zxDsx1Fdl
ZXDS1-MIB ·
.1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.13
Object
column
r/w
Integer32
This bitmap describes the use of the facilities
data link, and is the sum of the capabilities.
Set any bits that are appropriate:
other(1),
dsx1AnsiT1403(2),
dsx1Att54016(4),
dsx1FdlNone(8)
'other' indicates that a protocol other than
one following is used.
'dsx1AnsiT1403' refers to the FDL exchange
recommended by ANSI.
'dsx1Att54016' refers to ESF FDL exchanges.
'dsx1FdlNone' indicates that the device does
not use the FDL.
Context
- MIB
- ZXDS1-MIB
- OID
.1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- zxDsx1ConfigEntry
- Table
- zxDsx1ConfigTable
- Siblings
- 30
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-15
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxDsx1LineIndex This object should be made equal to ifIndex. The
next paragraph describes its previous usage.
Making the object equal to ifIndex allows proper
use of ifStackTable and ds0/ds0bund… | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.1 |
| zxDsx1LineStatus This variable indicates the Line Status of the
interface. It contains loopback, failure,
received 'alarm' and transmitted 'alarms
information.
The zxDsx1LineStatus… | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.10 |
| zxDsx1SignalMode 'none' indicates that no bits are reserved for
signaling on this channel.
'robbedBit' indicates that DS1 Robbed Bit Signaling
is in use.
'bitOriented… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.11 |
| zxDsx1TransmitClockSource The source of Transmit Clock.
'loopTiming' indicates that the recovered
receive clock is used as the transmit clock.
'localTiming' indicates that a local clock
sour… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.12 |
| zxDsx1InvalidIntervals The number of intervals in the range from 0 to
zxDsx1ValidIntervals for which no data is available.
This object will typically be zero except in cases
where the data for some inte… | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.14 |
| zxDsx1LineLength The length of the ds1 line in meters. This
objects provides information for line build out
circuitry. This object is only useful if the
interface has configurable line build out
… | column | meters Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.15 |
| zxDsx1LineStatusLastChange The value of MIB II's sysUpTime object at the
time this DS1 entered its current line status
state. If the current state was entered prior to
the last re-initialization of the pro… | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.16 |
| zxDsx1LineStatusChangeTrapEnable Indicates whether dsx1LineStatusChange traps
should be generated for this interface. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.17 |
| zxDsx1LoopbackStatus This variable represents the current state of the
loopback on the DS1 interface. It contains
information about loopbacks established by a
manager and remotely from the far end.
… | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.18 |
| zxDsx1Ds1ChannelNumber This variable represents the channel number of
the DS1/E1 on its parent DS2/E2 or DS3/E3. A
value of 0 indicated this DS1/E1 does not have a
parent DS3/E3. | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.19 |
| zxDsx1IfIndex deprecated This value for this object is equal to the value
of ifIndex from the Interfaces table of MIB II
(RFC 1213). | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.2 |
| zxDsx1Channelization Indicates whether this ds1/e1 is channelized or
unchannelized. The value of enabledDs0 indicates
that this is a DS1 channelized into DS0s. The
value of enabledDs1 indicated that… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.20 |
| zxDsx1LineMode This setting puts the T1 framer into either long
haul (CSU) mode or short haul (DSU) mode. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.21 |
| zxDsx1LineBuildOut Attenuation setting for T1 framer in long haul
(CSU) mode. The optional values are: -7.5dB,
-15dB, -22.5dB and 0dB. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.22 |
| zxDsx1AdminStatus The desired state of the interface. The
testing(3) state indicates that no operational
packets can be passed. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.23 |
| zxDsx1OperStatus The current operational state of the interface.
The testing(3) state indicates that no operational
packets can be passed. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.24 |
| zxDsx1ClockStatus The current clock state of the interface. the value can be:
FREERUN 0
HOLDOVER 1
ACQUIRING 2
ACUIRED 3 | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.25 |
| zxDsx1CfgInfoSend The action to send the configuration on
Ds1/E1 interface to corresponding card. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.26 |
| zxDsx1Retiming Enable or disable Ds1/E1 interface retiming. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.27 |
| zxDsx1Impedance | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.28 |
| zxDsx1FrameType | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.29 |
| zxDsx1TimeElapsed The number of seconds that have elapsed since the
beginning of the near end current error-measurement
period. If, for some reason, such as an adjustment
in the system's time-of-da… | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.3 |
| zxDsx1BER | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.30 |
| zxDsx1ClockStatusTrapEnable Indicates whether zxDsx1ClockStatus traps
should be generated for this interface. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.31 |
| zxDsx1ValidIntervals The number of previous near end intervals for
which data was collected. The value will be 96
unless the interface was brought online within the
last 24 hours, in which case the v… | column | Integer32 | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.4 |
| zxDsx1LineType This variable indicates the variety of DS1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably car… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.5 |
| zxDsx1LineCoding This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx1JBZS refers the Jamm… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.6 |
| zxDsx1SendCode This variable indicates what type of code is
being sent across the DS1 interface by the device.
Setting this variable causes the interface to send
the code requested. The values … | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.7 |
| zxDsx1CircuitIdentifier This variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting. | column | OctetString | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.8 |
| zxDsx1LoopbackConfig This variable represents the desired loopback
configuration of the DS1 interface. Agents
supporting read/write access should return
inconsistentValue in response to a requested
l… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.1.1.1.9 |