atmSuPortAtmCnfgShapingMode
RAD-MIB ·
.1.3.6.1.4.1.164.12.4.2.3.1.1.9
Object
column
r/w
Enumeration
ATM Shaping mode. Three possible values: SW Shaping. HW Shaping - APC with NCITS = 1. HW Shaping - APC with NCITS = 2 The difference between the two hardware modes is in the connection cell granularity and maximum bandwidth (BW): * For NCITS=1, the granularity is of one cell and the max. BW is the uplink BW, * For NCITS=2, the granularity is of every two cells and the max. BW is half of the uplink BW.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.12.4.2.3.1.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- atmSuPortAtmCnfgEntry
- Table
- atmSuPortAtmCnfgTable
- Siblings
- 10
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| atmSuPortAtmCnfgIdleCellCLP Determines the clp bit value for transmition
in empty time slots. | column | Enumeration | .1.3.6.1.4.1.164.12.4.2.3.1.1.1 |
| atmSuPortAtmSNMPTrafficDescrIndex The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL. | column | ATM-TC-MIBAtmTrafficDescrParamIndex | .1.3.6.1.4.1.164.12.4.2.3.1.1.10 |
| atmSuPortAtmTrafficDescrIndex The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to whole ATM WAN port. | column | ATM-TC-MIBAtmTrafficDescrParamIndex | .1.3.6.1.4.1.164.12.4.2.3.1.1.11 |
| atmSuPortAtmCnfgScramble Determined by the standards if the cell will be scrambled or not. | column | Enumeration | .1.3.6.1.4.1.164.12.4.2.3.1.1.2 |
| atmSuPortAtmSNMPVpi The Vcc Vpi for SNMP requests. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.12.4.2.3.1.1.3 |
| atmSuPortAtmSNMPVci The Vcc Vci for SNMP requests. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.12.4.2.3.1.1.4 |
| atmSuPortAtmSNMPStatus value indicates if the SNMP Vcc is available for management. | column | Enumeration | .1.3.6.1.4.1.164.12.4.2.3.1.1.5 |
| atmSuPortAtmILMIStatus Value indicates if agent should respond to ILMI requests from the
Atm switch or forward it.
note: when using Atm to Frame-Relay configuration this value should be
active to … | column | Enumeration | .1.3.6.1.4.1.164.12.4.2.3.1.1.6 |
| atmSuPortAtmSNMPIp The interface IP address for SNMP requests. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.164.12.4.2.3.1.1.7 |
| atmSuPortAtmCnfgCDVOptimization value indicates if optimization of CDV (Cell Delay Varation)
is enbabled. | column | Enumeration | .1.3.6.1.4.1.164.12.4.2.3.1.1.8 |