rcWlanConfigRemoteVlanStg

RAPID-CITY · .1.3.6.1.4.1.2272.1.207.1.11
MIB view Table view

Object

scalar r/w Integer32 
The stg id for the remote vlan in the STP/MSTP mode.
In STP mode, the stg range is 1 to 64.
IN MSTP mode, the msti range is 0 to 63.
Setting to 255 is used to remove the valid stg/mstp from wlan.

Context

MIB
RAPID-CITY
OID
.1.3.6.1.4.1.2272.1.207.1.11
Type
scalar
Access
readwrite
Status
current
Parent
rcWlanScalars
Siblings
12

Syntax

Integer32

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rcWlanVlanReserveVlanList
The object is used as bitfield to indicate all the VLANs that are reserved. Each VLAN is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.
scalarOctetString.1.3.6.1.4.1.2272.1.207.1.1
rcWlanConfigSmltTcpUdpBasePort
TCP/UDP port to be used in SMLT.
scalarUnsigned32.1.3.6.1.4.1.2272.1.207.1.10
rcWlanConfigManagementAddressType
This object indicates the type of address contained in the object rcWlanConfigManagementAddress.
scalarINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.2272.1.207.1.12
rcWlanConfigManagementAddress
This address is used as the management interface of the wireless switch.
scalarINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.2272.1.207.1.13
rcWlanVlanReserveNumberVlans
The object contains the number of reserved VLANs.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.207.1.2
rcWlanVlanReserveVlanInUse
The object indicates if a Vlan Id from the reserved pool is in use.
scalarOctetString.1.3.6.1.4.1.2272.1.207.1.3
rcWlanVlanReserveVlanInUseBySmlt
The object indicates if a Vlan Id from the reserved pool is in use by SMLT.
scalarOctetString.1.3.6.1.4.1.2272.1.207.1.4
rcWlanVlanReserveSmltConfigMatch
The object indicates if a Vlan Id from the reserved pool is the same for SMLT peers.
scalarOctetString.1.3.6.1.4.1.2272.1.207.1.5
rcWlanConfigSystemSmltDataIPAddressType
This object indicates the type of internet address in the corresponding instance of rcWlanConfigSystemSmltDataIPAddress. Currently,only the values ipv4(1) and ipv6(2) are…
scalarINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.2272.1.207.1.6
rcWlanConfigSystemSmltDataIPAddress
This object contains the IP address that will be used for Wireless LAN switch SMLT data tunnel.
scalarOctetString.1.3.6.1.4.1.2272.1.207.1.7
rcWlanConfigSmltHoldDownTimer
Timer value, the range of value is from 0 to 3600. Do not start forwarding data until local syncronization is done.
scalarInteger32.1.3.6.1.4.1.2272.1.207.1.8
rcWlanConfigSmltEnabled
This is used to enable SMLT wireless feature. A value of true(1) means enabled.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.207.1.9