mdlSCmd
RAD-MIB ·
.1.3.6.1.4.1.164.3.3.2.1.1.1.13
Object
General object for any special command at card level.
0=NotApplicable, for cards that don't support this object.
For KML.10(ISDN) card of KM-2100, the object will indicate
Manual Call Command in Switch mode. It is applicable only when
for KML.10, prtIsdnSwitchMode=manual.
KML.10 valid values:
'1' = noOp, will be used by agents that do not support this
feature or object (old KM agents)
'2' = off, Set call command mode to disconnect state. Disconnects the call.
'3' = on, Set call command mode to connect state. Connects the call.
For DXC IO cards, the object will be used for IO Card Reset HW command:
'2' = off, this will be always the Get value for these cards.
'3' = on, this is the Set command used to Reset the IO card. Upon
completing the operation, the value will automatically change to off(2),
by Agent.
For Slots that are NOT IO Slots and for empty IO Slots, the Get value will
be always '0' (NotApplicable).
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Enumerated Values
1 | unknown |
2 | notUsed |
3 | offLine |
4 | onLine |
5 | offLineRedundancy |
6 | onLineRedundancy |
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mdlSSltIdx A unique number to identify a slot position in the DACS.
The Kilomux should use enumerated values starting with kmx.
For IPmux100 use values 1-13, 20. | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.1 |
| mdlSAlrClearCmd Setting this attribute to ON, will enforce a clear
operation on the card level alarms . Upon completion,
the value will automatically change to off(2). | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.10 |
| mdlSAlrClearAllCmd Setting this attribute to ON, will enforce a clear
operation on card and port level alarms . Upon completion,
the value will automatically change to off(2). | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.11 |
| mdlSAlrMaskAll on(3) - will cause masking of all the card level alarms.
These alarms will not be sent to NMS and will not
be taken into account for Alarms Status.
off(2) - will unmask all card… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.12 |
| mdlSReset Reset action to be performed on the module. | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.14 |
| mdlSRebuildFrame Applicable only for KiloMux Main Link cards only.
'2' = off, this will be always the Get value.
'3' = on, this is the Set command used to Rebuild the Frame.
Upon completing the … | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.15 |
| mdlSBackupSwVer This attribute indicates the Backup Software version of the
card installed in the specific slot position. | column | OctetString | .1.3.6.1.4.1.164.3.3.2.1.1.1.16 |
| mdlSSecondaryBackupSwVer This attribute indicates the Secondary Backup Software version of the
card installed in the specific slot position. | column | OctetString | .1.3.6.1.4.1.164.3.3.2.1.1.1.17 |
| mdlSPiggybackVer This attribute indicates the Piggyback version of the
card installed in the specific slot position. | column | OctetString | .1.3.6.1.4.1.164.3.3.2.1.1.1.18 |
| mdlSCardType This attribute indicates the type of the card installed
in the specific slot position.
Only PS's are possible in the PS slots.
Only CL's are possible in the CL slots.
Only IO mod… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.2 |
| mdlSHwVer This attribute indicates the Hardware version of the
card installed in the specific slot position. | column | OctetString | .1.3.6.1.4.1.164.3.3.2.1.1.1.3 |
| mdlSSwVer This attribute indicates the Software version of the
card installed in the specific slot position. | column | OctetString | .1.3.6.1.4.1.164.3.3.2.1.1.1.4 |
| mdlSAlarmStatus Indicates the current alarm state only for card level.
This object will be set to:
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.5 |
| mdlSAlarmStatusAll Indicates the current card alarm state including the
lower level: card, port.
This object will be set to:
- critical(7): when there is at least one active (ON) critical
… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.6 |
| mdlSTestStatus This attribute will be on(3) when there is at least
one test running on a port of the module; otherwise the value
will be off(2). | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.7 |
| mdlSHwStatus This attribute will be fail(2) when a HW FAIL exists
on this module (discovered by periodic self test);
otherwise the value will be ok(3). | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.8 |
| mdlSActivity notApplicable - when the slot is empty (no module)
offline(1) - when the module is not active (redundant)
online (2) - when the module is active . | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.1.1.9 |