slmSysResetPm

SL-MAIN-MIB · .1.3.6.1.4.1.4515.1.3.1.23
MIB view Table view

Object

scalar r/w SNMPv2-SMIInteger32 
Writing 1 to this object reset the system PM counters.

Context

MIB
SL-MAIN-MIB
OID
.1.3.6.1.4.1.4515.1.3.1.23
Type
scalar
Access
readwrite
Status
current
Parent
slmSys
Siblings
53

Syntax

SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
slmSysGatewayAddr
Gateway node IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.1
slmSysPmStartOfDay
The time of day that marks the beginning of each 1-day interval used in the performance monitoring parameters for all interfaces in the NE. This time is on an hour boundary.
scalarInteger32.1.3.6.1.4.1.4515.1.3.1.10
slmSysActiveSwVersion
Determines the active software version. This is the version that will be loaded by rebooted cards. It is not legal to set this object to the id of an illegal system software versi…
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.11
slmSwRevTable
This table keeps the information about the system software revisions.
table-.1.3.6.1.4.1.4515.1.3.1.12
slmConfigSysUptime
The number of timer ticks at the last configuration command.
scalarSNMPv2-SMITimeTicks.1.3.6.1.4.1.4515.1.3.1.13
slmConfigSysSignalType
This variable identifies whether a SONET or a SDH signal is used across this node. This value is configured by the NMS.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.14
slmRebootDelay
The number of seconds to wait before reboot. When this number equal to 0 the reboot should occur immediately. After the reboot command is initiated, the value of this object decre…
scalarInteger32.1.3.6.1.4.1.4515.1.3.1.16
slmVcatDelay
The value of the VCAT delay as was read from the SEEP.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.17
slmTid
The SL TL1 name.
scalarOctetString.1.3.6.1.4.1.4515.1.3.1.18
slmPsuNumber
Let the NMS to configure the number of PSU in the system. If this number mismatch the reality, a mismatch alarm is declared.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.19
slmSysSubnetMask
Subnetwork Mask IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.2
slmOemType
This value tells the NMS the type of the OEM. This value is read from the SEEP.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.20
slmSysName
This value is the shadow of the sysName object.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.21
slmSysLocation
This value is the shadow of the sysLocation object.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.22
slmSysUplinkRate
This object is used to configure the rate of the Uplink. The configured rate applies to both Uplink ports.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.24
slmSysChassisId
This object is used to configure the chassis-id. Node with the same value are considered to be stacked.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.25
slmSysNetworkPrefix
This object is used to configure the Network Prefix. The prefix is used when the IP address of the node is assigned automatically. The automatic IP address of the node has the fo…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.26
slmSysLanIpAddr
Node LAN IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.27
slmSysLanSubnetAddr
Node LAN Subnet Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.28
slmPmAvailable
This value tells the NMS if the PM support is available. The value is taken from the SEEP and can not be changed.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4515.1.3.1.29
slmSysIpAddr
Node IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.3
slmPortsNumber
The number of ports in the system. The value is taken from the SEEP.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.30
slmEdfaNumber
The number of EDFA units in the system. The value is taken from the SEEP.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.31
slmMuxNumber
The number of MUX units in the system. The value is taken from the SEEP.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.32
slmOpticalSwitchExist
Should an Optical Switch unit exist in the system. The value is taken from the SEEP.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4515.1.3.1.33
slmReadCommunity
The SNMP read-only community. This object should be accessible only by the Admin users of the Web.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.34
slmWriteCommunity
The SNMP read-write community. This object should be accessible only by the Admin users of the Web.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.35
slmSysEffectiveSubnetMask
Effective Management subnetwork mask IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.36
slmSysEffectiveIpAddr
Effective Management IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.37
slmSysLanEffectiveIpAddr
Effective LAN IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.38
slmSysLanEffectiveSubnetAddr
Effective LAN subnetwork mask address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.39
slmSysAlmAct
Alarm Activation Time specified in Half-Seconds units. Alarm will be considered active only if it has been stable for that time.
scalarInteger32.1.3.6.1.4.1.4515.1.3.1.4
slmSysGatewayEffectiveIpAddr
Effective Gateway IP Address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4515.1.3.1.40
slmSysMode
System Mode configuration (this object applies to muxponder).
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.41
slmSysTrapFormat
The format of the sent trap: 1 - the full ifIndex is sent. 2 - only the port number part of the ifIndex is sent.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.42
slmSysTemperature
The temperature of the PL device in Celsius.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.43
slmNetworkMode
1 - means that the LAN is define on a different vlan than the MNG ports. 2 - means that the LAN is on the same vlan and the MNG ports
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.44
slm40GConf
g40(0) - No 40G ports (service ports 3..10 are disabled) g41(1) - Single 40G Port 1 (service ports 7,8,9,10 are disabled) g42(2) - Single 40G Port 2 (service ports 3,4,5,6 are dis…
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.45
slmRstpEnabled
Enable/Disable the RSTP protocol. Defalut value is TRUE.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4515.1.3.1.46
slmTopologyEnabled
Enable/Disable the topology discovery protocol. Defalut value is TRUE.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4515.1.3.1.47
slmAdminCommunity
The SNMP admin community. This object should be accessible only by the Admin users of the Web.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.48
slmTrapCommunity
The SNMP v1/v2c trap community. This object should be accessible only by the Admin users of the Web.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.49
slmSysAlmDeact
Alarm Clearance Time specified in Half-Seconds units. Alarm will be considered clear only if it has been stable for that time.
scalarInteger32.1.3.6.1.4.1.4515.1.3.1.5
slmSysSnmpVersion
The format of the sent trap: 3 - allow only SNMPv3 pdus. 4 - allow all pdus (coexistance mode).
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.50
slmSysEncryptionCapability
The encryption capability: 1 - No Encryption. 2 - Encryption Supported.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.51
slmSysMaxExpirationTime
The maximal GUI and CLI session expiration time in seconds.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.52
slmInbandMode
1 - L2 Inband: IP over Ethernet (default). 2 - L3 Inband: IP over PPP over Ethernet
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.53
slmPublicCommunity
The public community string. Default is public.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4515.1.3.1.54
slmSysLogMessageLevel
The level of logging messages. 0 - None 1 - Fatal 2 - Traps 3 - Detailed 4 - debug
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.4515.1.3.1.55
slmSysAdminStatus
Instruct the system to perform the boot according to the specified type.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.6
slmSysOperStatus
The operational system state.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.7
slmBoxSize
The box size as was configured in the SEEP.
scalarEnumeration.1.3.6.1.4.1.4515.1.3.1.8
slmSysCalendarTime
The system calendar time.
scalarSNMPv2-TCDateAndTime.1.3.6.1.4.1.4515.1.3.1.9