saRgDeviceLanWlanIsolation
SA-RG-MIB ·
.1.3.6.1.4.1.1429.79.2.1.1.7
Object
scalar
r/w
Enumeration
This MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Wlan Isolation allows you block IP access between CPEs connected to the Ethernet port and Wireless SSIDs. Use this mib in conjunction with saRgDeviceLanLanIsolation and saRgDot11BssApIsolation.x for complete isolation between CPEs connected to the RG. This MIB is written to non-vol and set to disable(0) after a factory reset. disable(0)- No Isolation enable(1)- Enable Isolation feature
Context
- MIB
- SA-RG-MIB
- OID
.1.3.6.1.4.1.1429.79.2.1.1.7- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- saRgDeviceBase
- Siblings
- 7
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| saRgDeviceMode Defines the mode of operation for the device.
This parameter is stored in non-vol and is multiSsid(1) by default.
Setting this object via SNMP will cause
the unit to reboot.
… | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.1 |
| saRgDeviceFactoryReset Set routerAndWifi(1) to restore default settings of both the router and wifi.
Set routerOnly(2) to restore default settings of the router.
Set wifi(3) to restore default settings … | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.1002 |
| saRgDeviceResetDefaultEnable This object controls the reset to factory default functionality
of the gateway. This prevents the local user from using the reset
switch to gain access to the setup pages using th… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1429.79.2.1.1.2 |
| saRgDeviceRemoteWebAccessPort Defines what port to use for the WAN IP address of the gateway
to be able to access RG web pages.
This value is to be stored in non-vol and will persist across reboots.
Only a fac… | scalar | INET-ADDRESS-MIBInetPortNumber | .1.3.6.1.4.1.1429.79.2.1.1.4 |
| saRgDeviceLanLanIsolation This MIB is only available in D3.0 products.
This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5).
Lan-Lan Isolation allows you block IP … | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.6 |
| saRgDeviceIpv6Trans This MIB will control which IPv6 transition technology is enabled on the device.
After setting this MIB to disable in the config file, IPv4 traffic will pass normally
thro… | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.8 |
| saRgDeviceIpv6Passthrough This MIB controls IPv6 passthrough on the RG and is applicable in bridge and router modes.
When disabled the RG will function without any IPv6 passthrough
When IPv6 passthrough is… | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.9 |