ethEncapsulationCRCMode
RAD-MIB ·
.1.3.6.1.4.1.164.3.1.6.1.1.1.4
Object
column
r/w
Enumeration
This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.1.6.1.1.1.4- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ethIfEntry
- Table
- ethIfTable
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ethIfIdx A unique index of the ethernet interface/port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.1.1.1.1 |
| ethSpeed This parameter defines the line speed. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.10 |
| ethRip2 This parameter defines whether to send RIP II message
to WAN from LAN or not | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.11 |
| ethPortPriority This parameter defines if priority is to
be considered for this Port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.12 |
| ethPortMngEnable This parameter defines whether management data can pass through this Port.
localOnly (4) - Only local device can be managed via this port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.13 |
| ethFlowCtrlMacAddress In case of flow control - transmit frame with this specific MAC address
to inform the other end to stop sending frames.
Default: 01.80.C2.00.00.01. | column | MacAddress | .1.3.6.1.4.1.164.3.1.6.1.1.1.14 |
| ethRateLimit This parameter defines the Rate Limit of the line, in Mbps. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.1.1.1.15 |
| ethJumboFrameEnable This parameter defines whether to support Jumbo Frame or not. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.16 |
| ethAutoMdiXEnable This parameter defines whether to support
automatic change between MDI and MDI[X]. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.17 |
| ethPortDataEnable This parameter defines whether this port is enabled
for data (that is not management).
no(2) - management can run on this port
yes(3) - both management and payload data can run on… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.18 |
| ethIfUse This parameter defines the use of the port.
1=NET
2=USER . | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.1.1.1.19 |
| ethMode This object indicates the Ethernet mode of operation. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.2 |
| ethLineOam This parameter defines the working mode of 802.AH OAM mechanism. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.20 |
| ethRoutingProtocol This parameter defines the routing protocol
used above ETH port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.21 |
| ethMdiXManualSwitch This parameter sets the port to be MDI-X (cross-over) or
MDI (straight-through).
It is applicable only when ethAutoMdiXEnable = no, namely,
only when the automatic MDI/MDIX cros… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.22 |
| ethDot1xEnable Determines if the Port-Based Network Access Protocol
(IEEE-802.1x) is enabled for the Ethernet Port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.23 |
| ethPartnerRateMode For converters having couples of ports, where each couple contains
a port with an SFP connector and a port with a RJ connector, this
parameter is relevant for the SFP port. It a… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.24 |
| ethDot1xPortRole Determine the functionality of the port in
the Port-Based Network Access Protocol (IEEE-802.1x) -
either Authenticator or Supplicant. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.25 |
| ethBridgingMode This object indicates the bridging mode of the Ethernet
interface. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.3 |
| ethBackPressure This parameter defines whether to enable or disable Back pressure.
Back Pressure is a flow control parameter. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.5 |
| ethLimit4 This parameter determine the Back off algorithm mode.
Every 4 following collisions the Framer will be thrown out
(4 times more than usuall). | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.6 |
| ethSkipInitReset This parameter defines whether read status on reset. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.7 |
| ethMulticastBlock This parameter defines whether to send multicast message to WAN from LAN or not. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.8 |
| ethBroadcastBlock This parameter defines whether to send broadcast message to WAN from LAN or not. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.1.1.1.9 |