tmnxOspfSpfSecondWait
TIMETRA-OSPF-NG-MIB ·
.1.3.6.1.4.1.6527.3.1.2.36.2.1.32
Object
column
r/w
milliseconds Unsigned32
The value of tmnxOspfSpfSecondWait defines the hold time between the
first and second SPF calculation. Subsequent SPF runs will occur at
exponentially increasing intervals of the tmnxOspfSpfSecondWait value
i.e., if tmnxOspfSpfSecondWait is 1000, then the next SPF triggered by
an event during this interval will run after 2000 msec, and the
subsequent one at 4000 msec, etc. until it is capped off at
tmnxOspfSpfMaxWait value. If this is configured as zero, there will be
no exponential backoff.
The SPF interval will stay at tmnxOspfSpfMaxWait value until there are
no more SPF runs scheduled in that interval. After a full interval
without any SPF runs, the SPF interval will drop back to
tmnxOspfSpfInitialWait.
Context
- MIB
- TIMETRA-OSPF-NG-MIB
- OID
.1.3.6.1.4.1.6527.3.1.2.36.2.1.32- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- tmnxOspfGeneralEntry
- Table
- tmnxOspfGeneralTable
- Siblings
- 63
Syntax
milliseconds Unsigned32
Values & Constraints
Object Constraints
range: 10-100000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tmnxOspfVersion The value of tmnxOspfVersion specifies the version number of OSPF
supported by this OSPF instance. The version number of OSPF for
IPv6 is 3. | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.36.2.1.1 |
| tmnxOspfMulticastExtensions The value of tmnxOspfMulticastExtensions specifies a Bit Mask
indicating whether the router is forwarding IPv6 multicast datagrams
based on the algorithms defined in the Multicast… | column | Bits | .1.3.6.1.4.1.6527.3.1.2.36.2.1.10 |
| tmnxOspfExitOverflowInterval The value of tmnxOspfExitOverflowInterval specifies the number of
seconds that, after entering Overflow State, a router will attempt
to leave Overflow State. This allows the route… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.11 |
| tmnxOspfDemandExtensions The value of tmnxOspfDemandExtensions specifies the router's support
for demand routing. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.12 |
| tmnxOspfReferenceBandwidth The value of tmnxOspfReferenceBandwidth specifies default
metrics to any OSPF interface. The cost metric is calculated
by dividing the value of tmnxOspfReferenceBandwidth by the … | column | 1000 bits per second Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.13 |
| tmnxOspfStrictLsaChecking The value of tmnxOspfStrictLsaChecking specifies whether or not to
perform strict LSA checking during OSPF graceful restart. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.14 |
| tmnxOspfRestartSupport The value of tmnxOspfRestartSupport specifies the router's support
for OSPF graceful restart. Options include: no restart support,
only planned restarts or both planned and unpla… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.36.2.1.15 |
| tmnxOspfRestartInterval The value of tmnxOspfRestartInterval specifies the configured OSPF
graceful restart timeout interval. | column | seconds TmnxOspfUpToRefreshIntervalTc | .1.3.6.1.4.1.6527.3.1.2.36.2.1.16 |
| tmnxOspfPreference The value of tmnxOspfPreference specifies the route preference for
OSPF internal routes. | column | TmnxOspfPreference | .1.3.6.1.4.1.6527.3.1.2.36.2.1.17 |
| tmnxOspfExternalPreference The value of tmnxOspfExternalPreference specifies the route preference
for OSPF external routes. | column | TmnxOspfPreference | .1.3.6.1.4.1.6527.3.1.2.36.2.1.18 |
| tmnxOspfExportPolicy1 The value of tmnxOspfExportPolicy1 specifies the name of the 1st
Export policy to be used for determining which routes are exported
from the routing table to OSPF. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.19 |
| tmnxOspfInstance The value of tmnxOspfInstance is a unique integer that identifies a
specific instance of a version of the OSPF protocol running in the
router instance specified by the vRtrID inde… | column | TIMETRA-TC-MIBTmnxOspfInstance | .1.3.6.1.4.1.6527.3.1.2.36.2.1.2 |
| tmnxOspfExportPolicy2 The value of tmnxOspfExportPolicy2 specifies the name of the 2nd
Export policy to be used for determining which routes are exported
from the routing table to OSPF. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.20 |
| tmnxOspfExportPolicy3 The value of tmnxOspfExportPolicy3 specifies the name of the 3rd
Export policy to be used for determining which routes are exported
from the routing table to OSPF. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.21 |
| tmnxOspfExportPolicy4 The value of tmnxOspfExportPolicy4 specifies the name of the 4rd
Export policy to be used for determining which routes are exported
from the routing table to OSPF. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.22 |
| tmnxOspfExportPolicy5 The value of tmnxOspfExportPolicy5 specifies the name of the 5th
Export policy to be used for determining which routes are exported
from the routing table to OSPF. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.23 |
| tmnxOspfManualSpfTrigger The value of tmnxOspfManualSpfTrigger specifies a manual Dijkstra SPF
calculation trigger.
When tmnxOspfManualSpfTrigger is set to 'runTotalSpf' a normal
Dijkstra S… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.36.2.1.24 |
| tmnxOspfOverloadAdmState The value of tmnxOspfOverloadAdmState specifies a command used to
manually make the system go in or out of overload state. Whenever this
value is set, tmnxOspfOverloadInterval is … | column | OSPF-MIBStatus | .1.3.6.1.4.1.6527.3.1.2.36.2.1.25 |
| tmnxOspfOverloadInterval The value of tmnxOspfOverloadInterval specifies how long (in seconds)
OSPF should remain in overload state. This is reset to default when
tmnxOspfOverloadAdmState is modified. The… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.26 |
| tmnxOspfBootOverloadAdmState The value of tmnxOspfBootOverloadAdmState specifies the desired
overload state that should be applied after boot Whenever this value
is set, tmnxOspfBootOverloadInterval is reset … | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.36.2.1.27 |
| tmnxOspfBootOverloadInterval The value of tmnxOspfBootOverloadInterval specifies the configured
value for OSPF for which it should remain in overload state on
boot-up. This is reset to default when tmnxOspfBo… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.28 |
| tmnxOspfOverloadStubs The value of tmnxOspfOverloadStubs specifies if the OSPF stub networks
should be advertised with a maximum metric value when the system goes
into overload state for any reason. If… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.29 |
| tmnxOspfSpfMaxWait The value of tmnxOspfSpfMaxWait defines the maximum interval between
two consecutive full SPF calculations. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.30 |
| tmnxOspfSpfInitialWait The value of tmnxOspfSpfInitialWait defines the hold down time before
a full SPF calculation delay after a topology change. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.31 |
| tmnxOspfLsaGenMaxWait The value of tmnxOspfLsaGenMaxWait defines the maximum interval
between two consecutive updates of a self generated LSA due to any
event. This is a way to manipulate the 'MinLSInt… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.33 |
| tmnxOspfLsaGenInitialWait The value of tmnxOspfLsaGenInitialWait defines the initial LSA
generation delay after an event that causes the LSA generation or
update. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.34 |
| tmnxOspfLsaGenSecondWait The value of tmnxOspfLsaGenSecondWait defines the hold time between
the first and second LSA generation.
Subsequent updates of that LSA will occur at exponentially … | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.35 |
| tmnxOspfLsaArrivalWait The value of tmnxOspfLsaArrivalWait defines the minimum interval
between two consecutive updates of an LSA received from any neighbor.
Any LSA update received before that is disca… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.36 |
| tmnxOspfTESupport The value of tmnxOspfTESupport specifies whether or not TEs
are supported by this instance of OSPF. When it has a value
of 'true', TEs are supported. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.37 |
| tmnxOspfUnicastImport The value of tmnxOspfUnicastImport specifies whether OSPF protocol
will submit routes into the unicast Route Table Manage(RTM).
When tmnxOspfUnicastImport has a val… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.38 |
| tmnxOspfMulticastImport The value of tmnxOspfMulticastImport specifies whether OSPF protocol
will submit routes into the multicast Reverse Path Forwarding(RPF)
Route Table Manage(RTM).
Whe… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.39 |
| tmnxOspfGeneralLastChanged The value of tmnxOspfGeneralLastChanged indicates the sysUpTime when a
configurable object in this row was last modified. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.6527.3.1.2.36.2.1.4 |
| tmnxOspfGREnable The value of tmnxOspfGREnable specifies whether the graceful restart
is enabled or disabled for this instance of OSPF on the router.
When tmnxOspfGREnable has a val… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.40 |
| tmnxOspfGRHelperMode The value of tmnxOspfGRHelperMode specifies whether the graceful
restart helper mode is enabled or disabled for this instance of OSPF
on the router. tmnxOspfGRHelperMode is valid … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.41 |
| tmnxOspfRowStatus The tmnxOspfRowStatus variable is used for creation and deletion of
tmnxOspfGeneralTable row entries. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.6527.3.1.2.36.2.1.42 |
| tmnxOspfAsbrDomainId The value of tmnxOspfAsbrDomainId specifies the domain-id associated
with this instance of OSPF on the router.
If no value is specified for tmnxOspfAsbrDomainId, it… | column | Integer32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.43 |
| tmnxOspfIgnoreDNBit The value of tmnxOspfIgnoreDNBit specifies whether to ignore the DN
bit for OSPF LSA packets for this instance of OSPF on the router.
When tmnxOspfIgnoreDNBit has a… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.44 |
| tmnxOspfSuppressDNBit The value of tmnxOspfSuppressDNBit specifies whether to suppress the
setting of the DN bit for OSPF LSA packets generated by this instance
of OSPF on the router.
Wh… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.45 |
| tmnxOspfLdpSyncAdminState The value of tmnxOspfLdpSyncAdminState specifies whether the IGP-LDP
synchronization feature is enabled or disabled on all interfaces
participating in the OSPF routing protocol.
… | column | OSPF-MIBStatus | .1.3.6.1.4.1.6527.3.1.2.36.2.1.46 |
| tmnxOspfVpnDomainType The value of tmnxOspfVpnDomainType specifies type of the extended
community attribute exchanged using BGP to carry the OSPF VPN Domain
ID. This object applies to VPRN instances of… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.36.2.1.47 |
| tmnxOspfVpnDomainId The value of tmnxOspfVpnDomainId specifies the OSPF VPN Domain. This
is exchanged using BGP in the extended community attribute associated
with a prefix. This object applies to VP… | column | OctetString | .1.3.6.1.4.1.6527.3.1.2.36.2.1.48 |
| tmnxOspfVpnTag The value of tmnxOspfVpnTag specifies the route tag for an OSPF VPN on
a PE router. This field is set in the tag field of the OSPF external
LSAs generated by the PE. This is mainl… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.49 |
| tmnxOspfRouterId The value of tmnxOspfRouterId specifies a 32-bit integer uniquely
identifying the router in the Autonomous System. By convention
to ensure uniqueness, this may default to the val… | column | TmnxOspfRouterIdTc | .1.3.6.1.4.1.6527.3.1.2.36.2.1.5 |
| tmnxOspfSuperBackBone The value of tmnxOspfSuperBackBone specifies whether CE-PE
functionality is required or not. tmnxOspfSuperBackBone indicates the
type of the LSA generated as a result of routes re… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.50 |
| tmnxOspfLdpOverRsvp The value of tmnxOspfLdpOverRsvp specifies whether LDP-over-RSVP
feature is enabled or disabled for a specific OSPF instance.
When tmnxOspfLdpOverRsvp is enabled, O… | column | TIMETRA-TC-MIBTmnxEnabledDisabled | .1.3.6.1.4.1.6527.3.1.2.36.2.1.51 |
| tmnxOspfExportLimit The value of tmnxOspfExportLimit specifies the maximum number of
routes or prefixes that can be exported into OSPF or OSPF3 from the
route table.
A value of 0 indic… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.52 |
| tmnxOspfExportLimitLogPercent The value of tmnxOspfExportLimitLogPercent specifies the percentage of
the export-limit, at which a warning log message and SNMP notification
would be sent. This would only be a w… | column | percent Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.53 |
| tmnxOspfRsvpShortcut obsolete The value of tmnxOspfRsvpShortcut specifies whether RSVP-TE shortcut
for resolving IGP routes has been enabled or disabled for OSPF.
When the value of tmnxOspfRsvpS… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.54 |
| tmnxOspfAdvertiseTunnelLink The value of tmnxOspfAdvertiseTunnelLink specifies whether
advertisement of LSP shortcuts into IGP has been enabled or disabled
for OSPF.
When the value of tmnxOspf… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.55 |
| tmnxOspfImportPolicy1 The value of tmnxOspfImportPolicy1 specifies the name of the 1st
import policy to be used for determining which routes are imported
from OSPF to the routing table. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.56 |
| tmnxOspfImportPolicy2 The value of tmnxOspfImportPolicy2 specifies the name of the 2nd
import policy to be used for determining which routes are imported
from OSPF to the routing table. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.57 |
| tmnxOspfImportPolicy3 The value of tmnxOspfImportPolicy3 specifies the name of the 3rd
import policy to be used for determining which routes are imported
from OSPF to the routing table. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.58 |
| tmnxOspfImportPolicy4 The value of tmnxOspfImportPolicy4 specifies the name of the 4rd
import policy to be used for determining which routes are imported
from OSPF to the routing table. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.59 |
| tmnxOspfAdminState The value of tmnxOspfAdminState specifies the desired administrative
status of this instance of OSPF in the router. The value 'enabled'
activates this instance of the OSPF protoco… | column | OSPF-MIBStatus | .1.3.6.1.4.1.6527.3.1.2.36.2.1.6 |
| tmnxOspfImportPolicy5 The value of tmnxOspfImportPolicy5 specifies the name of the 5thimport
policy to be used for determining which routes are imported from OSPF
to the routing table. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.36.2.1.60 |
| tmnxOspfLoopfreeAlternate The value of tmnxOspfLoopfreeAlternate specifies whether to enable or
disable IP fast reroute capability for OSPF.
When the value of tmnxOspfLoopfreeAlternate is se… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.61 |
| tmnxOspfLsaAccumulate The value of tmnxOspfLsaAccumulate defines the accumulation delay for
multiple LSAs, so OSPF messages can be sent as efficiently as
possible.
Shorting this delay ca… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.62 |
| tmnxOspfRedistDelay The value of tmnxOspfRedistDelay defines the internal OSPF hold down
timer for external routes being redistributed into OSPF.
Shorting this delay can speed up the a… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.63 |
| tmnxOspfIncrSpfWait The value of tmnxOspfIncrSpfWait defines the internal OSPF delay
before an incremental SPF calculation is performed. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.64 |
| tmnxOspfOverloadInclExt2 The value of tmnxOspfOverloadInclExt2 specifies if the OSPF external
prefixes with metric-type 2, should be advertised with a maximum
metric value when the system goes into overlo… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.65 |
| tmnxOspfASBdrRtrStatus The value of tmnxOspfASBdrRtrStatus specifies whether this router is
configured as an Autonomous System border router. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.7 |
| tmnxOspfRFC1583Compatibility The value of tmnxOspfRFC1583Compatibility indicates the metrics used
to choose among multiple AS-external-LSAs. When
tmnxOspfRFC1583Compatibility is set to 'true', only cost will … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.36.2.1.8 |
| tmnxOspfExtLsdbLimit The value of tmnxOspfExtLsdbLimit specifies the maximum number of
non-default AS-external-LSAs entries that can be stored in the
link-state database. If the value is -1, then ther… | column | Integer32 | .1.3.6.1.4.1.6527.3.1.2.36.2.1.9 |