sleMplsTpLpsCfgControlRequest

SLE-MPLS-TP-LPS-MIB · .1.3.6.1.4.1.6296.101.16.18.1.2.1
MIB view Table view

Object

scalar r/w Enumeration 
the configuration commands, and user can configure functions 
via setting this entry as proper value.

Context

MIB
SLE-MPLS-TP-LPS-MIB
OID
.1.3.6.1.4.1.6296.101.16.18.1.2.1
Type
scalar
Access
readwrite
Status
current
Parent
sleMplsTpLpsCfgControl
Siblings
14

Syntax

Enumeration

Values & Constraints

Enumerated Values
1createSleMplsTpLpsCfgEntry
2deleteSleMplsTpLpsCfgEntry
3setSleMplsTpLpsCfgControProtectionScheme
4unsetSleMplsTpLpsCfgControProtectionScheme
5setSleMplsLpsTpCfgControlRevertive
6setSleMplsLpsTpCfgControlWaitToRestoreset
7unsetSleMplsTpLpsCfgControlWaitToRestoreset
8setSleMplsLpsTpCfgControlContinualTxInterval
9unsetSleMplsTpLpsCfgControlContinualTxInterval
10setSleMplsLpsTpCfgControlRapidTxInterval
11unsetSleMplsTpLpsCfgControlRapidTxInterval
12setSleMplsLpsTpCfgControlSwitchover
13unsetSleMplsTpLpsCfgControlSwitchover
14setSleMplsTpLpsCfgControlLockOut
15unsetSleMplsTpLpsTpCfgControlLockOut
16setSleMplsTpLpsCfgControlHoldOffTimer
17unSetSleMplsTpLpsCfgControlHoldOffTimer

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
sleMplsTpLpsCfgControlWtr
This object hold the Wait To Restore timer value in seconds. The WTR timer is used to delay reversion of PSC state to Normal state when recovering from a failure condition on the …
scalarseconds Unsigned32.1.3.6.1.4.1.6296.101.16.18.1.2.10
sleMplsTpLpsCfgControlContinualTxInterval
The Continual Tx Time in Seconds. Represents the time interval to send the continual LPS packet to the other end based on the current state.
scalarseconds Unsigned32.1.3.6.1.4.1.6296.101.16.18.1.2.11
sleMplsTpLpsCfgControlRapidTxInterval
The Rapid Tx interval in micro-Seconds. Represents the time interval to send the LPS packet to the other end, when there is a change in state of Linear Protection domain due to lo…
scalarmicro-seconds Unsigned32.1.3.6.1.4.1.6296.101.16.18.1.2.12
sleMplsTpLpsCfgControlswitchOver
this object used for switch the traffic to the back up path.
scalarEnumeration.1.3.6.1.4.1.6296.101.16.18.1.2.13
sleMplsTpLpsCfgControlLockOut
this is object is used for preventing the swith traffic by the protection path.
scalarEnumeration.1.3.6.1.4.1.6296.101.16.18.1.2.14
sleMplsTpLpsCfgControlHoldOffTimer
This object is used to set the holdofftimer
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.6296.101.16.18.1.2.15
sleMplsTpLpsCfgControlStatus
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
scalarSLE-TC-MIBSleControlStatusType.1.3.6.1.4.1.6296.101.16.18.1.2.2
sleMplsTpLpsCfgControlTimer
the wait-time until setRequest end. In case of short-time command, this value is 0
scalarSNMPv2-SMIGauge32.1.3.6.1.4.1.6296.101.16.18.1.2.3
sleMplsTpLpsCfgControlTimeStamp
the time stamp of the last command. (don.t care)
scalarSNMPv2-SMITimeTicks.1.3.6.1.4.1.6296.101.16.18.1.2.4
sleMplsTpLpsCfgControlReqResult
Result of the last command.
scalarSLE-TC-MIBSleControlRequestResultType.1.3.6.1.4.1.6296.101.16.18.1.2.5
sleMplsTpLpsCfgControlGroupName
Textual name represents the sleMplsTp tp protection group. Each Protection Group is identified by a unique protection group name.
scalarOctetString.1.3.6.1.4.1.6296.101.16.18.1.2.6
sleMplsTpLpsCfgControlMode
The architectural mode of the Protection group. This can either be 1+1, 1:1, 1:n. 1+1 In the 1+1 protection scheme, a fully dedicated protection entity is al…
scalarEnumeration.1.3.6.1.4.1.6296.101.16.18.1.2.7
sleMplsTpLpsCfgControlProtectionScheme
The object represents the operational scheme of protection switching group. The protection scheme may either be unidirectional or bidirectional. bidirectional In bidire…
scalarEnumeration.1.3.6.1.4.1.6296.101.16.18.1.2.8
sleMplsTpLpsCfgControlRevertive
This object represents the reversion mode of the Linear Protection Switching group. The reversion mode of protection mechanism may be either revertive or non-revertive. …
scalarEnumeration.1.3.6.1.4.1.6296.101.16.18.1.2.9