sleMplsTpLpsCfgInfoProtectionScheme
SLE-MPLS-TP-LPS-MIB ·
.1.3.6.1.4.1.6296.101.16.18.1.1.1.4
Object
column
Enumeration
The object represents the operational scheme of
protection switching group. The protection scheme may
either be unidirectional or bidirectional.
bidirectional
In bidirectional protection scheme, both the directions
will be switched simultaneously even if the fault
applies to only one direction of the path.
unidirectional
In unidirectional protection scheme protection switching
will be performed independently for each direction of a
bidirectional transport path
This object may not be modified if the associated
sleMplsTpLpsCfgRowStatus object is equal to active(1).
Context
- MIB
- SLE-MPLS-TP-LPS-MIB
- OID
.1.3.6.1.4.1.6296.101.16.18.1.1.1.4- Type
- column
- Access
- readonly
- Status
- current
- Parent
- sleMplsTpLpsCfgInfoEntry
- Table
- sleMplsTpLpsCfgInfoTable
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | bidirectional |
2 | unidirectional |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sleMplsTpLpsCfgInfoGroupIndex Index for the conceptual row identifying a protection group. | column | Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.1 |
| sleMplsTpLpsCfgInfoLockOut this is object is used for preventing the swith traffic by the protection path. | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.10 |
| sleMplsTpLpsCfgInfoHoldOffTimer this object used for show the hold off timer. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.11 |
| sleMplsTpLpsCfgInfoActivePath This object say which path is Active . | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.12 |
| sleMplsTpLpsCfgInfoOperationState this object says Operational Status of LPS. The LPS is between PE to PE. | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.13 |
| sleMplsTpLpsCfgInfoEventStatus This is object says EVENT Status of LPS protection . | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.14 |
| sleMplsTpLpsCfgInfoGroupName Textual name represents the sleMplsTp tp protection group.
Each Protection Group is identified by a unique
protection group name. | column | OctetString | .1.3.6.1.4.1.6296.101.16.18.1.1.1.2 |
| sleMplsTpLpsCfgInfoMode The architectural mode of the Protection group. This can
either be 1+1, 1:1, 1:n.
1+1
In the 1+1 protection scheme, a fully dedicated
protection enti… | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.3 |
| sleMplsTpLpsCfgInfoRevertive This object represents the reversion mode of the Linear
Protection Switching group. The reversion mode of
protection mechanism may be either revertive or
non-revertive.
… | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.5 |
| sleMplsTpLpsCfgInfoWtr This object hold the Wait To Restore timer value in
seconds.
The WTR timer is used to delay reversion of PSC state
to Normal state when recovering from a failure
condition on the … | column | seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.6 |
| sleMplsTpLpsCfgInfoContinualTxInterval The Continual Tx Time in Seconds. Represents the time
interval to send the continual LPS packet to the other
end based on the current state. | column | seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.7 |
| sleMplsTpLpsCfgInfoRapidTxInterval The Rapid Tx interval in micro-Seconds. Represents the time
interval to send the LPS packet to the other end, when
there is a change in state of Linear Protection domain due
to lo… | column | micro-seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.8 |
| sleMplsTpLpsCfgInfoSwitchOver this object used for switch the traffic to the back up path. | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.9 |