wtWebioEA2x2-24VBinaryTcpServerInputTrigger

Webio-Digital-MIB-US · .1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.3

Object

column mandatory r/w OctetString

Every change on the inputs causes their state to be transmitted to the 
remote device. To minimize data traffic, individual inputs may be exempted 
from this rule. Nevertheless every transmission will contain all input bits.
If a bit is set (1), a change of state on the corresponding input 
triggers a transmission. If the bit is not set (0), no transmission 
takes place.
The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. 
Bit 0 corresponds to the LSB.
OCTET 1: unused
OCTET 2: unused
OCTET 3: unused
OCTET 4, Bit 0-1: Digital inputs 0-1

Context

MIB: Webio-Digital-MIB-US
OID: .1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.3
Type: column
Access: readwrite
Status: mandatory
Parent: wtWebioEA2x2-24VBinaryEntry
Table: wtWebioEA2x2-24VBinaryTable
Siblings: 21

Syntax

OctetString

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
wtWebioEA2x2-24VBinaryOperationMode mandatory Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bi…	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.1`
wtWebioEA2x2-24VBinaryTcpClientInputTrigger mandatory Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless ev…	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.10`
wtWebioEA2x2-24VBinaryTcpClientInterval mandatory Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending.	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.11`
wtWebioEA2x2-24VBinaryTcpClientApplicationMode mandatory Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused …	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.12`
wtWebioEA2x2-24VBinaryUdpPeerLocalPort mandatory Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual).	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.13`
wtWebioEA2x2-24VBinaryUdpPeerRemotePort mandatory Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the remote por…	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.14`
wtWebioEA2x2-24VBinaryUdpPeerRemoteIpAddr mandatory Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the remote devi…	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.15`
wtWebioEA2x2-24VBinaryUdpPeerInputTrigger mandatory Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless ev…	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.16`
wtWebioEA2x2-24VBinaryUdpPeerInterval mandatory Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending.	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.17`
wtWebioEA2x2-24VBinaryUdpPeerApplicationMode mandatory Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused …	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.18`
wtWebioEA2x2-24VBinaryConnectedPort mandatory Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read.	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.19`
wtWebioEA2x2-24VBinaryTcpServerLocalPort mandatory Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual).	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.2`
wtWebioEA2x2-24VBinaryConnectedIpAddr mandatory IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read.	column	RFC1155-SMIIpAddress	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.20`
wtWebioEA2x2-24VBinaryTcpServerClientHttpPort mandatory HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible 50xxx.	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.21`
wtWebioEA2x2-24VBinaryTcpClientServerHttpPort mandatory HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port.	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.22`
wtWebioEA2x2-24VBinaryTcpServerApplicationMode mandatory Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 4-7: unused …	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.4`
wtWebioEA2x2-24VBinaryTcpClientLocalPort mandatory Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual).	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.5`
wtWebioEA2x2-24VBinaryTcpClientServerPort mandatory Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the server port to ze…	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.6`
wtWebioEA2x2-24VBinaryTcpClientServerIpAddr mandatory Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the server IP address …	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.7`
wtWebioEA2x2-24VBinaryTcpClientServerPassword mandatory Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administrator password exis…	column	OctetString	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.8`
wtWebioEA2x2-24VBinaryTcpClientInactivity mandatory Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the timer. Using the Box…	column	Integer32	`.1.3.6.1.4.1.5040.1.2.30.3.1.3.6.3.1.9`

Indexes