agnCOffsetCmd
RAD-MIB ·
.1.3.6.1.4.1.164.3.1.2.2.9
Object
scalar
r/w
Enumeration
An object defining special user request.
notApplicable - is RO value for products that do not support this object.
normal - nothing special
u1 - user 1 - for all Voice cards, the DISPLAYED Tx and Rx Levels
will have the following Offsets:
- 2 Wires port: Tx Level: the base value (for 0dBm) = 0
Rx Level: the base value (for 0dBm) = -2
- 4 Wires port: Tx Level: the base value (for 0dBm) = -16
Rx Level: the base value (for 0dBm) = 7
The MIB and application DB will use the values without Offset.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.1.2.2.9- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- cnfgAgnGen
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | ddMMYYYY |
2 | mmDDYYYY |
4 | yyyyMMDD |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| agnCSanityCheckCmd Setting this attribute to on(3) will initiate the process
of Sanity check on the TmpCnfg. Upon completion the value
will automatically be changed to off(2). | scalar | Enumeration | .1.3.6.1.4.1.164.3.1.2.2.1 |
| agnCT1E1RingTable Configuration of all T1/E1 Ring ML cards and ports.
The write operation into the table objects is valid only
for the TmpCnfg.
A Slot/Port that does not participate in the T1/E1 Ri… | table | - | .1.3.6.1.4.1.164.3.1.2.2.10 |
| agnCMainExitPort An object defining the Main Exit Port for the Data of the device.
In the Vmux-120 Device the Data can Exit via one of the 2 existing ports:
1. Ethernet port (2)
2. A port that can… | scalar | Enumeration | .1.3.6.1.4.1.164.3.1.2.2.11 |
| agnCBuMlTable Configuration for Primary, Secondary and Third Link.
These are used for Link Backup. | table | - | .1.3.6.1.4.1.164.3.1.2.2.12 |
| agnCQ50Table Table for the device Q50 parameters.
Q50 is a Signaling protocol used between PBX devices.
It is possible to control the initiation of calls using Q.50.
This is useful for devices… | table | - | .1.3.6.1.4.1.164.3.1.2.2.13 |
| agnCSaveCnfgIdxCmd This attribute specifies the Id of the target RealCnfg to
which the TmpCnfg should be transferred. Upon set command the
MUX will initiate the Sanity-Check process first. If
succe… | scalar | Integer32 | .1.3.6.1.4.1.164.3.1.2.2.2 |
| agnCLoadCnfgIdxCmd This attribute specifies the Id of the source Cnfg to be
loaded into the TmpCnfg. Upon set operation the actual
transfer will be initiated.
The operation is valid only on Valid co… | scalar | Integer32 | .1.3.6.1.4.1.164.3.1.2.2.3 |
| agnCClkSrcTable All the entries of this table are identical (have the same
value) for all the configurations (1..100) except the
TmpCnfg.
The write operation into the Table Objects is valid only
… | table | - | .1.3.6.1.4.1.164.3.1.2.2.4 |
| agnCDeleteCnfgIdxCmd Setting this attribute will delete the requested DB
from the NVRAM . | scalar | Integer32 | .1.3.6.1.4.1.164.3.1.2.2.5 |
| agnCDefaultCnfgIdxCmd Setting this attribute will define the desired working
configuration when no conditions of the Flip DB Table are
fulfilled and no Net GO command was issued. This command
will be a… | scalar | Integer32 | .1.3.6.1.4.1.164.3.1.2.2.6 |
| agnCnfgDataTable This table contains data about the agent configurations.
The table will support only data about valid configurations
of the agent. | table | - | .1.3.6.1.4.1.164.3.1.2.2.7 |
| agnCnfgAlarm | node | - | .1.3.6.1.4.1.164.3.1.2.2.8 |