sdpNetDomainName
TN-SDP-MIB ·
.1.3.6.1.4.1.7483.6.1.2.4.4.3.1.51
Object
The value of sdpNetDomainName specifies the network-domain name configured on this SDP. The dafault value of this object is the 'default' network-domain.
Context
- MIB
- TN-SDP-MIB
- OID
.1.3.6.1.4.1.7483.6.1.2.4.4.3.1.51- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- sdpInfoEntry
- Table
- sdpInfoTable
- Siblings
- 58
Values & Constraints
Type Constraints
range: 0..32
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sdpId SDP identifier. | column | TN-SERV-MIBSdpId | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.1 |
| sdpAdminPathMtu This object specifies the desired largest service
frame size (in octets) that can be transmitted
through this SDP to the far-end ESR, without
requiring the packet to be fragmented… | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.10 |
| sdpOperPathMtu This object specifies the actual largest service
frame size (in octets) that can be transmitted
through this SDP to the far-end ESR, without
requiring the packet to be fragmented.… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.11 |
| sdpKeepAliveAdminStatus This object is used to enable or disable the
keep-alive protocol used to determine the
operating status of this SDP. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.12 |
| sdpKeepAliveOperStatus The current status of the keep-alive protocol.
The value 'alive' indicates that the far-end
ESR is replying the SDP Echo Requests messages
sent by this device indicating no error … | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.13 |
| sdpKeepAliveHelloTime This object specifies how often the SDP Echo
Request messages are transmitted on this SDP. | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.14 |
| sdpKeepAliveMaxDropCount This object specifies the maximum number of
consecutive SDP Echo Request messages that can
be unacknowledged before the keep-alive
protocol reports a fault. | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.15 |
| sdpKeepAliveHoldDownTime This object specifies the amount of time to
wait before the keep-alive operating status
is eligible to enter the 'alive' state. | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.16 |
| sdpLastMgmtChange The value of sysUpTime at the time of the
most recent management-initiated change to
this SDP. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.17 |
| sdpKeepAliveHelloMessageLength This object specifies the length of the
SDP Echo Request messages transmitted on
this SDP. The default value of zero
indicates that the message length should
be equal to the SDP's… | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.18 |
| sdpKeepAliveNumHelloRequestMessages The number of SDP Echo Request messages
transmitted since the keep-alive was
administratively enabled or the counter
was cleared. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.19 |
| sdpRowStatus This object indicates the status of this row. The
only values supported during a set operation are
'createAndGo' and 'destroy'. To delete an entry
from this table, the correspondi… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.2 |
| sdpKeepAliveNumHelloResponseMessages The number of SDP Echo Response messages
received since the keep-alive was
administratively enabled or the counter
was cleared. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.20 |
| sdpKeepAliveNumLateHelloResponseMessages The number of SDP Echo Response messages
received after the corresponding Request
timeout timer expired. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.21 |
| sdpKeepAliveHelloRequestTimeout The number of seconds to wait for an SDP
Echo Response message before declaring
a timeout. | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.22 |
| sdpLdpEnabled When the value of this object is 'true'
the transport LSP's are signalled by LDP,
as opposed to being provisioned static or
RSVP-signalled LSP's. This object applies
only to MPLS … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.23 |
| sdpVlanVcEtype This object specifies the Ethertype used in
frames sent out this SDP, when the VC type
is vlan. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.24 |
| sdpAdvertisedVllMtuOverride When the value of this object is 'true'
the advertised MTU of a VLL spoke SDP bind
includes the 14-byte L2 header, so that it is
backward compatible with pre-2.0 software. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.25 |
| sdpOperFlags This object specifies all the conditions that
affect the operating status of this SDP. | column | Bits | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.26 |
| sdpLastStatusChange The value of sysUpTime at the time of the
most recent operating status change to this
SDP. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.27 |
| sdpMvplsMgmtService The value of sdpMvplsMgmtService indicates
the service Id of the service where the STP instance
is running that is managing this SDP. This object is
only valid if sdpMvplsMgmtServ… | column | TN-TC-MIBTmnxServId | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.28 |
| sdpMvplsMgmtSdpBndId The value of sdpMvplsMgmtSdpBndId indicates
which SDP bind in the mVPLS instance specified in
sdpMvplsMgmtService is controlling this SDP. This
object is only valid if sdpMvplsMgm… | column | TN-TC-MIBSdpBindId | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.29 |
| sdpDelivery This object specifies the type of delivery used
by this SDP. The value of this
object must be specified when the row is created
and cannot be changed while the row status is
'acti… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.3 |
| sdpCollectAcctStats The value of the object sdpCollectAcctStats specifies
whether the agent collects accounting statistics for this
SDP. When the value is 'true' the agent
collects accounting statist… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.30 |
| sdpAccountingPolicyId The value of sdpAccountingPolicyId specifies the
policy to use to collect accounting statistics on
this SDP. The value zero indicates that the
agent should use the default account… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.31 |
| sdpClassFwdingEnabled The value of sdpClassFwdingEnabled specifies the
admin state of class-based forwarding on this SDP. When
the value is 'true', class-based forwarding is enabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.32 |
| sdpClassFwdingDefaultLsp The value of sdpClassFwdingDefaultLsp specifies the
LSP ID that is used as a default when class-based
forwarding is enabled on this SDP. This object
must be set when enabling clas… | column | TN-TC-MIBTmnxVRtrMplsLspID | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.33 |
| sdpClassFwdingMcLsp The value of sdpClassFwdingMcLsp specifies the LSP ID that
all multicast traffic will be forwarded on when class-based
forwarding is enabled on this SDP. When this object has its
… | column | TN-TC-MIBTmnxVRtrMplsLspID | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.34 |
| sdpMetric The value of sdpMetric specifies the metric to be used
within the Tunnel Table Manager for decision making
purposes. When multiple SDPs going to the same destination
exist, this v… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.35 |
| sdpAutoSdp The value of sdpAutoSdp indicates whether this is an
Auto generated SDP from RADIUS discovery or BGP
auto-discovery. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.36 |
| sdpSnmpAllowed The value of sdpSnmpAllowed indicates if SNMP sets
are allowed on this SDP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.37 |
| sdpPBBEtype This object specifies the Ethertype used in frames sent
out on this SDP when sdpBindVcType is 'vlan' for
Provider Backbone Bridging frames. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.38 |
| sdpBandwidthBookingFactor sdpBandwidthBookingFactor is used to calculate the max
SDP available bandwidth. The value of
sdpBandwidthBookingFactor specifies the percentage of the
SDP max available bandwidth… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.39 |
| sdpFarEndIpAddress This object specifies the IP address of the remote
end of the GRE or MPLS tunnel defined by this SDP.
If sdpTunnelFarEndIpAddress is not set, then
sdpFarEndIpAddress also specifie… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.4 |
| sdpOperBandwidth The value of sdpOperBandwidth indicates the operational
Bandwidth in kilo-bits per seconds (Kbps) available for
this SDP. The value sdpOperBandwidth is determined by the
sum of th… | column | kilo-bits per second SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.40 |
| sdpAvailableBandwidth The value of sdpAvailableBandwidth indicates the Bandwidth
that is still free for booking by the SDP bindings on the
SDP. | column | kilo-bits per second SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.41 |
| sdpMaxBookableBandwidth The value of sdpMaxBookableBandwidth indicates the max
Bandwidth that the SDP has for booking by the SDP
bindings. The value of sdpMaxBookableBandwidth is
calculated as follow:
… | column | kilo-bits per second SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.42 |
| sdpBookedBandwidth The value of sdpBookedBandwidth indicates the
SDP Bandwidth that has been booked by the SDP
bindings. | column | kilo-bits per second SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.43 |
| sdpCreationOrigin The value of sdpCreationOrigin indicates the protocol or
mechanism which created this SDP. | column | TN-SERV-MIBL2RouteOrigin | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.44 |
| sdpEnforceDiffServLspFc The value of sdpEnforceDiffServLspFc specifies
whether service manager must validate with RSVP the
support of the FC by the LSP.
By default, the SDP uses the direct… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.45 |
| sdpMixedLspModeEnabled The value of sdpMixedLspModeEnabled specifies whether
mixed mode LSPs is enabled on this SDP. Setting the
value to 'true' allows LDP to be enabled and LSPs to
be configured at th… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.46 |
| sdpLspRevertTime The value of sdpLspRevertTime specifies the time to wait
before reverting back from LDP to the configured LSPs,
after having failed over to LDP.
When the value is -… | column | seconds Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.47 |
| sdpLspRevertTimeCountDown The value of sdpLspRevertTimeCountDown indicated the timer
countdown before reverting back from LDP on this SDP.
The timer countdown begins after the first configured LSP
becomes … | column | seconds Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.48 |
| sdpLdpLspId The value of sdpLdpLspId indicates the Id for the LDP
LSP if sdpLdpEnabled is set to 'true' and there is a
valid LDP route to the sdpFarEndIpAddress or
sdpFarEndNodeId. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.49 |
| sdpLspList When the SDP delivery specified by sdpDelivery
is 'mpls', this object specifies the list of
LSPs used to reach the far-end ESR device.
All the LSPs in this list must terminate at … | column | TN-SERV-MIBLspIdList | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.5 |
| sdpLdpActive obsolete The value of sdpLdpActive indicates whether LDP is active
for the current SDP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.50 |
| sdpEgressIfsNetDomainConsistent The value of sdpEgressIfsNetDomainConsistent indicates whether all
the egress network interfaces that can carry traffic on this SDP are
associated with the network-domain configur… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.52 |
| sdpBgpTunnelEnabled The value of sdpBgpTunnelEnabled specifies whether
the transport tunnel is BGP as opposed to LDP or
RSVP signalled LSPs.
This value cannot be set to 'true' if sdpLd… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.53 |
| sdpBgpTunnelLspId The value of sdpBgpTunnelLspId indicates the Id for the
BGP Tunnel LSP if sdpBgpTunnelEnabled is set to 'true'
and there is a valid LDP route to the sdpFarEndIpAddress. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.54 |
| sdpTunnelFarEndIpAddress The value of sdpTunnelFarEndIpAddress specifies the
IP address of the remote end of the tranport tunnel for
this SDP.
The value can only be changed while the admin … | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.55 |
| sdpActiveLspType The value of sdpActiveLspType indicates the type of LSP
that is currently active on this SDP.
For sdpDelivery 'gre', the value is always
'not-applicable'.
… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.56 |
| sdpBindingPort The value of sdpBindingPort specifies the port id for
the binding on this SDP.
The value of sdpPwPortOperStatus will be set to 'down' of
all the related SDP pseudo-… | column | TN-TC-MIBTmnxPortID | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.57 |
| sdpFarEndNodeId The value of sdpFarEndNodeId specifies the node identifier
of the far-end for this sdp.
The value of this object must be set to a non-default value
when the sdpDeli… | column | TN-TC-MIBTmnxMplsTpNodeID | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.58 |
| sdpFarEndGlobalId The value of sdpFarEndGlobalId specifies the global
identifier of the far-end for this sdp. | column | TN-TC-MIBTmnxMplsTpGlobalID | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.59 |
| sdpDescription Generic information about this SDP. | column | TN-TC-MIBServObjDesc | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.6 |
| sdpLabelSignaling This object specifies the signaling protocol
used to obtain the ingress and egress labels
used in frames transmitted and received on
this SDP. When the value of this object is
'no… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.7 |
| sdpAdminStatus The desired state of this SDP. | column | TN-TC-MIBServiceAdminStatus | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.8 |
| sdpOperStatus The operating state of this SDP. The value
'notAlive' is valid only when keep-alive is
enabled, and it means that the keep-alive
operating status is not alive. The value
'notReady… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.4.3.1.9 |