slmEdfaNumber
SL-MAIN-MIB ·
.1.3.6.1.4.1.4515.1.3.1.31
Object
scalar
SNMPv2-SMIInteger32
The number of EDFA units in the system. The value is taken from the SEEP.
Context
- MIB
- SL-MAIN-MIB
- OID
.1.3.6.1.4.1.4515.1.3.1.31- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- slmSys
- Siblings
- 53
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| slmSysGatewayAddr Gateway node IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.1 |
| slmSysPmStartOfDay The time of day that marks the beginning of each 1-day interval
used in the performance monitoring parameters for all interfaces
in the NE. This time is on an hour boundary. | scalar | Integer32 | .1.3.6.1.4.1.4515.1.3.1.10 |
| slmSysActiveSwVersion Determines the active software version. This is the version that will
be loaded by rebooted cards. It is not legal to set this object
to the id of an illegal system software versi… | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.11 |
| slmSwRevTable This table keeps the information about the system
software revisions. | table | - | .1.3.6.1.4.1.4515.1.3.1.12 |
| slmConfigSysUptime The number of timer ticks at the last configuration command. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.4515.1.3.1.13 |
| slmConfigSysSignalType This variable identifies whether a SONET
or a SDH signal is used across this node.
This value is configured by the NMS. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.14 |
| slmRebootDelay The number of seconds to wait before reboot.
When this number equal to 0 the reboot should occur immediately.
After the reboot command is initiated, the value of this object
decre… | scalar | Integer32 | .1.3.6.1.4.1.4515.1.3.1.16 |
| slmVcatDelay The value of the VCAT delay as was read from the SEEP. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.17 |
| slmTid The SL TL1 name. | scalar | OctetString | .1.3.6.1.4.1.4515.1.3.1.18 |
| slmPsuNumber Let the NMS to configure the number of PSU in the system.
If this number mismatch the reality, a mismatch alarm is declared. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.19 |
| slmSysSubnetMask Subnetwork Mask IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.2 |
| slmOemType This value tells the NMS the type of the OEM.
This value is read from the SEEP. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.20 |
| slmSysName This value is the shadow of the sysName object. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.21 |
| slmSysLocation This value is the shadow of the sysLocation object. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.22 |
| slmSysResetPm Writing 1 to this object reset the system PM counters. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.23 |
| slmSysUplinkRate This object is used to configure the rate of the Uplink.
The configured rate applies to both Uplink ports. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.24 |
| slmSysChassisId This object is used to configure the chassis-id.
Node with the same value are considered to be stacked. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.25 |
| slmSysNetworkPrefix This object is used to configure the Network Prefix.
The prefix is used when the IP address of the node is
assigned automatically.
The automatic IP address of the node has the fo… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.26 |
| slmSysLanIpAddr Node LAN IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.27 |
| slmSysLanSubnetAddr Node LAN Subnet Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.28 |
| slmPmAvailable This value tells the NMS if the PM support is available.
The value is taken from the SEEP and can not be changed. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.3.1.29 |
| slmSysIpAddr Node IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.3 |
| slmPortsNumber The number of ports in the system.
The value is taken from the SEEP. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.30 |
| slmMuxNumber The number of MUX units in the system.
The value is taken from the SEEP. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.32 |
| slmOpticalSwitchExist Should an Optical Switch unit exist in the system.
The value is taken from the SEEP. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.3.1.33 |
| slmReadCommunity The SNMP read-only community.
This object should be accessible only by the Admin users of the Web. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.34 |
| slmWriteCommunity The SNMP read-write community.
This object should be accessible only by the Admin users of the Web. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.35 |
| slmSysEffectiveSubnetMask Effective Management subnetwork mask IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.36 |
| slmSysEffectiveIpAddr Effective Management IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.37 |
| slmSysLanEffectiveIpAddr Effective LAN IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.38 |
| slmSysLanEffectiveSubnetAddr Effective LAN subnetwork mask address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.39 |
| slmSysAlmAct Alarm Activation Time specified in Half-Seconds units.
Alarm will be considered active only if it
has been stable for that time. | scalar | Integer32 | .1.3.6.1.4.1.4515.1.3.1.4 |
| slmSysGatewayEffectiveIpAddr Effective Gateway IP Address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4515.1.3.1.40 |
| slmSysMode System Mode configuration (this object applies to muxponder). | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.41 |
| slmSysTrapFormat The format of the sent trap:
1 - the full ifIndex is sent.
2 - only the port number part of the ifIndex is sent. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.42 |
| slmSysTemperature The temperature of the PL device in Celsius. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.43 |
| slmNetworkMode 1 - means that the LAN is define on a different vlan than the MNG ports.
2 - means that the LAN is on the same vlan and the MNG ports | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.44 |
| slm40GConf g40(0) - No 40G ports (service ports 3..10 are disabled)
g41(1) - Single 40G Port 1 (service ports 7,8,9,10 are disabled)
g42(2) - Single 40G Port 2 (service ports 3,4,5,6 are dis… | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.45 |
| slmRstpEnabled Enable/Disable the RSTP protocol.
Defalut value is TRUE. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.3.1.46 |
| slmTopologyEnabled Enable/Disable the topology discovery protocol.
Defalut value is TRUE. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.3.1.47 |
| slmAdminCommunity The SNMP admin community.
This object should be accessible only by the Admin users of the Web. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.48 |
| slmTrapCommunity The SNMP v1/v2c trap community.
This object should be accessible only by the Admin users of the Web. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.49 |
| slmSysAlmDeact Alarm Clearance Time specified in Half-Seconds units.
Alarm will be considered clear only if it
has been stable for that time. | scalar | Integer32 | .1.3.6.1.4.1.4515.1.3.1.5 |
| slmSysSnmpVersion The format of the sent trap:
3 - allow only SNMPv3 pdus.
4 - allow all pdus (coexistance mode). | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.50 |
| slmSysEncryptionCapability The encryption capability:
1 - No Encryption.
2 - Encryption Supported. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.51 |
| slmSysMaxExpirationTime The maximal GUI and CLI session expiration time in seconds. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.52 |
| slmInbandMode 1 - L2 Inband: IP over Ethernet (default).
2 - L3 Inband: IP over PPP over Ethernet | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.53 |
| slmPublicCommunity The public community string. Default is public. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.3.1.54 |
| slmSysLogMessageLevel The level of logging messages.
0 - None
1 - Fatal
2 - Traps
3 - Detailed
4 - debug | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.3.1.55 |
| slmSysAdminStatus Instruct the system to perform the boot
according to the specified type. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.6 |
| slmSysOperStatus The operational system state. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.7 |
| slmBoxSize The box size as was configured in the SEEP. | scalar | Enumeration | .1.3.6.1.4.1.4515.1.3.1.8 |
| slmSysCalendarTime The system calendar time. | scalar | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.4515.1.3.1.9 |