sleMplsTpLpsCfgInfoMode
SLE-MPLS-TP-LPS-MIB ·
.1.3.6.1.4.1.6296.101.16.18.1.1.1.3
Object
column
Enumeration
The architectural mode of the Protection group. This can
either be 1+1, 1:1, 1:n.
1+1
In the 1+1 protection scheme, a fully dedicated
protection entity is allocated. Data traffic is copied
and fed at the source to both the working and the
protection entities. The traffic on the working and the
protection entities is transmitted simultaneously to
the sink of the protection domain, where selection
between the working and protection entities is performed
1:1
In the 1:1 scheme, a protection path is allocated to
protect against a defect, failure, or a degradation in a
working path. In normal conditions, data traffic is
transmitted over the working entity, while the
protection entity functions in the idle state. If there
is a defect on the working entity or a specific
administrative request, traffic is switched to the
protection entity.
1:n
In case of 1:n linear protection, one protection entity
is allocated to protect n working entities. The protection
entity might not have sufficient resources to protect all the
working entities that may be affected by fault conditions at a
specific time. In this case, in order to guaranteed
protection, the protection entity should support enough
capacity and bandwidth to protect any of the n working
entities.
Context
- MIB
- SLE-MPLS-TP-LPS-MIB
- OID
.1.3.6.1.4.1.6296.101.16.18.1.1.1.3- Type
- column
- Access
- readonly
- Status
- current
- Parent
- sleMplsTpLpsCfgInfoEntry
- Table
- sleMplsTpLpsCfgInfoTable
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | onePlusOne |
2 | oneColonOne |
3 | oneColonN |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sleMplsTpLpsCfgInfoGroupIndex Index for the conceptual row identifying a protection group. | column | Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.1 |
| sleMplsTpLpsCfgInfoLockOut this is object is used for preventing the swith traffic by the protection path. | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.10 |
| sleMplsTpLpsCfgInfoHoldOffTimer this object used for show the hold off timer. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.11 |
| sleMplsTpLpsCfgInfoActivePath This object say which path is Active . | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.12 |
| sleMplsTpLpsCfgInfoOperationState this object says Operational Status of LPS. The LPS is between PE to PE. | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.13 |
| sleMplsTpLpsCfgInfoEventStatus This is object says EVENT Status of LPS protection . | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.14 |
| sleMplsTpLpsCfgInfoGroupName Textual name represents the sleMplsTp tp protection group.
Each Protection Group is identified by a unique
protection group name. | column | OctetString | .1.3.6.1.4.1.6296.101.16.18.1.1.1.2 |
| sleMplsTpLpsCfgInfoProtectionScheme The object represents the operational scheme of
protection switching group. The protection scheme may
either be unidirectional or bidirectional.
bidirectional
In bi… | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.4 |
| sleMplsTpLpsCfgInfoRevertive This object represents the reversion mode of the Linear
Protection Switching group. The reversion mode of
protection mechanism may be either revertive or
non-revertive.
… | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.5 |
| sleMplsTpLpsCfgInfoWtr This object hold the Wait To Restore timer value in
seconds.
The WTR timer is used to delay reversion of PSC state
to Normal state when recovering from a failure
condition on the … | column | seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.6 |
| sleMplsTpLpsCfgInfoContinualTxInterval The Continual Tx Time in Seconds. Represents the time
interval to send the continual LPS packet to the other
end based on the current state. | column | seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.7 |
| sleMplsTpLpsCfgInfoRapidTxInterval The Rapid Tx interval in micro-Seconds. Represents the time
interval to send the LPS packet to the other end, when
there is a change in state of Linear Protection domain due
to lo… | column | micro-seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.1.1.8 |
| sleMplsTpLpsCfgInfoSwitchOver this object used for switch the traffic to the back up path. | column | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.1.1.9 |