rcChasPowerManagementFanCheckOriginalState
RAPID-CITY ·
.1.3.6.1.4.1.2272.1.4.57
Object
scalar
SNMPv2-TCTruthValue
The on or off value of fan check which the switch has booted with. The value does not take effect till the next reboot.
Context
- MIB
- RAPID-CITY
- OID
.1.3.6.1.4.1.2272.1.4.57- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- rcChassis
- Siblings
- 67
Values & Constraints
Object Constraints
range: 0-15
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rcChasType Chassis Type | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.1 |
| rcPort | node | - | .1.3.6.1.4.1.2272.1.4.10 |
| rcPortLock | node | - | .1.3.6.1.4.1.2272.1.4.11 |
| rcChasAruMode The ARU mode the chassis is operating in. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.12 |
| rcChasQuidMode The Quid mode the chassis is operating in. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.13 |
| rcChasEocModeAdminStatus Used to specify the Enforce Operational
Configuration Mode(EOC) of the system. When a
device is configured with hardware of different
revisions, the system will initialize in som… | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.14 |
| rcChasEocModeOperStatus Used to indicate the Enforce Operational
Configuration Mode(EOC) of the system. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.15 |
| rcAgentTable Agents in a chassis table | table | - | .1.3.6.1.4.1.2272.1.4.16 |
| rcChasBrouterPorts Used to indicate which ports in the system are
configured as Brouter ports. | scalar | PortSet | .1.3.6.1.4.1.2272.1.4.17 |
| rcChasGlobalFilterEnable Used to enable/disable global filters in the
system. This variable is currently not supported. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.18 |
| rcChasVlanBySrcMacEnable Used to enable/disable source MAC based VLANs
in the system. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.19 |
| rcChasSerialNumber Unique serial number for this chassis. | scalar | OctetString | .1.3.6.1.4.1.2272.1.4.2 |
| rcChasDiffServEcnCompatibilityEnable Used to enable/disable the Explicit Congestion
Notification(ECN) compatibility feature.
When set to FALSE , the system will mask the ECN bits
in the DS field while re-marking DSCP… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.20 |
| rcChasNewEnhancedOperMode Enhanced operational mode. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.21 |
| rcChasNewEMMode This configuration is for enabling/disabling 128K
mode. The change will take effect upon reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.22 |
| rcChasEmModeError Used to indicate the Em-mode error status | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.23 |
| rcChasEnhancedOperMode Enhanced Operational mode the switch currently has
booted and will remain the same until the next reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.24 |
| rcChasEMMode EM mode the switch currently has booted and
will remain the same until the next reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.25 |
| rcChasFtpDaemonInSecondaryCpu Used to enable/disable FTP daemon in 2nd cpu. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.26 |
| rcChasSmltOnSingleCpEnable Enable SMLT on single CP feature in the switch
Not supported in VSP 3.3 | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.27 |
| rcChasNewVlanOptmMode Vlan Optimization mode. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.28 |
| rcChasVlanOptmMode Vlan Optimization mode the switch currently has
booted and will remain the same until the next
reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.29 |
| rcChasHardwareRevision Device hardware revision level | scalar | OctetString | .1.3.6.1.4.1.2272.1.4.3 |
| rcLaunchPad | node | - | .1.3.6.1.4.1.2272.1.4.30 |
| rcChasNaapEnable To enable/disbale to napp feature. | scalar | EnableValue | .1.3.6.1.4.1.2272.1.4.31 |
| rcChasGlobalFilterOrderingEnable Global Filter ordering in the system. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.32 |
| rcChasNewGlobalFilterOrderingEnable This configuration is for enabling/disabling
global filter ordering. The change will take
effect upon reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.33 |
| rcChasWsmDirectMode This is for enabling/disabling configuration
of same community strings on the WSM and 8600/8800.
This is for allowing users to connect directly
via SNMP to the WSM blade. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.34 |
| rcChasRspMode This configuration is for enabling/disabling 256K
mode. The change will take effect upon reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.35 |
| rcChasRspOperMode R-mode the switch currently has booted and
will remain the same until the next reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.36 |
| rcChasRspModeError Used to indicate the r-mode error status | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.37 |
| rcChasPOE | node | - | .1.3.6.1.4.1.2272.1.4.38 |
| rcRepeater | node | - | .1.3.6.1.4.1.2272.1.4.39 |
| rcChasNumSlots The number of slots in the chassis available for
plug-in cards. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.4 |
| rcChasMcastCheckPktEnable Used to enable/disable Multicast check packet in the
system. This change will take effect upon reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.40 |
| rcChasSystemMonitorEnable Enable/Disable System monitoring in the switch | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.41 |
| rcChasSysMonMonitoringEnable Dyanamically Enable/Disable SystemMonitor monitoring
engine in the switch | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.42 |
| rcChasSysMonDetectionTime System Monitor Detection time in seconds | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.43 |
| rcChasNewMulticastResourceReservation Used to reserve MGIDs for IP Multicast.
The change will take effect upon reboot. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.44 |
| rcChasMulticastResourceReservation MGIDs the switch currently has reserved for IP
Multicast; will remain the same until the next
reboot. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.45 |
| rcChasNewMaxVlanResourceReservation A mode where all MGIDs are reserved for VLAN use
only; no IPMC. The change will take effect upon
reboot. | scalar | EnableValue | .1.3.6.1.4.1.2272.1.4.46 |
| rcChasMaxVlanResourceReservation Tells if all MGIDs are reserved for VLAN use. Will
remain the same until the next reboot. | scalar | EnableValue | .1.3.6.1.4.1.2272.1.4.47 |
| rcChasMgidUsageVlanCurrent Number of MGIDs currently used for VLAN, including
SMLT | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.48 |
| rcChasMgidUsageVlanRemaining Number of MGIDs remaining allocated for VLAN | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.49 |
| rcChasNumPorts The total number of ports currently installed in
the chassis. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.5 |
| rcChasMgidUsageMulticastCurrent Number of MGIDs currently used for IPMC | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.50 |
| rcChasMgidUsageMulticastRemaining Number of MGIDs remaining allocated for IPMC | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.51 |
| rcChasPowerManagementEnable Turn on or off Chassis Power Management. The
configuration will take effect upon reboot.
This object is not applicable to VSP | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.52 |
| rcChasForceTopologyIpFlagEnable Used to enable/disable flag which is used to set the CLIP-ip as topology ip | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.53 |
| rcChasCircuitlessIpId The Clip-Id set by the user to be used as Topology-ip.
0' means no circuitless IP id while '1..256' is valid
circuitless Id | scalar | Integer32 | .1.3.6.1.4.1.2272.1.4.54 |
| rcChasPowerManagementOriginalEnable On or off value of Chassis Power Management which the
switch has currently booted. It will remain the same
until the next reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.55 |
| rcChasPowerManagementFanCheck Turn on or off the Fan Check functionility of Chassis
Power Management. The value takes effect only on reboot. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.56 |
| rcChasEsmHashIndex This is for enabling/disabling hashing on the upper 24 bits of the UNI for ESM card | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.58 |
| rcChasSwitchFabricRedundancy Turn on or off 2:1 Redundancy for 8011co Chassis | scalar | EnableValue | .1.3.6.1.4.1.2272.1.4.59 |
| rcChasTestResult Chassis start-up diagnostic tests. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.4.6 |
| rcChasSystemDefault Used to default the system | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.60 |
| rcChasTakeIOCardOfflineEnable Enable/Disable IO Card to go offline when
F2E sees excessive resets. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.61 |
| rcChasAutoResetFabricEnable Enable/Disable fabric to be reset automatically
on fab mem full error. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.62 |
| rcChasSecurityConsoleFlag Used to enable/disable flag which is used for
Security Console.When it is enabled, the console
connection works only with the null modem cable | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.63 |
| rcChasRcBridgeFdbOldQueryFlagEnable Used to enable/disable rcBridgeNewFdbTable for
fdb query | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.64 |
| rcChasLed | node | - | .1.3.6.1.4.1.2272.1.4.65 |
| rcChasPartNumber Device part number or PEC code | scalar | OctetString | .1.3.6.1.4.1.2272.1.4.66 |
| rcChasModelName Chassis model name. For APLS platform, it is model name
which is in teh seeprom | scalar | OctetString | .1.3.6.1.4.1.2272.1.4.67 |
| rcChasBrandName Chassis brand name. For APLS platform, it is programmed
in the seeprom | scalar | OctetString | .1.3.6.1.4.1.2272.1.4.68 |
| rcChasFan | node | - | .1.3.6.1.4.1.2272.1.4.7 |
| rcChasPowerSupply | node | - | .1.3.6.1.4.1.2272.1.4.8 |
| rcCard | node | - | .1.3.6.1.4.1.2272.1.4.9 |