zxAnEventDefineEventType
ZTE-AN-EVNET-MIB ·
.1.3.6.1.4.1.3902.1015.190.8.2.1.5
Object
column
Bits
The event type are defined in ITU-T X.733.
- equipment event type:
An event of this type is principally associated with an
equipment fault;
- quality of service event type:
An event of this type is principally associated with a
degradation in the quality of a service;
- communications event type:
An event of this type is principally associated with the
procedures and/or processes required to convey information
from one point to another;
- environmental event type:
An event of this type is principally associated with a
condition relating to an enclosure in which the equipment
resides.
- processing error event type:
An event of this type is principally associated with a
software or processing fault;
Context
- MIB
- ZTE-AN-EVNET-MIB
- OID
.1.3.6.1.4.1.3902.1015.190.8.2.1.5- Type
- column
- Access
- readonly
- Status
- current
- Parent
- zxAnEventDefineEntry
- Table
- zxAnEventDefineTable
- Siblings
- 9
Syntax
Bits
Values & Constraints
Enumerated Values
0 | equipmentEvent |
1 | qualityOfServiceEvent |
2 | communicationsEvent |
3 | environmentEvent |
4 | processingErrorEvent |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAnEventDefineCode Event or alarm code. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.190.8.2.1.1 |
| zxAnEventDefineReversalEnable Enable or disable alarm reversal.
If enable(1), device will not report the alarm generated by an
unused service or managed entity.
But if the service or managed entity is not id… | column | Enumeration | .1.3.6.1.4.1.3902.1015.190.8.2.1.10 |
| zxAnEventDefineReportChannelType Event report channel type.
snmp(1) - event is reported to NMS by SNMP.
ponExtendedOam(2) - event is reported to NMS by EPON extend OAM.
ponOmci(3) - event is repo… | column | Enumeration | .1.3.6.1.4.1.3902.1015.190.8.2.1.2 |
| zxAnEventDefineName Event name. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.3902.1015.190.8.2.1.3 |
| zxAnEventDefineStandardAlarmCode Standard alarm code is just used by events of EPON extend OAM or
GPON OMCI.
Value 0 means SNMP trap. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.190.8.2.1.4 |
| zxAnEventDefineAdminStatus Enables or disables a specified event.
If disable(2), event will not be pushed into alarm pool and
discarded directly. | column | Enumeration | .1.3.6.1.4.1.3902.1015.190.8.2.1.6 |
| zxAnEventDefineMaskEnable Enable or disable the event mask.
If enable(1), event will be pushed into alarm pool, but not be
reported to NMS. At the same time, a message will be sent to NMS
to restore the … | column | Enumeration | .1.3.6.1.4.1.3902.1015.190.8.2.1.7 |
| zxAnEventDefineSendingDelay Event sending delay.
Value 0 means event is sent without delay.
This object is used to prevent that event and restoring event occur
frequently in a short time. | column | seconds Integer32 | .1.3.6.1.4.1.3902.1015.190.8.2.1.8 |
| zxAnEventDefineSendingLimit Limit the number of specified event sending per second.
Value 0 means no limit.
This object is used to prevent sending too many events to NMS at
the same time. | column | seconds Integer32 | .1.3.6.1.4.1.3902.1015.190.8.2.1.9 |