rcIrigbTimeCode

RUGGEDCOM-IRIGB-MIB · .1.3.6.1.4.1.15004.4.10.1.3
MIB view Table view

Object

scalar r/w Enumeration 
This device uses the following convention to decode the IRIGB time code:
letter [B] represents IRIG-B format, [xx] represents [00] for PWM/TTL mode
of operation and [12] for AM operation. For example, Bxx7 represents B007 
for PWM/TTL operation and B127 for AM operation. Please note that only Bxx0, 
Bxx1, Bxx4 and Bxx5 time codes support IRIGB extensions.

Context

MIB
RUGGEDCOM-IRIGB-MIB
OID
.1.3.6.1.4.1.15004.4.10.1.3
Type
scalar
Access
readwrite
Status
current
Parent
rcIrigbBase
Siblings
16

Syntax

Enumeration

Values & Constraints

Enumerated Values
1bxx0
2bxx1
3bxx2
4bxx3
5bxx4
6bxx5
7bxx6
8bxx7

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rcIrigbStatus
The system synchronization status when IRIGB is a primary time source. If value of this object is changed, rcIrigbStatusChange notification will be sent.
scalarRUGGEDCOM-TIMECONFIG-MIBRcTimeSyncStatus.1.3.6.1.4.1.15004.4.10.1.1
rcIrigbOutputPWM1
Selects Operational mode of TTL output port. PWM mode complies with IRIG Standard 200-04. PPx provides generic pulse per x second interface to synchronize external devices.
scalarEnumeration.1.3.6.1.4.1.15004.4.10.1.10
rcIrigbPulseInterval1
Selects Pulse Interval in s for TTL output port. This parameter is used in conjunction with PPx in order to provides generic pulse per x second interface to synchronize external d…
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.11
rcIrigbPulseWidth1
Selects Pulse Width in ms for TTL output port. This parameter is used in conjunction with PPx to control the width of the pulse.
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.12
rcIrigbStartTime1
This parameter is used in conjunction with PPx to set the starting time of first PPx event. Note that this parameter must be set at least 15 seconds before the start of desired P…
scalarRcTimeStamp.1.3.6.1.4.1.15004.4.10.1.13
rcIrigbOutputPWM2
Selects Operational mode of TTL output port2. PWM mode complies with IRIG Standard 200-04. PPx provides generic pulse per x second interface to synchronize external devices.
scalarEnumeration.1.3.6.1.4.1.15004.4.10.1.14
rcIrigbPulseInterval2
Selects Pulse Interval in s for TTL output port2. This parameter is used in conjunction with PPx in order to provides generic pulse per x second interface to synchronize external …
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.15
rcIrigbPulseWidth2
Selects Pulse Width in ms for TTL output port2. This parameter is used in conjunction with PPx to control the width of the pulse.
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.16
rcIrigbStartTime2
This parameter is used in conjunction with PPx to set the starting time of first PPx event. Note that this parameter must be set at least 15 seconds before the start of desired P…
scalarRcTimeStamp.1.3.6.1.4.1.15004.4.10.1.17
rcIrigbAMOutput
Selects AM (Amplitude Modulation) mode of IRIGB port.
scalarEnumeration.1.3.6.1.4.1.15004.4.10.1.2
rcIrigbExt
IRIGB extensions use extra bits of the Control Functions (CF) portion of the IRIGB time code. Within this portion of the time code, bits are designated for additional features, i…
scalarEnumeration.1.3.6.1.4.1.15004.4.10.1.4
rcIrigbInput
Selects operational mode of IRIGB input port. IRIGB module is capable of interpreting IRIGB extensions such as C37.118-2011, C37.118-2005 and IEEE1344.
scalarEnumeration.1.3.6.1.4.1.15004.4.10.1.5
rcIrigbLockInt
To set time interval in minute with in which IRIGB receiver should acquire lock to the time source. Normally IRIGB receiver needs couple of minutes to lock the signal. Use…
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.6
rcIrigbCableComp
Cable compensation in ns may be desired to compensate for a long cable run in order to minimize the timing inaccuracy.
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.7
rcIrigbOFM
The current time offset between system and reference clocks.
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.8
rcIrigbFreqAdj
The current amount of discipline applied to the local frequency reference (TCXO).
scalarInteger32.1.3.6.1.4.1.15004.4.10.1.9