pktSwchProfileParTreatS
RAD-MIB ·
.1.3.6.1.4.1.164.8.2.1.1.1.22
Object
column
r/w
Enumeration
This entry controls the generation of parity bits in the data sent to the local DTE and the checking of the parity bit when generated by the local DTE. The options are (1) parity checking is enabled, (2) parity generation is enabled, (3) parity checking and generation are enabled, or (255) no parity checking nor parity generation.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.8.2.1.1.1.22- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- pktSwchProfileSEntry
- Table
- pktSwchProfileSTable
- Siblings
- 40
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | space |
2 | mark |
3 | even |
4 | odd |
255 | none |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pktSwchProfileNumberS The number by which a profile is identified. This is also used as the index for the profile table.
The maximum profile number is 200. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.1 |
| pktSwchProfileCRPaddingS This parameter specifies the number of padding characters to be added after a carriage
return character is transmitted to the local DTE. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.10 |
| pktSwchProfileLineFoldS This parameter specifies the maximum number of characters to be inserted before the
format effector. If the value is zero, there is no insertion of a format effector (line foldin… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.11 |
| pktSwchProfileSpeedS This parameter determines the rate of data transmission to and from the DTE. | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.12 |
| pktSwchProfilePadFlowContS This determines whether or not the terminal can exercise flow control over the PAD.
The options are either 'device can exercise flow control' or 'device cannot exercise flow
contr… | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.13 |
| pktSwchProfileLineFeedInsertS This parameter indicates when there is a line feed insertion after CR. The options are
(1) Insert line feed after transmission of CR to the DTE, (2) Insert line feed after receip… | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.14 |
| pktSwchProfileLineFeedPadS This parameter specifies the number of padding characters to be added after a line
feed. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.15 |
| pktSwchProfileEditingS This parameter specifies the editing capabilities available in the data transfer mode.
Editing is always possible when the PAD is in the command mode. The options are
(1) Comman… | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.16 |
| pktSwchProfileCharDelS This parameter specifies the character delete, which is one character from IA5. The default
selection is 127 (character DEL). | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.17 |
| pktSwchProfileLineDelS This parameter specifies the line delete (last line stored in the edit buffer), which is one character from IA5. The default
selection is 24 (character CAN). | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.18 |
| pktSwchProfileLineDispS This entry specifies the line display character, which is one character
from IA5. The default selection is 18 (character DC2). | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.19 |
| pktSwchProfileRecallCharS The character specified by this entry is used to escape from the data transfer
mode and enter the PAD command mode. The integer values have the following meanings:
(0) … | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.2 |
| pktSwchProfileEditServSigS This entry specifies the editing PAD service signals.
The integer values have the following meanings:
(0) No editing PAD service signals
(1) Ed… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.20 |
| pktSwchProfileEchomaskS The value is a sum of values (powers of two), where each value in the sum represents
a character (or characters) that is (are) included in the echo mask. The characters in the
ec… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.21 |
| pktSwchProfilePageWaitS This entry specifies the number of line feed characters counted by the PAD before the
page wait condition is entered. If the value is zero, page wait is disabled. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.23 |
| pktSwchProfileBitsPerCharS The number of data bits per character supported by the PAD. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.24 |
| pktSwchProfileDvParityS This entry selects the type of parity to be checked and or generated by the PAD
when radSPSProfileParTreat is a value other than 255. The options are
(1) space parity, (2) mark … | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.25 |
| pktSwchProfileStopBitsS This entry indicates the number of stop bits per character supported by the PAD.
The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits. | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.26 |
| pktSwchProfileSpecFlowS This entry is used to define additional flow control possiblilites.
The options are either (1) Flow control by means of the terminal DTR line
or (2) No special flow control. | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.27 |
| pktSwchProfileCountFwdS This entry can be used to instruct the PAD to complete the assembly of a packet
and to forward it after the specifed number of characters has been received.
If the value is zero, … | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.28 |
| pktSwchProfileEscDelayS This entry can be used to instruct the PAD whether to delay the forwarding of
a data packet when an escape character is detected in the data stream and to
determine the required d… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.29 |
| pktSwchProfileEchoS This determines if an echo of the input characters is retured to the DTE.
The options are either 'echo enabled' or 'no echo'. | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.3 |
| pktSwchProfileCharBreakS This entry specifies the decimal value of the character that will be interpreted
as an additional break signal by the PAD. A value of zero indicates no break character. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.30 |
| pktSwchProfileCharSuppressS This entry specifies the decimal value of the character that will toggle
echo suppression in the PAD. A value of zero indicates that echo suppression
is only controlled by radSP… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.31 |
| pktSwchProfileCharSubsS This entry specifies the decimal value of the character that will be echoed
instead of the character received from the user's DTE. A zero value indicates that
no character is ec… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.32 |
| pktSwchProfileFormFeedPadS This entry specifies the number of padding (NUL) characters that will be
automatically sent after the form feed character. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.33 |
| pktSwchProfileInactivityS This entry specifies the number of minutes after which the PAD will forward
the accumulated data and clear the call. A zero value indicates no disconnection
on inactivity. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.34 |
| pktSwchProfileOptionsS This entry defines several options to control the profile. The value is a sum of values
(powers of two), where each value in the sum represents an option .
The values that may be… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.35 |
| pktSwchProfileClrTimerS This entry specifies the number of minutes after which a call is cleared.
If the parameter value is 0, there is no disconnection timer. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.36 |
| pktSwchProfileSubAddInCUDS This entry defines the number of digits for the subaddress in CUD. | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.37 |
| pktSwchProfileStatusS The status of this profile. The choices are those defined in the SNMPv2 Textual Conventions
for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowSta… | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.38 |
| pktSwchProfileIncomingMsgS This object enables the asynchronous user to change the 'com' message for
Incoming calls to a string of up to 20 characters.
If user selects the value xxx for this object, the PA… | column | OctetString | .1.3.6.1.4.1.164.8.2.1.1.1.39 |
| pktSwchProfileDataForwCharS The value is a sum of values (powers of two), where each value in the sum represents
a character (or characters) that is (are) used as a data forwarding character. The data
forwa… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.4 |
| pktSwchProfileOutgoingMsgS This object enables the asynchronous user to change the 'com' message for
Outgoing calls to a string of up to 20 characters.
If user selects the value xxx for this object, the PA… | column | OctetString | .1.3.6.1.4.1.164.8.2.1.1.1.40 |
| pktSwchProfileClearMsgS This object enables the user to edit a message, which will appear when
the channel is cleared. The message is a string of up to 20 characters.
Example of such a string: 'Call Clea… | column | OctetString | .1.3.6.1.4.1.164.8.2.1.1.1.41 |
| pktSwchProfileIdleTimerS Packets will be forwarded when the idle timer expires. The idle time interval is specified
as a multiple of 50 milliseconds. The multiple is given by the parameter value. For e… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.5 |
| pktSwchProfileDevFlowContS This parameter determines whether or not the PAD uses software flow control for the
attached device. The options are either (1) PAD uses flow control during data transfer
mode, … | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.6 |
| pktSwchProfileServSigS This parameter is used to instruct the PAD whether to transfer PAD service signals and
the PAD prompt to the local DTE in standard format. The options are (1) PAD service
signals… | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.7 |
| pktSwchProfileBreakS The value is a sum of values (powers of two), where each value in the sum represents
a PAD operation on receipt of the break signal from the DTE.
The values that may be included i… | column | Integer32 | .1.3.6.1.4.1.164.8.2.1.1.1.8 |
| pktSwchProfileDiscOutS This parameter instructs the PAD whether to forward the user sequences included in
data packets to the local DTE or discard them. The options are (1) discard output or
(2) norma… | column | Enumeration | .1.3.6.1.4.1.164.8.2.1.1.1.9 |