generatorFailAlarmRecognitionPeriod
RPS-SC300-MIB ·
.1.3.6.1.4.1.1918.2.14.10.70.80.100
Object
scalar
r/w
s TimeIntervalInSeconds
Recognition period for the Generator Fail Alarm. The alarm will activate if the Generator Fail Alarm has been triggered for this period and AC has not been restored.
Context
- MIB
- RPS-SC300-MIB
- OID
.1.3.6.1.4.1.1918.2.14.10.70.80.100- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- s
- Parent
- generatorControl
- Siblings
- 20
Syntax
s TimeIntervalInSeconds
- Source
- TimeIntervalInSeconds
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| generatorOnFastCharge The controller will activate the generator control relay while fast charge is pending or active. | scalar | YesNo | .1.3.6.1.4.1.1918.2.14.10.70.80.111 |
| generatorOnEqualize The controller will activate the generator control relay while equalize is pending or active. | scalar | YesNo | .1.3.6.1.4.1.1918.2.14.10.70.80.112 |
| generatorOnAcPeakLoadReduction The controller will start the generator when PLR is active and the bus voltage has dropped to the PLR low voltage limit. | scalar | YesNo | .1.3.6.1.4.1.1918.2.14.10.70.80.114 |
| generatorOnMainsFailure The controller will activate the generator control relay when there is a mains failure. | scalar | YesNo | .1.3.6.1.4.1.1918.2.14.10.70.80.116 |
| acSupplyState Calculated AC Supply state. | scalar | SystemState | .1.3.6.1.4.1.1918.2.14.10.70.80.120 |
| generatorRunTimeRemaining The time left for the generator to run following a manual start. | scalar | s TimeIntervalInSeconds | .1.3.6.1.4.1.1918.2.14.10.70.80.130 |
| generatorState Indicates whether or not the controller believes that the generator is currently running. This information may be based on a digital input (if configured) or derived from other in… | scalar | EngineRunState | .1.3.6.1.4.1.1918.2.14.10.70.80.140 |
| generatorRefuelDate The time and date the generator was last refueled. | scalar | JulianDateUtc25 | .1.3.6.1.4.1.1918.2.14.10.70.80.150 |
| generatorRefuelVolume The amount of fuel added to the generator's fuel tank(s) during the last refuel. | scalar | L Float | .1.3.6.1.4.1.1918.2.14.10.70.80.160 |
| generatorBackupTime Estimated time for which the generator could continuously run based on the current fuel-level and historic fuel consumption. | scalar | s TimeIntervalInSeconds | .1.3.6.1.4.1.1918.2.14.10.70.80.170 |
| tankEmptyDateTime Best current estimate of the date at which the tank will run dry if the current characteristics of generator usage do not change. This is useful for installations that run the gen… | scalar | JulianDateUtc25 | .1.3.6.1.4.1.1918.2.14.10.70.80.180 |
| fuelLevel The volume of fuel in the generator's fuel tank(s). | scalar | L Float | .1.3.6.1.4.1.1918.2.14.10.70.80.190 |
| generatorControlRelay The relay used to control generator startup and shutdown. If this is set to None, the generator control process is disabled. | scalar | RelayMapping | .1.3.6.1.4.1.1918.2.14.10.70.80.200 |
| generatorStartupWiring Choose to match the way the generator control relay is wired. | scalar | GeneratorStartupWiring | .1.3.6.1.4.1.1918.2.14.10.70.80.210 |
| manualGeneratorRunTime This is the maximum time for which a manual run lasts. If, at the end of this time, automatic conditions are such to cause the generator to run, it will continue to run. | scalar | min TimeIntervalInMinutes | .1.3.6.1.4.1.1918.2.14.10.70.80.230 |
| fuelTankVolume The total volume of the generator's fuel tank(s). A value of 0 disables fuel related estimates. | scalar | L Float | .1.3.6.1.4.1.1918.2.14.10.70.80.240 |
| manualGeneratorStart This causes the generator to run for the configured time unless it is manually stopped. | scalar | NoData | .1.3.6.1.4.1.1918.2.14.10.70.80.260 |
| manualGeneratorStop This will end a manual generator run before the time has elapsed. It will not cause the generator to stop if it is running based on fast charge, equalize or AC failure. | scalar | NoData | .1.3.6.1.4.1.1918.2.14.10.70.80.270 |
| clearFuelConsumptionHistory The controller accumulates historic information on the average generator fuel consumption and, in applications that run the generator regularly, the average generator duty cycle. … | scalar | NoData | .1.3.6.1.4.1.1918.2.14.10.70.80.280 |
| generatorCurrent The total power produced by generator sources. | scalar | 0.01 kW Float | .1.3.6.1.4.1.1918.2.14.10.70.80.91 |