mdlIBcommand
RAD-MIB ·
.1.3.6.1.4.1.164.1.2.3.2.1.6
Object
column
r/w
Enumeration
When this object is set to the value of
open(2), the station should go into the
open state. The progress and success of
this command is given by the values of the
object mdlIBstate.
When this object is set to the value
of reset(3), then the station should do
a reset. On a reset, all MIB counters
should retain their values, if possible.
Other side effects depend on the hardware chip set.
When this object is set to the value
of close(4), the station should go into
the closed state by removing itself
from the ring.
Setting this object to a value of
no-op(1) has no effect.
For read operation, this object has always a
value of no-op(1). It is not permitted to apply this
command on an agent module.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.1.2.3.2.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- mdlIBEntry
- Table
- mdlIBTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | operational |
2 | locSyncLoss |
3 | remSyncLoss |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mdlIBid Unique number to identify the CML\IB module. It indicates the slot
number the module is inserted in | column | Integer32 | .1.3.6.1.4.1.164.1.2.3.2.1.1 |
| mdlIBLocalMacAddr The value of this object is the specific MAC address
of this interface which uniquely identifies this interface
on a ring.It is the address set by the management and
upon reque… | column | MacAddress | .1.3.6.1.4.1.164.1.2.3.2.1.10 |
| mdlIBLocalAddrStatus The value of this object specifies whether the specific
MAC address of this interface was set by the local
management or it is the burn-in address in use. | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.11 |
| mdlIBbrnInMacAddr The value of this object is the specific Burn-in MAC address
of this interface which uniquely identifies this interface
on a ring. Non-canonical format. | column | MacAddress | .1.3.6.1.4.1.164.1.2.3.2.1.12 |
| mdlIBTrapMaskEnable When this attribute is set to OFF by the management console, the
agent starts sending the unmasked traps related to this module.
Otherwise, no traps are sent by this module. | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.13 |
| mdlIBsegID Unique number to identify the segment where the CML\IB module
is inserted. It is one of the segTRID values. | column | Integer32 | .1.3.6.1.4.1.164.1.2.3.2.1.2 |
| mdlIBCorrelationEnable When set to ON(3), the in-band agent should perform
correlation each time a station enters/leaves the segment. | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.3 |
| mdlIBAutorecEnable When set to ON(3), the in-band agent should perform
autorecovery each time a beacon status is detected. | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.4 |
| mdlIBAutorecResult When autorecovery is completed the result will be reported (3)..(7).
While in autorecovery process, started(2) will be reported.
Before autorecovery process, notStarted(1) will be… | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.5 |
| mdlIBstate The current adapter status, which can
be used to diagnose fluctuating problems. | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.7 |
| mdlIBagnt Indicates whether the specific inband module serves as:
- Active hub agent - (on)
- Ring Monitor (for TR module only) - (off)
- Standby agent - (standBy) | column | Enumeration | .1.3.6.1.4.1.164.1.2.3.2.1.8 |
| mdlIBIpAddress Indicates IP address of the module if the module serves as
an agent of itself. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.164.1.2.3.2.1.9 |