sleMplsTpLpsCfgControlRapidTxInterval
SLE-MPLS-TP-LPS-MIB ·
.1.3.6.1.4.1.6296.101.16.18.1.2.12
Object
scalar
r/w
micro-seconds Unsigned32
The Rapid Tx interval in micro-Seconds. Represents the time interval to send the LPS packet to the other end, when there is a change in state of Linear Protection domain due to local input. The default value is 3.3 milli-seconds which is 3300 micro-seconds
Context
- MIB
- SLE-MPLS-TP-LPS-MIB
- OID
.1.3.6.1.4.1.6296.101.16.18.1.2.12- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- micro-seconds
- Parent
- sleMplsTpLpsCfgControl
- Siblings
- 14
Syntax
micro-seconds Unsigned32
Values & Constraints
Object Constraints
range: 1000-1000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sleMplsTpLpsCfgControlRequest the configuration commands, and user can configure functions
via setting this entry as proper value. | scalar | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.2.1 |
| sleMplsTpLpsCfgControlWtr This object hold the Wait To Restore timer value in
seconds.
The WTR timer is used to delay reversion of PSC state
to Normal state when recovering from a failure
condition on the … | scalar | seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.2.10 |
| sleMplsTpLpsCfgControlContinualTxInterval The Continual Tx Time in Seconds. Represents the time
interval to send the continual LPS packet to the other
end based on the current state. | scalar | seconds Unsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.2.11 |
| sleMplsTpLpsCfgControlswitchOver this object used for switch the traffic to the back up path. | scalar | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.2.13 |
| sleMplsTpLpsCfgControlLockOut this is object is used for preventing the swith traffic by the protection path. | scalar | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.2.14 |
| sleMplsTpLpsCfgControlHoldOffTimer This object is used to set the holdofftimer | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6296.101.16.18.1.2.15 |
| sleMplsTpLpsCfgControlStatus status of user command. User have to check this value as
.busy. or .idle. before do setRequest. | scalar | SLE-TC-MIBSleControlStatusType | .1.3.6.1.4.1.6296.101.16.18.1.2.2 |
| sleMplsTpLpsCfgControlTimer the wait-time until setRequest end. In case of short-time command, this value is 0 | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6296.101.16.18.1.2.3 |
| sleMplsTpLpsCfgControlTimeStamp the time stamp of the last command. (don.t care) | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.6296.101.16.18.1.2.4 |
| sleMplsTpLpsCfgControlReqResult Result of the last command. | scalar | SLE-TC-MIBSleControlRequestResultType | .1.3.6.1.4.1.6296.101.16.18.1.2.5 |
| sleMplsTpLpsCfgControlGroupName Textual name represents the sleMplsTp tp protection group.
Each Protection Group is identified by a unique
protection group name. | scalar | OctetString | .1.3.6.1.4.1.6296.101.16.18.1.2.6 |
| sleMplsTpLpsCfgControlMode The architectural mode of the Protection group. This can
either be 1+1, 1:1, 1:n.
1+1
In the 1+1 protection scheme, a fully dedicated
protection entity is al… | scalar | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.2.7 |
| sleMplsTpLpsCfgControlProtectionScheme The object represents the operational scheme of
protection switching group. The protection scheme may
either be unidirectional or bidirectional.
bidirectional
In bidire… | scalar | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.2.8 |
| sleMplsTpLpsCfgControlRevertive This object represents the reversion mode of the Linear
Protection Switching group. The reversion mode of
protection mechanism may be either revertive or
non-revertive.
… | scalar | Enumeration | .1.3.6.1.4.1.6296.101.16.18.1.2.9 |