rbnL2tpPCfgHelloTimer

RBN-L2TP-MIB · .1.3.6.1.4.1.2352.2.28.1.1.1.28
MIB view Table view

Object

column r/w seconds Unsigned32 
This object defines the interval (in seconds) in
which Hello (or keep-alive) packets are to be sent
by local tunnels belonging to this tunnel configuration.

Context

MIB
RBN-L2TP-MIB
OID
.1.3.6.1.4.1.2352.2.28.1.1.1.28
Type
column
Access
readwrite
Status
current
Units
seconds
Parent
rbnL2tpPeerCfgEntry
Table
rbnL2tpPeerCfgTable
Siblings
34

Syntax

seconds Unsigned32

Values & Constraints

Object Constraints
range: 0-3600

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rbnL2tpMibPeerName
This object identifies the name of the Peer on the local system. This peer is the name of an identifier for a tunnel configuration and each tunnel that is assigned to this peer…
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.1
rbnL2tpPCfgLocalIPAddType
This object identifies the address type contained in rbnL2tpPCfgLocalIPAdd.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.2352.2.28.1.1.1.10
rbnL2tpPCfgLocalIPAdd
This object indicates the local IP address for this tunnel (utilized only with UDP).
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.2352.2.28.1.1.1.11
rbnL2tpPCfgMode
This object indicates whether the peer is operating as an LNS, a LAC, or both.
columnLacLnsType.1.3.6.1.4.1.2352.2.28.1.1.1.12
rbnL2tpPCfgMaxTunnels
This object indicates the maximum number of tunnels that may be configured on this peer.
columnSNMPv2-SMIGauge32.1.3.6.1.4.1.2352.2.28.1.1.1.14
rbnL2tpPCfgMaxSesPerTun
This object indicates the maximum number of sessions that may be allocated to one tunnel.
columnSNMPv2-SMIGauge32.1.3.6.1.4.1.2352.2.28.1.1.1.15
rbnL2tpPCfgCtlRetranCnt
This object indicates a count of the number of times that a control packet was retransmitted.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.2352.2.28.1.1.1.16
rbnL2tpPCfgCtlRetranTO
This object indicates the control retransmit timeout in seconds.
columnseconds Unsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.17
rbnL2tpPCfgSessAuth
This object indicates the session authentication type.
columnAuthType.1.3.6.1.4.1.2352.2.28.1.1.1.18
rbnL2tpPCfgCtlWin
This object indicates the control window size.
columnUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.19
rbnL2tpPCfgMedia
This object identifies the transport media utilized between communicating peers. A media length of 0 means that no transport media type was set.
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.2
rbnL2tpPCfgDNIS
This object indicates whether the critera used for a tunnel switch is Dialed Number Identification String first (a value of (1)), DNIS only (a value of (2)) or the no preference…
columnDNISType.1.3.6.1.4.1.2352.2.28.1.1.1.20
rbnL2tpPCfgPoliceRate
This object indicates the received aggregate stream limit, in kilobits per second.
columnkbps SNMPv2-SMIUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.21
rbnL2tpPCfgPoliceBurst
This object indicates the packet burst tolerance for tunnels received by this peer group.
columnkbps SNMPv2-SMIUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.22
rbnL2tpPCfgLimitRate
This object indicates the limit of the aggregate packet stream transmitted through a tunnel in kilobits per second (kpbs).
columnkbps SNMPv2-SMIUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.23
rbnL2tpPCfgLimitBurst
This object indicates the the packet burst tolerance limit transmitted on a tunnel.
columnkbps SNMPv2-SMIUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.24
rbnL2tpPCfgGroup
This object indicates the l2tp group which is assigned to this peer. Each peer configuration may be assigned only one tunnel group. A length of 0 means that the group name was no…
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.2352.2.28.1.1.1.25
rbnL2tpPCfgPref
This object indicates the RADIUS based preference number (used by tunnel groups only). A lower number indicates a more favorible preference.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.26
rbnL2tpPCfgPasswd
This object indicates the password for this account utilized when performing the connection handshake protocol with the remote host. A length of 0 indicates that no password has b…
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.27
rbnL2tpPCfgRecQue
This object indicates whether there is receive queueing of out of sequence messages. A value of true (1) indicates that the messages are queued.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2352.2.28.1.1.1.29
rbnL2tpPCfgVendor
This object identifies the vendor of L2TP stack running on the remote peer. The length of the string will be zero if no vendor name can be obtained from the peer.
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.3
rbnL2tpPCfgSessContext
This object indicates the name of the session context. A size of 0 indicates that the context could not be determined. Any context name length greater than 80 will be truncated…
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.30
rbnL2tpPCfgSessService
The service group to which this session belongs. A length of 0 indicates that no service group was assigned.
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.31
rbnL2tpPCfgEthEncap
This object indicates the ethernet encap type.
columnEthEncapType.1.3.6.1.4.1.2352.2.28.1.1.1.32
rbnL2tpPCfgEthSession
This object indicates the ethernet session of which this is a part. This is only set for non PPPoE sessions otherwise it will have a zero length.
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.33
rbnL2tpPCfgTunnelCount
This object indicates the number of tunnels that are active for this peer configuration.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.2352.2.28.1.1.1.34
rbnL2tpPCfgTunCtlErrs
This object is a count of the number of tunnel control errors encountered by tunnels connected to this peer.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.2352.2.28.1.1.1.35
rbnL2tpPCfgSessionCount
This object is a count of the number of sessions that are part of this peer.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.2352.2.28.1.1.1.36
rbnL2tpPCfgRev
This object identifies the firmware revision for the L2TP protocol stack running on the remote peer.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2352.2.28.1.1.1.4
rbnL2tpPCfgHostName
This object identifies the name assigned to this peer on the remote host system. A host name length of 0 means that this information could not be obtained from the remote host.
columnOctetString.1.3.6.1.4.1.2352.2.28.1.1.1.5
rbnL2tpPCfgRadius
This object indicates whether or not a RADIUS server has been configured for this peer group. A value of true (1) indicates that there is a RADIUS server and it will be used for …
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2352.2.28.1.1.1.6
rbnL2tpPCfgRemIPAddType
This object identifies the address type contained in rbnL2tpPCfgRemIPAdd.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.2352.2.28.1.1.1.7
rbnL2tpPCfgRemIPAdd
This object identifies the remote IP address for this tunnel (utilized only with User Datagram Protocol).
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.2352.2.28.1.1.1.8
rbnL2tpPCfgStatic
This objects indicates whether the tunnel is static or dynamic. A value of true (1) means that it is static. A value of (2) indicates that it is dynamic.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2352.2.28.1.1.1.9