snmpFddiSMTConnectionPolicy
RFC1285-MIB ·
.1.3.6.1.2.1.10.15.1.2.1.12
Object
column
mandatory
r/w
Integer32
A value that indicates the connection policies
enforced at the station. A station sets the
corresponding policy for each of the connection
types that it rejects. The letter designations, X
and Y, in the 'rejectX-Y' names have the following
significance: X represents the PC-Type of the
local PORT and Y represents a PC-Neighbor in the
evaluation of Connection-Policy (PC-Type, PC-
Neighbor) that is done to determine the setting of
T-Val(3) in the PC-Signaling sequence (refer to
ANSI Section 9.6.3).
The value is a sum. This value initially takes
the value zero, then for each of the connection
policies currently enforced on the node, 2 raised
to a power is added to the sum. The powers are
according to the following table:
Policy Power
rejectA-A 0
rejectA-B 1
rejectA-S 2
rejectA-M 3
rejectB-A 4
rejectB-B 5
rejectB-S 6
rejectB-M 7
rejectS-A 8
rejectS-B 9
rejectS-S 10
rejectS-M 11
rejectM-A 12
rejectM-B 13
rejectM-S 14
rejectM-M 15
Implementors should note that the polarity of
these bits is different in different places in an
SMT system. Implementors should take appropriate
care.
Context
- MIB
- RFC1285-MIB
- OID
.1.3.6.1.2.1.10.15.1.2.1.12- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- snmpFddiSMTEntry
- Table
- snmpFddiSMTTable
- Siblings
- 18
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-65535
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| snmpFddiSMTIndex mandatory A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of th… | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.1 |
| snmpFddiSMTConfigCapabilities mandatory A value that indicates capabilities that are
present in the node. If 'holdAvailable' is
present, this indicates support of the optional
Hold Function (refer to ANSI SMT 9.4.3.2).… | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.10 |
| snmpFddiSMTConfigPolicy mandatory A value that indicates the configuration policies
currently enforced in the node (refer to ANSI SMT
9.4.3.2). The 'configurationHold' policy refers
to the Hold flag, and should n… | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.11 |
| snmpFddiSMTTNotify mandatory The timer used in the Neighbor Notification
protocol, reported in seconds and ranging from 2
to 30 seconds (refer to ANSI SMT 8.3.1). | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.13 |
| snmpFddiSMTStatusReporting mandatory Indicates whether the node implements the Status
Reporting Protocol. This object is included for
compatibility with products that were designed
prior to the adoption of this stan… | column | Enumeration | .1.3.6.1.2.1.10.15.1.2.1.14 |
| snmpFddiSMTECMState mandatory Indicates the current state of the ECM state
machine (refer to ANSI SMT 9.5.2). | column | Enumeration | .1.3.6.1.2.1.10.15.1.2.1.15 |
| snmpFddiSMTCFState mandatory The attachment configuration for the station or
concentrator (refer to ANSI SMT 9.7.4.3). | column | Enumeration | .1.3.6.1.2.1.10.15.1.2.1.16 |
| snmpFddiSMTHoldState mandatory This value indicates the current state of the
Hold function. The values are determined as
follows: 'holding-prm' is set if the primary ring
is operational and the Recovery Enabl… | column | Enumeration | .1.3.6.1.2.1.10.15.1.2.1.17 |
| snmpFddiSMTRemoteDisconnectFlag mandatory A flag indicating that the station was remotely
disconnected from the network. A station requires
a Connect Action (SM_CM_CONNECT.request (Connect))
to rejoin and clear the flag … | column | Enumeration | .1.3.6.1.2.1.10.15.1.2.1.18 |
| snmpFddiSMTStationAction mandatory This object, when read, always returns a value of
other(1). The behavior of setting this variable
to each of the acceptable values is as follows:
Other: R… | column | Enumeration | .1.3.6.1.2.1.10.15.1.2.1.19 |
| snmpFddiSMTStationId mandatory Uniquely identifies an FDDI station. | column | FddiSMTStationIdType | .1.3.6.1.2.1.10.15.1.2.1.2 |
| snmpFddiSMTOpVersionId mandatory The version that this station is using for its
operation (refer to ANSI 7.1.2.2). | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.3 |
| snmpFddiSMTHiVersionId mandatory The highest version of SMT that this station
supports (refer to ANSI 7.1.2.2). | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.4 |
| snmpFddiSMTLoVersionId mandatory The lowest version of SMT that this station
supports (refer to ANSI 7.1.2.2). | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.5 |
| snmpFddiSMTMACCt mandatory The number of MACs in the station or
concentrator. | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.6 |
| snmpFddiSMTNonMasterCt mandatory The number of Non Master PORTs (A, B, or S PORTs)
in the station or concentrator. | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.7 |
| snmpFddiSMTMasterCt mandatory The number of Master PORTs in a node. If the
node is not a concentrator, the value is zero. | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.8 |
| snmpFddiSMTPathsAvailable mandatory A value that indicates the PATH types available
in the station.
The value is a sum. This value initially takes
the value zero, then for each type of PATH that
this… | column | Integer32 | .1.3.6.1.2.1.10.15.1.2.1.9 |