an50WrlsAdaptiveMod
REDLINE-AN50-MIB ·
.1.3.6.1.4.1.10728.2.16.2.2.4
Object
scalar
mandatory
r/w
Enumeration
Setting this attribute to AdaptiveRate(2) sets the system to operate in adaptive modulation mode. It is recommended to keep the AN-50 in this mode so that the system can automatically adjust the modulation level to the highest possible data rate based on measured RF performance. The user can define the minimum desired modulation level by setting the Main rate parameter. If the system meets this data rate, then the Signal LED on the front panel will light continuously green. If packet errors exceed one out of a million, the system will automatically lower the modulation level to maintain the link. In this case, the LED will flash green. If errors continue when the system reaches the lowest modulation level, the LED will flash red to indicate a failed RF link. The user can also disable the dynamic modulation mode by disabling Adaptive Modulation. In this mode, the user is required to set the Burst Rate and the Modulation Reduction Level. It is recommended not to operate the system in manual mode, as this mode is intended primarily for field support. Note the Signal LED will light solid green when the packet error rate is less than 1 out of a million. When the errors exceed this limit, the LED will not illuminate, indicating the RF link has failed.
Context
- MIB
- REDLINE-AN50-MIB
- OID
.1.3.6.1.4.1.10728.2.16.2.2.4- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- an50ConfigWireless
- Siblings
- 22
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | notAdaptiveRate |
2 | adaptiveRate |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| an50WrlsChannel mandatory specifies the operating channel of the system,
within the 100 MHz available in the 5.8GHz UNII band.
To avoid interference, two PTP links operating in
the same phy… | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.1 |
| an50WrlsRfPortStatus mandatory The object specifies the status of the AN50s Wireless Port. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.10 |
| an50WrlsSaveConfig mandatory The object saves the entire config set of the AN50. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.11 |
| an50WrlsActivateConfig mandatory The object activates the entire config set of the AN50. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.12 |
| an50WrlsRadioEnable mandatory The object specifies whether radio transmission is enabled or disabled. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.13 |
| an50WrlsRfStatusErrorCode mandatory The object specifies the Error Code for the RF Status. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.14 |
| an50WrlsRfSignal mandatory The object specifies the Wireless Signal LED status. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.15 |
| an50WrlsLLMode mandatory Link length set mode. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.16 |
| an50WrlsLMU mandatory This object specifies the Link measurements unit (mile / Km). | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.17 |
| an50WrlsLL mandatory This object specifies the Link Length.
See an50WrlsLMU object for units. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.18 |
| an50ConfigScheduler | node | - | .1.3.6.1.4.1.10728.2.16.2.2.19 |
| an50WrlsTxPower mandatory The Tx Power of the AN-50 in dBm. Specifies the power level of the system,
which is preset at the factory and should not be altered. In the event
that this parameter needs to … | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.2 |
| an50ConfigDefGroup | node | - | .1.3.6.1.4.1.10728.2.16.2.2.20 |
| an50WrlsDFSAction mandatory This object specifies the action taken when another system
is detected on the same frequency | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.21 |
| an50WrlsAntennaGain mandatory Antenna Gain in dB. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.22 |
| an50WrlsATPEnabled mandatory This object specifies if the Automatic Transmitted Power Control
is enabled | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.23 |
| an50WrlsModReduction mandatory The Modulation Reduction Level of the AN-50. Applies when the
Adaptive rate is disabled. Specifies how many levels the system
must drop in modulation before beginning re-tra… | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.3 |
| an50WrlsUBR mandatory This object contains the desired net uncoded burst rate for the link.
Set uncoded burst rate in steps (0=6Mb/s, 1=9Mb/s, 2=12Mb/s,
3=18Mb/s, 4=24Mb/s, 5=36Mb/s, 6=48Mb/s, 7=54Mbs… | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.5 |
| an50WrlsMaster mandatory The object contains the configured mode of the AN50 terminal.
1 = PTP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.6 |
| an50WrlsVersion mandatory Sets the version of the AN50 system software. The software
can be remotely downloaded into the AN50. The system
comprises sufficient memory to hold two independent software load… | scalar | Enumeration | .1.3.6.1.4.1.10728.2.16.2.2.7 |
| an50WrlsEncryptCode mandatory The object contains the Encryption Key used for the
AN-50 terminal. Enter the MAC address of the remote
terminal to enable over-the-air data encryption. | scalar | OctetString | .1.3.6.1.4.1.10728.2.16.2.2.8 |
| an50WrlsCableAttenuation mandatory This object contains the Cable Attenuation for the AN-50 in dB. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.16.2.2.9 |