subnetMask
RPS-SC300-MIB ·
.1.3.6.1.4.1.1918.2.14.10.30.30
Object
scalar
r/w
OctetString
The manually set netmask. If set to 0.0.0.0, the controller will use DHCP or AutoIP. In which case this is the IP address that will be dynamically assigned to the controller by those protocols.
Context
- MIB
- RPS-SC300-MIB
- OID
.1.3.6.1.4.1.1918.2.14.10.30.30- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- communications
- Siblings
- 23
Syntax
OctetString
Values & Constraints
Object Constraints
range: 1-64
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| serialServerPort The port Number that the serial port traffic will be routed | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1918.2.14.10.30.10 |
| ipAddressAuto The IP address currently in use. This maybe set by auto-ip, dhcp or manually. | scalar | OctetString | .1.3.6.1.4.1.1918.2.14.10.30.100 |
| subnetMaskAuto Identifies which fragment of the IP address is the sub-network identity. This value and the IP Address must be set correctly to communicate using Ethernet. Consult your network ad… | scalar | OctetString | .1.3.6.1.4.1.1918.2.14.10.30.110 |
| gatewayAddressAuto Allows access to IP addresses outside your sub-network. Consult your network administrator. This maybe set by auto-ip, dhcp or manually. | scalar | OctetString | .1.3.6.1.4.1.1918.2.14.10.30.120 |
| autoIp If Enabled, Auto IP is available. DHCP is enabled when the ip address is configured to 0.0.0.0 and co-operates with auto ip. | scalar | EnableState | .1.3.6.1.4.1.1918.2.14.10.30.130 |
| webSessionTimeout If there is no user action for a time the web user will be log off. | scalar | min TimeIntervalInMinutes | .1.3.6.1.4.1.1918.2.14.10.30.140 |
| s3pAddress If the controller is connected to a serial S3P bus that supports multiple devices, this address is used to distinguish the devices. Otherwise it should remain at 1. | scalar | Unsigned16 | .1.3.6.1.4.1.1918.2.14.10.30.15 |
| webAccess HTTP Web interface access. | scalar | WebAccess | .1.3.6.1.4.1.1918.2.14.10.30.150 |
| blacklist Port scanner can cause problems, so we can blacklist the scanners source ip address. | scalar | EnableState | .1.3.6.1.4.1.1918.2.14.10.30.160 |
| blacklisted Port scanner can cause problems, so we can blacklist the scanners source ip address. | scalar | OctetString | .1.3.6.1.4.1.1918.2.14.10.30.170 |
| ipAddress The manually set IP address. If set to 0.0.0.0, the controller will use DHCP or AutoIP. In which case this is the IP address that will be dynamically assigned to the controller by… | scalar | OctetString | .1.3.6.1.4.1.1918.2.14.10.30.20 |
| s3pAccess Determines whether or not the S3P access is allowed. | scalar | S3pAccess | .1.3.6.1.4.1.1918.2.14.10.30.3 |
| gatewayAddress The manually set gateway address. If set to 0.0.0.0, the controller will use DHCP or AutoIP. In which case this is the IP address that will be dynamically assigned to the controll… | scalar | OctetString | .1.3.6.1.4.1.1918.2.14.10.30.50 |
| vlanId Identifies the virtual LAN circuit to connect to. Consult your network administrator. If in doubt, leave at zero. | scalar | Unsigned16 | .1.3.6.1.4.1.1918.2.14.10.30.51 |
| serial | node | - | .1.3.6.1.4.1.1918.2.14.10.30.53 |
| modbus | node | - | .1.3.6.1.4.1.1918.2.14.10.30.57 |
| snmpSettings | node | - | .1.3.6.1.4.1.1918.2.14.10.30.60 |
| node | - | .1.3.6.1.4.1.1918.2.14.10.30.65 | |
| sntp | node | - | .1.3.6.1.4.1.1918.2.14.10.30.70 |
| snmpAccess Determines how SNMP access is allowed. | scalar | SnmpAccessState | .1.3.6.1.4.1.1918.2.14.10.30.8 |
| webUserTable Table for webUser | table | - | .1.3.6.1.4.1.1918.2.14.10.30.80 |
| serialServerAccess Enables operation of pass-through from TCP to the serial port. | scalar | EnableState | .1.3.6.1.4.1.1918.2.14.10.30.9 |
| radius | node | - | .1.3.6.1.4.1.1918.2.14.10.30.90 |