saRgDeviceMode

SA-RG-MIB · .1.3.6.1.4.1.1429.79.2.1.1.1

Object

scalar r/w Enumeration

Defines the mode of operation for the device.
This parameter is stored in non-vol and is multiSsid(1) by default.
Setting this object via SNMP will cause
the unit to reboot.
        This MIB will be superseded in the config file by TLV202.
        This MIB will read the proper value if set from TLV202.
        This MIB will be superseded by saRgIpMgmtLanMode inbridge(1) or mixed(4).
        disable(0):  Value will reflect when TLV202 is set to 0. Not all platforms have this value implemented.
        multiSsid(1): Default Value. Value supports IPv4RG with multiple SSID
                configuration and bridge mode via saRgIpMgmtLanMode MIB.
                Bridge mode is the same as eRouter disabled mode.
                IPV4RG is the non eRouter behavior that existed before
                in our router products.
        Ipv4(3): eRouter IPv4 only mode
        Ipv6(4): eRouter IPv6 only mode
        Dualstack(5): eRouter IPv4 and IPv6 dualstack
        Note: cableHome11(2) support is not available.

Context

MIB: SA-RG-MIB
OID: .1.3.6.1.4.1.1429.79.2.1.1.1
Type: scalar
Access: readwrite
Status: current
Parent: saRgDeviceBase
Siblings: 7

Syntax

Enumeration

Values & Constraints

Enumerated Values

`0`	disable
`1`	multiSsid
`3`	ipv4
`4`	ipv6
`5`	dualstack

Related Objects

Sibling Objects

Object	Type	Syntax	OID
saRgDeviceFactoryReset Set routerAndWifi(1) to restore default settings of both the router and wifi. Set routerOnly(2) to restore default settings of the router. Set wifi(3) to restore default settings …	scalar	Enumeration	`.1.3.6.1.4.1.1429.79.2.1.1.1002`
saRgDeviceResetDefaultEnable This object controls the reset to factory default functionality of the gateway. This prevents the local user from using the reset switch to gain access to the setup pages using th…	scalar	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.1429.79.2.1.1.2`
saRgDeviceRemoteWebAccessPort Defines what port to use for the WAN IP address of the gateway to be able to access RG web pages. This value is to be stored in non-vol and will persist across reboots. Only a fac…	scalar	INET-ADDRESS-MIBInetPortNumber	`.1.3.6.1.4.1.1429.79.2.1.1.4`
saRgDeviceLanLanIsolation This MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Lan Isolation allows you block IP …	scalar	Enumeration	`.1.3.6.1.4.1.1429.79.2.1.1.6`
saRgDeviceLanWlanIsolation This MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Wlan Isolation allows you block IP…	scalar	Enumeration	`.1.3.6.1.4.1.1429.79.2.1.1.7`
saRgDeviceIpv6Trans This MIB will control which IPv6 transition technology is enabled on the device. After setting this MIB to disable in the config file, IPv4 traffic will pass normally thro…	scalar	Enumeration	`.1.3.6.1.4.1.1429.79.2.1.1.8`
saRgDeviceIpv6Passthrough This MIB controls IPv6 passthrough on the RG and is applicable in bridge and router modes. When disabled the RG will function without any IPv6 passthrough When IPv6 passthrough is…	scalar	Enumeration	`.1.3.6.1.4.1.1429.79.2.1.1.9`