zxAnXdsl2SeltCapNoisePsdDs
ZTE-AN-XDSL2-MIBII ·
.1.3.6.1.4.1.3902.1015.1001.1.7.1.1.7
Object
column
r/w
OctetString
Capacity Estimate Noise PSD Downstream.
This configuration parameter defines the PSD template of the
transmit signal to be used in capacity estimate evaluation.
The parameter shall be a set of breakpoints that are represented
by [(t1, PSD1), (t2, PSD2), ..., (tN, PSDN)], each breakpoint
occupies 4 octets and consist of a frequency index tn(2 bytes) and
a signal PSD level(2 bytes).
The range of valid values for index tn is 0 to 8191, and the range
of valid values for PSD is 300 to 2000(units of -0.1dBm/Hz).
The maximum number of breakpoints is 128.
Context
- MIB
- ZTE-AN-XDSL2-MIBII
- OID
.1.3.6.1.4.1.3902.1015.1001.1.7.1.1.7- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- zxAnXdsl2SeltConfEntry
- Table
- zxAnXdsl2SeltConfTable
- Siblings
- 14
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-512
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAnXdsl2LnSeltCmndConfLdsf Command:Loop diagnostics mode forced (LDSF). Defines whether the
line should be forced into the loop diagnostics mode by the
near-end xTU on this line or only be responsive to lo… | column | VDSL2-LINE-TC-MIBXdsl2LineLdsf | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.1 |
| zxAnXdsl2SeltCapTargetSnrmUs Capacity Estimate Target Noise Margin Upstream.
This is the Noise Margin to be used in capacity estimate evaluation,
relative to a BER requirement of 1E-7. | column | 0.1dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.10 |
| zxAnXdsl2SeltUerMeasureEnableC This parameter is a binary variable, where '1' triggers the CO
SELT PMD to start a UER measurement. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.11 |
| zxAnXdsl2SeltQlnMeasureEnableC This parameter is a binary variable, where '1' triggers the CO
SELT PMD to start a QLN measurement. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.12 |
| zxAnXdsl2SeltCalibrateCmd Execute this command to calibrate the parameter that is used to
calculate the SELT result.
When execute this command before SELT, the test result will be
more accurate. | column | VDSL2-LINE-TC-MIBXdsl2LineLdsf | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.13 |
| zxAnXdsl2SeltRawDataCmd Defines whether the line should be forced into SELT raw data
test mode. | column | VDSL2-LINE-TC-MIBXdsl2LineLdsf | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.14 |
| zxAnXdsl2SeltQuickTestEnable Enable/disable the quick SELT test.
enabled(1) - Start the SELT test with quick mode.
disabled(2) - Start the SELT test with normal mode. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.15 |
| zxAnXdsl2SeltUerMmd SELT UER Maximum Measurement Duration.
This parameter is the maximum allowed time for SELT Uncalibrated
Echo Response measurement, between the time of the start command
written … | column | seconds Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.2 |
| zxAnXdsl2SeltQlnMmd SELT Quiet Line Noise Maximum Measurement Duration.
This parameter is the maximum allowed time for SELT quiet line
noise measurement, between the time of the start command
writt… | column | seconds Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.3 |
| zxAnXdsl2SeltCece Capacity Estimate Calculation Enabling.
This parameter specifies if the SELT-P function shall perform the
Downstream capacity and Upstream capacity estimation, if supported. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.4 |
| zxAnXdsl2SeltCapSignalPsdDs Capacity Estimate Signal PSD Downstream.
This configuration parameter defines the PSD template of the
transmit signal to be used in capacity estimate evaluation.
… | column | OctetString | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.5 |
| zxAnXdsl2SeltCapSignalPsdUs Capacity Estimate Signal PSD Upstream.
This configuration parameter defines the PSD template of the
transmit signal to be used in capacity estimate evaluation.
T… | column | OctetString | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.6 |
| zxAnXdsl2SeltCapNoisePsdUs Capacity Estimate Noise PSD Upstream.
This configuration parameter defines the PSD template of the
transmit signal to be used in capacity estimate evaluation.
Th… | column | OctetString | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.8 |
| zxAnXdsl2SeltCapTargetSnrmDs Capacity Estimate Target Noise Margin Downstream.
This is the Noise Margin to be used in capacity estimate evaluation,
relative to a BER requirement of 1E-7. | column | 0.1dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.7.1.1.9 |