saRgDeviceIpv6Passthrough
SA-RG-MIB ·
.1.3.6.1.4.1.1429.79.2.1.1.9
Object
scalar
r/w
Enumeration
This MIB controls IPv6 passthrough on the RG and is applicable in bridge and router modes. When disabled the RG will function without any IPv6 passthrough When IPv6 passthrough is enabled in Bridge Mode the RG will drop all IPv4 traffic When IPv6 passthrough is enabled in router mode the RG will operate as normal for IPv4 traffic, but all IPv6 traffic will passthrough This MIB requires CM reboot. This MIB is written to non-vol and set to disable(0) after a factory reset.
Context
- MIB
- SA-RG-MIB
- OID
.1.3.6.1.4.1.1429.79.2.1.1.9- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- saRgDeviceBase
- Siblings
- 7
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| saRgDeviceMode Defines the mode of operation for the device.
This parameter is stored in non-vol and is multiSsid(1) by default.
Setting this object via SNMP will cause
the unit to reboot.
… | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.1 |
| saRgDeviceFactoryReset Set routerAndWifi(1) to restore default settings of both the router and wifi.
Set routerOnly(2) to restore default settings of the router.
Set wifi(3) to restore default settings … | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.1002 |
| saRgDeviceResetDefaultEnable This object controls the reset to factory default functionality
of the gateway. This prevents the local user from using the reset
switch to gain access to the setup pages using th… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1429.79.2.1.1.2 |
| saRgDeviceRemoteWebAccessPort Defines what port to use for the WAN IP address of the gateway
to be able to access RG web pages.
This value is to be stored in non-vol and will persist across reboots.
Only a fac… | scalar | INET-ADDRESS-MIBInetPortNumber | .1.3.6.1.4.1.1429.79.2.1.1.4 |
| saRgDeviceLanLanIsolation This MIB is only available in D3.0 products.
This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5).
Lan-Lan Isolation allows you block IP … | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.6 |
| saRgDeviceLanWlanIsolation This MIB is only available in D3.0 products.
This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5).
Lan-Wlan Isolation allows you block IP… | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.7 |
| saRgDeviceIpv6Trans This MIB will control which IPv6 transition technology is enabled on the device.
After setting this MIB to disable in the config file, IPv4 traffic will pass normally
thro… | scalar | Enumeration | .1.3.6.1.4.1.1429.79.2.1.1.8 |