an50WrlsMaster
REDLINE-AN50-MIB ·
.1.3.6.1.4.1.10728.2.16.2.2.6
Object
scalar
mandatory
r/w
Enumeration
The object contains the configured mode of the AN50 terminal. 1 = PTP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master
Context
- MIB
- REDLINE-AN50-MIB
- OID
.1.3.6.1.4.1.10728.2.16.2.2.6- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- an50ConfigWireless
- Siblings
- 22
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | ptpSlave |
2 | ptpMaster |
3 | pmpSlave |
4 | pmpMaster |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| an50WrlsChannel mandatory specifies the operating channel of the system,
within the 100 MHz available in the 5.8GHz UNII band.
To avoid interference, two PTP links operating in
the same phy… | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.1 |
| an50WrlsRfPortStatus mandatory The object specifies the status of the AN50s Wireless Port. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.10 |
| an50WrlsSaveConfig mandatory The object saves the entire config set of the AN50. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.11 |
| an50WrlsActivateConfig mandatory The object activates the entire config set of the AN50. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.12 |
| an50WrlsRadioEnable mandatory The object specifies whether radio transmission is enabled or disabled. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.13 |
| an50WrlsRfStatusErrorCode mandatory The object specifies the Error Code for the RF Status. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.14 |
| an50WrlsRfSignal mandatory The object specifies the Wireless Signal LED status. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.15 |
| an50WrlsLLMode mandatory Link length set mode. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.16 |
| an50WrlsLMU mandatory This object specifies the Link measurements unit (mile / Km). | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.17 |
| an50WrlsLL mandatory This object specifies the Link Length.
See an50WrlsLMU object for units. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.18 |
| an50ConfigScheduler | node | - | .1.3.6.1.4.1.10728.2.16.2.2.19 |
| an50WrlsTxPower mandatory The Tx Power of the AN-50 in dBm. Specifies the power level of the system,
which is preset at the factory and should not be altered. In the event
that this parameter needs to … | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.2 |
| an50ConfigDefGroup | node | - | .1.3.6.1.4.1.10728.2.16.2.2.20 |
| an50WrlsDFSAction mandatory This object specifies the action taken when another system
is detected on the same frequency | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.21 |
| an50WrlsAntennaGain mandatory Antenna Gain in dB. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.22 |
| an50WrlsATPEnabled mandatory This object specifies if the Automatic Transmitted Power Control
is enabled | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.23 |
| an50WrlsModReduction mandatory The Modulation Reduction Level of the AN-50. Applies when the
Adaptive rate is disabled. Specifies how many levels the system
must drop in modulation before beginning re-tra… | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.3 |
| an50WrlsAdaptiveMod mandatory Setting this attribute to AdaptiveRate(2) sets the system
to operate in adaptive modulation mode. It is recommended
to keep the AN-50 in this mode so that the system can
automa… | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.4 |
| an50WrlsUBR mandatory This object contains the desired net uncoded burst rate for the link.
Set uncoded burst rate in steps (0=6Mb/s, 1=9Mb/s, 2=12Mb/s,
3=18Mb/s, 4=24Mb/s, 5=36Mb/s, 6=48Mb/s, 7=54Mbs… | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.5 |
| an50WrlsVersion mandatory Sets the version of the AN50 system software. The software
can be remotely downloaded into the AN50. The system
comprises sufficient memory to hold two independent software load… | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.7 |
| an50WrlsEncryptCode mandatory The object contains the Encryption Key used for the
AN-50 terminal. Enter the MAC address of the remote
terminal to enable over-the-air data encryption. | scalar | OctetString | .1.3.6.1.4.1.10728.2.16.2.2.8 |
| an50WrlsCableAttenuation mandatory This object contains the Cable Attenuation for the AN-50 in dB. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.9 |