edfaPumpOperStatus
SL-EDFA-MIB ·
.1.3.6.1.4.1.4515.1.9.1.1.1.5
Object
column
Enumeration
The current operational state of the laser. If edfaPumpAdminStatus is down(2) then edfaPumpOperStatus should be down(2). If edfaPumpAdminStatus is changed to up(1) then edfaPumpOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should remain in the down(2) state if and only if there is a fault that prevents it from going to the up(1) state. The operational status is equal to restart(3) if the edfa pump is still in restart process.
Context
- MIB
- SL-EDFA-MIB
- OID
.1.3.6.1.4.1.4515.1.9.1.1.1.5- Type
- column
- Access
- readonly
- Status
- current
- Parent
- edfaConfigEntry
- Table
- edfaConfigTable
- Siblings
- 36
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | up |
2 | down |
3 | restart |
4 | unknown |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| edfaIfIndex The amplifier interface index. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4515.1.9.1.1.1.1 |
| edfaOperControlMode The current Edfa control mode. Initialy the Edfa
starts in APC mode. The AGC mode is used only when
selected manualy or after transient input power change. | column | Enumeration | .1.3.6.1.4.1.4515.1.9.1.1.1.10 |
| edfaAdminGain The required Edfa Gain value given in 0.1 dB units. This value
may be configured only when the edfa automatic mode is FALSE
and the edfa control mode is Agc. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.11 |
| edfaOperGain The actual Edfa Gain value given in 0.1 dB units.
Value range starts with 0.0 dbm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.12 |
| edfaAdminOutputPower The required Edfa output power value given in 0.1 dBm units.
The range starts with -30.0 dBm. This value
may be configured only when the edfa control mode is Apc.
The units in the… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.13 |
| edfaOperOutputPower The actual Edfa total output power value specified in 0.1 dBm units.
Valid valuse are in the range of 0.0 dBm upto +15.0 dBm.
The units in the case of RAMAN AMP are 0.1 mW. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.14 |
| edfaChannelsNumber The number of optical channels on this signal. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.15 |
| edfaTotalChannelsNumber The total number of optical channels on this fiber. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.16 |
| edfaEyeSafetyMode When in Eye-Safety mode the edfa reduces the laser
power budget down to safe level upon detection of an
output fiber cut. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.9.1.1.1.17 |
| edfaShutDownLipEnable EDFA shout-down on LIP (Loss of signal) -
enable/disable. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.9.1.1.1.18 |
| edfaAutoPowerUpLipEnable EDFA automatic power up (after signal returns) -
enable/disable. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.9.1.1.1.19 |
| edfaPumpTemp The pump temperture (in Kelvin). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.2 |
| edfaMaxGain The EDFA max gain is determined by the result of the VER command.
Legal values:
gainUnknown(1)
gain14dbm(2) - Booster/Inline, (-2)-14dBm output power, gain (-5)-22dB
gain17dbm(3)… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.20 |
| edfaGainInFrom Lower input gain range of the edfa in units of 0.1 db. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.21 |
| edfaGainInTo Upper input gain range of the edfa in units of 0.1 db. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.22 |
| edfaGainOutFrom Lower output gain range of the edfa in units of 0.1 db. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.23 |
| edfaGainOutTo Upper output gain range of the edfa in units of 0.1 db. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.24 |
| edfaPowerInFrom Lower input power range of the edfa in units of 0.1 dbm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.25 |
| edfaPowerInTo Upper input power range of the edfa in units of 0.1 dbm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.26 |
| edfaPowerOutFrom Lower output power range of the edfa in units of 0.1 dbm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.27 |
| edfaPowerOutTo Upper output power range of the edfa in units of 0.1 dbm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.28 |
| edfaFromChannel The first channel number supported by the edfa; 0 to ignore. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.29 |
| edfaRxPower The measured Rx Power.
The value is specified in ten'th of Dbm units increments, starting
from -30.0 dbm (e.g. value 0 means -30.0 dbm). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.3 |
| edfaToChannel The last channel number supported by the edfa; 0 to ignore. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.30 |
| edfaOscChannel The wavelenght of the optical supervisory channel e.g. 1510, 1490. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.31 |
| edfaRedBlueType The type of the edaf. | column | Enumeration | .1.3.6.1.4.1.4515.1.9.1.1.1.32 |
| edfaRole The role of the edaf. | column | Enumeration | .1.3.6.1.4.1.4515.1.9.1.1.1.33 |
| edfaFreeDescription A free text with additional edfa information. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4515.1.9.1.1.1.34 |
| edfaConfigSafetyThreshold The Eye Safety threshold level specified in dBm units.
The value given in 0.1 dBm units. The range starts with -50.0 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.35 |
| edfaSigOutputPower The measured Signal output Power.
The value is specified in ten'th of Dbm units increments, starting
from -30.0 dbm (e.g. value 0 means -30.0 dbm). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.36 |
| edfaLossPropagation Applicable for pre-amp.
Controls the pump behaviour in case of a LOS.
disabled - the pump is not shut-down to fasten the return-from-loss time.
enabled - the pump is shut-down wh… | column | Enumeration | .1.3.6.1.4.1.4515.1.9.1.1.1.37 |
| edfaPumpAdminStatus The desired state of the laser. The restart(3)
state indicates that the edfa pump should be restarted.
The restart(3) is not a state, thus it is not kept
in the configuration fil… | column | Enumeration | .1.3.6.1.4.1.4515.1.9.1.1.1.4 |
| edfaStatus This variable indicates the Line Status of the
Edfa module.
The edfaStatus is a bit map represented as a
sum, therefore, it can represent multiple failures (alarm… | column | Integer32 | .1.3.6.1.4.1.4515.1.9.1.1.1.6 |
| edfaVoa The computed VOA output attenuation specified in
0.1 dB units. From 0.0 to +15.0 dB. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4515.1.9.1.1.1.7 |
| edfaAutomaticMode Defines the Edfa automatic mode. If equals TRUE,
the Edfa control mode should selected automaticaly.
Otherwise it should be selected manualy. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.9.1.1.1.8 |
| edfaAdminControlMode Configure the Edfa control mode. This object
may be set only when edfaAtomaticMode is FALSE. | column | Enumeration | .1.3.6.1.4.1.4515.1.9.1.1.1.9 |