code, used
to avoid interference with HAM (Handheld Amateur Radio)
radio bands by introducing power control (notching) in one
or more of t… | column | Bits | .1.3.6.1.4.1.5504.5.13.1.1.11.1.36 |
| zhoneVdslLineConfCustomNotch1Start Specifies the start frequency of custom HAM (Handheld
Amateur Radio) notch 1. zhoneVdslLineConfCustomNotch1Start MUST
be less than or equal to vdslLineConfCustomNotch1Stop. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.37 |
| zhoneVdslLineConfCustomNotch1Stop Specifies the stop frequency of custom HAM (Handheld
Amateur Radio) notch 1. zhoneVdslLineConfCustomNotch1Stop MUST
be greater than or equal to vdslLineConfCustomNotch1Start. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.38 |
| zhoneVdslLineConfCustomNotch2Start Specifies the start frequency of custom HAM (Handheld
Amateur Radio) notch 2. zhoneVdslLineConfCustomNotch2Start MUST
be less than or equal to vdslLineConfCustomNotch2Stop. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.39 |
| zhoneVdslLineConfDownMaxPwr Specifies the maximum aggregate downstream power
level in the range -5.0 to 20.0 dBm. | column | 0.10dBm Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.4 |
| zhoneVdslLineConfCustomNotch2Stop Specifies the stop frequency of custom HAM (Handheld
Amateur Radio) notch 2. zhoneVdslLineConfCustomNotch2Stop MUST
be greater than or equal to vdslLineConfCustomNotch2Start. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.40 |
| zhoneVdslLineConfDownTargetSlowBurst Specifies the target level of impulse noise (burst)
protection for an interleaved (slow) channel. | column | microseconds Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.41 |
| zhoneVdslLineConfUpTargetSlowBurst Specifies the target level of impulse noise (burst)
protection for an interleaved (slow) channel. | column | microseconds Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.42 |
| zhoneVdslLineConfDownMaxFastFec This parameter provisions the maximum level of Forward
Error Correction (FEC) redundancy related overhead to
be maintained for a fast channel. | column | % Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.43 |
| zhoneVdslLineConfUpMaxFastFec This parameter provisions the maximum level of Forward
Error Correction (FEC) redundancy related overhead to
be maintained for a fast channel. | column | % Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.44 |
| zhoneVdslLineConfLineType This parameter provisions the VDSL physical entity at
start-up by defining whether and how the line will be
channelized, i.e., which channel type(s) are supported.
If the line is … | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.45 |
| zhoneVdslLineConfProfRowStatus This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to 'active'.
When 'active' is … | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.5504.5.13.1.1.11.1.47 |
| zhoneVdslLineConfTransmissionMode The transmission standard to be used for the line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.48 |
| zhoneVdslLineConfVdsl2Profile The VDSL2 standard to be used for the line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.49 |
| zhoneVdslLineConfUpMaxPwr Specifies the maximum aggregate upstream power
level in the range -13.0 to 20.0 dBm. | column | 0.10dBm Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.5 |
| zhoneVdslLineConfVdslMode Controls which VDSL modes are available on the line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.50 |
| zhoneVdslLineConfPboElectricalOverride Override electrical length estimated by VUTU_C.
The special value 256 means do not perform
override. | column | .5 dBm/Mhz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.51 |
| zhoneVdslLineConfAutoModeCrtrn Determines the policy to select optimal mode of oepration. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.52 |
| zhoneVdslLineConfNetworkTimingRef Enable/disable reference clock source. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.53 |
| zhoneVdslLineConfAdslBandMode Specifies whether the XDSL can use the ADSL spectrum or not. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.54 |
| zhoneVdslLineConfAdslBandModeEndFreq Specifies the ADSL band end frequency when
the ADSL band usage is not allowed. | column | kHz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.55 |
| zhoneVdslLineConfSeltEchoMeasurementTime Contains the SELT echo measurement time | column | secs Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.56 |
| zhoneVdslLineConfSeltNoiseMeasurementTime Contains the SELT noise measurement time. | column | secs Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.57 |
| zhoneVdslLineConfSeltAgc Contains the SELT AGC gain value. | column | 1 dBm Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.58 |
| zhoneVdslLineConfDownTrellis Enables/disables downstream Trellis coding. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.59 |
| zhoneVdslLineConfDownMaxSnrMgn Specifies the maximum downstream Signal/Noise Margin
in units of 0.10 dB, for a range of 0 to 31.0 dB. | column | 0.10dBm Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.6 |
| zhoneVdslLineConfUpTrellis Enables/disables upstream Trellis coding. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.60 |
| zhoneVdslLineConfDownMaxAggregateTxPwr Maximum total power that is allowed to be transmitted
in the downstream direction. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.61 |
| zhoneVdslLineConfUpMaxAggregateTxPwr Maximum total power that is allowed to be transmitted
in the upstream direction. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.62 |
| zhoneVdslLineConfDownMaxPsd The maximum power spectral density level
allowed on the line at the transmitter
output downstream for initialization and
showtime signals. | column | .1 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.63 |
| zhoneVdslLineConfUpMaxPsd The maximum power spectral density level
allowed on the line at the transmitter
output upstream for initialization and
showtime signals. | column | .1 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.64 |
| zhoneVdslLineConfDownPsdShape Maximum transmit PSD allowed in the downstream
channel on a VDSL2 line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.65 |
| zhoneVdslLineConfUpPsdShape Maximum transmit PSD allowed in the upstream
channel on a VDSL2 line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.66 |
| zhoneVdslLineConfDownVirtualNoiseSnrMode Downstream virtual noise SNR mode on a VDSL2
line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.67 |
| zhoneVdslLineConfUpVirtualNoiseSnrMode Upstream virtual noise SNR mode on a VDSL2
line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.68 |
| zhoneVdslLineConfDownErasureDetectionFast Indicates whether the erasure detection
mechanism should be enabled or disabled in
the downstream fast channel. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.69 |
| zhoneVdslLineConfDownMinSnrMgn Specifies the minimum downstream Signal/Noise Margin
in units of 0.10 dB, for a range of 0 to 31.0 dB. | column | 0.10dBm Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.7 |
| zhoneVdslLineConfUpErasureDetectionFast Indicates whether the erasure detection
mechanism should be enabled or disabled in
the downstream fast channel. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.70 |
| zhoneVdslLineConfDownErasureDetectionInterleave Indicates whether the erasure detection
mechanism should be enabled or disabled in
the downstream slow channel (interleave). | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.71 |
| zhoneVdslLineConfUpErasureDetectionInterleave Indicates whether the erasure detection
mechanism should be enabled or disabled in
the uptream slow channel (interleave). | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.72 |
| zhoneVdslLineConfDownGhsA43TonePwr Determines the mode of the downstream tones
power used during handshake, during A43
mode. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.73 |
| zhoneVdslLineConfDownGhsB43TonePwr Determines the mode of the downstream tones
power used during handshake, during B43
mode. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.74 |
| zhoneVdslLineConfDownGhsA43cTonePwr Determines the mode of the downstream tones
power used during handshake, during A43c
mode. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.75 |
| zhoneVdslLineConfDownGhsV43TonePwr Determines the mode of the downstream tone
power used during handshake, during V43
mode. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.76 |
| zhoneVdslLineConfDownGhsA43TonePwrMaxLvl Determines the maximum power of downstream
tones used, in manual mode, during handshake
in A43 mode. A value of -99 indicates no
power used. | column | 0.5 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.77 |
| zhoneVdslLineConfDownGhsB43TonePwrMaxLvl Determines the maximum power of downstream
tones used, in manual mode, during handshake
in B43 mode. A value of -99 indicates no
power used. | column | 0.5 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.78 |
| zhoneVdslLineConfDownGhsA43cTonePwrMaxLvl Determines the maximum power of downstream
tones used, in manual mode, during handshake
in A43c mode. A value of -99 indicates no
power used. | column | 0.5 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.79 |
| zhoneVdslLineConfDownTargetSnrMgn Specifies the target downstream Signal/Noise Margin
in units of 0.10 dB, for a range of 0 to 31.0 dB.
This is the Noise Margin the transceivers must achieve
with a BER of 10^-7 or… | column | 0.10dBm Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.8 |
| zhoneVdslLineConfDownGhsV43TonePwrMaxLvl Determines the maximum power of downstream
tones used, in manual mode, during handshake
in V43 mode. A value of -99 indicates no
power used. | column | 0.5 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.80 |
| zhoneVdslLineConfDownRsCoding Parameter to enable/disable RS Coding in
downstream channel. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.81 |
| zhoneVdslLineConfUpRsCoding Parameter to enable/disable RS Coding in
upsream channel. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.82 |
| zhoneVdslLineConfUpPboPsdTemplate Specifies the maximum received PSD allowed
in the upstream channel on the VDSLx line. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.83 |
| zhoneVdslLineConfUpPboPsdParamA1 Upstream power backoff PSD parameter A1. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.84 |
| zhoneVdslLineConfUpPboPsdParamA2 Upstream power backoff PSD parameter A2. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.85 |
| zhoneVdslLineConfUpPboPsdParamB1 Upstream power backoff PSD parameter B1. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.86 |
| zhoneVdslLineConfUpPboPsdParamB2 Upstream power backoff PSD parameter B2. This
parameter is only used if the mask selection
is set to PSDMaskABParameters | column | .01 dBm/Hz Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.87 |
| zhoneVdslLineConfDownDownshiftSnrMgn Configured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate. | column | tenth dB Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.88 |
| zhoneVdslLineConfDownUpshiftSnrMgn Configured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate. | column | tenth dB Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.89 |
| zhoneVdslLineConfUpMaxSnrMgn Specifies the maximum upstream Signal/Noise Margin
in units of 0.10 dB, for a range of 0 to 31.0 dB. | column | 0.10dBm Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.9 |
| zhoneVdslLineConfDownMinDownshiftTime Minimum time that the current margin is below
DownshiftSnrMgn before a downshift occurs. | column | seconds Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.90 |
| zhoneVdslLineConfDownMinUpshiftTime Minimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs. | column | seconds Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.91 |
| zhoneVdslLineConfUpDownshiftSnrMgn Configured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate. | column | tenth dB Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.92 |
| zhoneVdslLineConfUpUpshiftSnrMgn Configured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate. | column | tenth dB Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.93 |
| zhoneVdslLineConfUpMinDownshiftTime Minimum time that the current margin is below
DownshiftSnrMgn before a downshift occurs. | column | seconds Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.94 |
| zhoneVdslLineConfUpMinUpshiftTime Minimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs. | column | seconds Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.95 |
| zhoneVdslLineConfDownMinTxThresholdAlarm Minimum CO Tx Sync rate threshold alarm. If set to 0,
this field is disregarded. Otherwise, if Tx Sync
rate falls below this value, a trap and alarm will
be issued | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.96 |
| zhoneVdslLineConfUpMinTxThresholdAlarm Minimum CPE Tx Sync rate threshold alarm. If set to 0,
this field is disregarded. Otherwise, if Tx Sync
rate falls below this value, a trap and alarm will
be issued | column | kbps Unsigned32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.97 |
| zhoneVdslLineConfPotsBypassRelayMaxDuration The maximum duration in seconds that an Adsl Pots Low
Pass Filter Bypass Relay will remain active (meaning
closed/energized). As a fail-safe mechanism, the relay
will automaticall… | column | secs Integer32 | .1.3.6.1.4.1.5504.5.13.1.1.11.1.98 |
| zhoneVdslLineConfDMTConfMode Discrete Multi-Tone parameter that selects whether there
is overlap (echoCancel) or no overlap (freqDivMux) of bins. | column | Enumeration | .1.3.6.1.4.1.5504.5.13.1.1.11.1.99 |