rcChasEocModeAdminStatus

RAPID-CITY · .1.3.6.1.4.1.2272.1.4.14
MIB view Table view

Object

scalar r/w Enumeration 
Used to specify the Enforce Operational
Configuration Mode(EOC) of the system.  When a
device is configured with hardware of different
revisions, the system will initialize in some
deterministic manner (e.g., the lowest common
denominator that makes sense based on the hardware
configuration).  This is the 'default(0)' mode.
The user can override this behavior by manually
specifying the EOC Mode they would like.

Context

MIB
RAPID-CITY
OID
.1.3.6.1.4.1.2272.1.4.14
Type
scalar
Access
readwrite
Status
current
Parent
rcChassis
Siblings
67

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rcChasType
Chassis Type
scalarEnumeration.1.3.6.1.4.1.2272.1.4.1
rcPortnode-.1.3.6.1.4.1.2272.1.4.10
rcPortLocknode-.1.3.6.1.4.1.2272.1.4.11
rcChasAruMode
The ARU mode the chassis is operating in.
scalarEnumeration.1.3.6.1.4.1.2272.1.4.12
rcChasQuidMode
The Quid mode the chassis is operating in.
scalarEnumeration.1.3.6.1.4.1.2272.1.4.13
rcChasEocModeOperStatus
Used to indicate the Enforce Operational Configuration Mode(EOC) of the system.
scalarEnumeration.1.3.6.1.4.1.2272.1.4.15
rcAgentTable
Agents in a chassis table
table-.1.3.6.1.4.1.2272.1.4.16
rcChasBrouterPorts
Used to indicate which ports in the system are configured as Brouter ports.
scalarPortSet.1.3.6.1.4.1.2272.1.4.17
rcChasGlobalFilterEnable
Used to enable/disable global filters in the system. This variable is currently not supported.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.18
rcChasVlanBySrcMacEnable
Used to enable/disable source MAC based VLANs in the system.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.19
rcChasSerialNumber
Unique serial number for this chassis.
scalarOctetString.1.3.6.1.4.1.2272.1.4.2
rcChasDiffServEcnCompatibilityEnable
Used to enable/disable the Explicit Congestion Notification(ECN) compatibility feature. When set to FALSE , the system will mask the ECN bits in the DS field while re-marking DSCP…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.20
rcChasNewEnhancedOperMode
Enhanced operational mode.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.21
rcChasNewEMMode
This configuration is for enabling/disabling 128K mode. The change will take effect upon reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.22
rcChasEmModeError
Used to indicate the Em-mode error status
scalarEnumeration.1.3.6.1.4.1.2272.1.4.23
rcChasEnhancedOperMode
Enhanced Operational mode the switch currently has booted and will remain the same until the next reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.24
rcChasEMMode
EM mode the switch currently has booted and will remain the same until the next reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.25
rcChasFtpDaemonInSecondaryCpu
Used to enable/disable FTP daemon in 2nd cpu.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.26
rcChasSmltOnSingleCpEnable
Enable SMLT on single CP feature in the switch Not supported in VSP 3.3
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.27
rcChasNewVlanOptmMode
Vlan Optimization mode.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.28
rcChasVlanOptmMode
Vlan Optimization mode the switch currently has booted and will remain the same until the next reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.29
rcChasHardwareRevision
Device hardware revision level
scalarOctetString.1.3.6.1.4.1.2272.1.4.3
rcLaunchPadnode-.1.3.6.1.4.1.2272.1.4.30
rcChasNaapEnable
To enable/disbale to napp feature.
scalarEnableValue.1.3.6.1.4.1.2272.1.4.31
rcChasGlobalFilterOrderingEnable
Global Filter ordering in the system.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.32
rcChasNewGlobalFilterOrderingEnable
This configuration is for enabling/disabling global filter ordering. The change will take effect upon reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.33
rcChasWsmDirectMode
This is for enabling/disabling configuration of same community strings on the WSM and 8600/8800. This is for allowing users to connect directly via SNMP to the WSM blade.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.34
rcChasRspMode
This configuration is for enabling/disabling 256K mode. The change will take effect upon reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.35
rcChasRspOperMode
R-mode the switch currently has booted and will remain the same until the next reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.36
rcChasRspModeError
Used to indicate the r-mode error status
scalarEnumeration.1.3.6.1.4.1.2272.1.4.37
rcChasPOEnode-.1.3.6.1.4.1.2272.1.4.38
rcRepeaternode-.1.3.6.1.4.1.2272.1.4.39
rcChasNumSlots
The number of slots in the chassis available for plug-in cards.
scalarInteger32.1.3.6.1.4.1.2272.1.4.4
rcChasMcastCheckPktEnable
Used to enable/disable Multicast check packet in the system. This change will take effect upon reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.40
rcChasSystemMonitorEnable
Enable/Disable System monitoring in the switch
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.41
rcChasSysMonMonitoringEnable
Dyanamically Enable/Disable SystemMonitor monitoring engine in the switch
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.42
rcChasSysMonDetectionTime
System Monitor Detection time in seconds
scalarInteger32.1.3.6.1.4.1.2272.1.4.43
rcChasNewMulticastResourceReservation
Used to reserve MGIDs for IP Multicast. The change will take effect upon reboot.
scalarInteger32.1.3.6.1.4.1.2272.1.4.44
rcChasMulticastResourceReservation
MGIDs the switch currently has reserved for IP Multicast; will remain the same until the next reboot.
scalarInteger32.1.3.6.1.4.1.2272.1.4.45
rcChasNewMaxVlanResourceReservation
A mode where all MGIDs are reserved for VLAN use only; no IPMC. The change will take effect upon reboot.
scalarEnableValue.1.3.6.1.4.1.2272.1.4.46
rcChasMaxVlanResourceReservation
Tells if all MGIDs are reserved for VLAN use. Will remain the same until the next reboot.
scalarEnableValue.1.3.6.1.4.1.2272.1.4.47
rcChasMgidUsageVlanCurrent
Number of MGIDs currently used for VLAN, including SMLT
scalarInteger32.1.3.6.1.4.1.2272.1.4.48
rcChasMgidUsageVlanRemaining
Number of MGIDs remaining allocated for VLAN
scalarInteger32.1.3.6.1.4.1.2272.1.4.49
rcChasNumPorts
The total number of ports currently installed in the chassis.
scalarInteger32.1.3.6.1.4.1.2272.1.4.5
rcChasMgidUsageMulticastCurrent
Number of MGIDs currently used for IPMC
scalarInteger32.1.3.6.1.4.1.2272.1.4.50
rcChasMgidUsageMulticastRemaining
Number of MGIDs remaining allocated for IPMC
scalarInteger32.1.3.6.1.4.1.2272.1.4.51
rcChasPowerManagementEnable
Turn on or off Chassis Power Management. The configuration will take effect upon reboot. This object is not applicable to VSP
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.52
rcChasForceTopologyIpFlagEnable
Used to enable/disable flag which is used to set the CLIP-ip as topology ip
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.53
rcChasCircuitlessIpId
The Clip-Id set by the user to be used as Topology-ip. 0' means no circuitless IP id while '1..256' is valid circuitless Id
scalarInteger32.1.3.6.1.4.1.2272.1.4.54
rcChasPowerManagementOriginalEnable
On or off value of Chassis Power Management which the switch has currently booted. It will remain the same until the next reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.55
rcChasPowerManagementFanCheck
Turn on or off the Fan Check functionility of Chassis Power Management. The value takes effect only on reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.56
rcChasPowerManagementFanCheckOriginalState
The on or off value of fan check which the switch has booted with. The value does not take effect till the next reboot.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.57
rcChasEsmHashIndex
This is for enabling/disabling hashing on the upper 24 bits of the UNI for ESM card
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.58
rcChasSwitchFabricRedundancy
Turn on or off 2:1 Redundancy for 8011co Chassis
scalarEnableValue.1.3.6.1.4.1.2272.1.4.59
rcChasTestResult
Chassis start-up diagnostic tests.
scalarEnumeration.1.3.6.1.4.1.2272.1.4.6
rcChasSystemDefault
Used to default the system
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.60
rcChasTakeIOCardOfflineEnable
Enable/Disable IO Card to go offline when F2E sees excessive resets.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.61
rcChasAutoResetFabricEnable
Enable/Disable fabric to be reset automatically on fab mem full error.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.62
rcChasSecurityConsoleFlag
Used to enable/disable flag which is used for Security Console.When it is enabled, the console connection works only with the null modem cable
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.63
rcChasRcBridgeFdbOldQueryFlagEnable
Used to enable/disable rcBridgeNewFdbTable for fdb query
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.64
rcChasLednode-.1.3.6.1.4.1.2272.1.4.65
rcChasPartNumber
Device part number or PEC code
scalarOctetString.1.3.6.1.4.1.2272.1.4.66
rcChasModelName
Chassis model name. For APLS platform, it is model name which is in teh seeprom
scalarOctetString.1.3.6.1.4.1.2272.1.4.67
rcChasBrandName
Chassis brand name. For APLS platform, it is programmed in the seeprom
scalarOctetString.1.3.6.1.4.1.2272.1.4.68
rcChasFannode-.1.3.6.1.4.1.2272.1.4.7
rcChasPowerSupplynode-.1.3.6.1.4.1.2272.1.4.8
rcCardnode-.1.3.6.1.4.1.2272.1.4.9