prtT1E1LineMode

RAD-Dacs-MIB · .1.3.6.1.4.1.164.3.3.3.2.2.1.25

Object

column r/w Enumeration

Interface type of the port.
For T1 - csu, dsu are the valid values
For E1 - dsu, ltu are the valid values

Context

MIB: RAD-Dacs-MIB
OID: .1.3.6.1.4.1.164.3.3.3.2.2.1.25
Type: column
Access: readwrite
Status: current
Parent: prtT1E1CnfgEntry
Table: prtT1E1CnfgTable
Siblings: 36

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	notApplicable
`2`	csu
`3`	dsu
`4`	ltu

Related Objects

Sibling Objects

Object	Type	Syntax	OID
prtT1E1CnfgIdx This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.	column	Integer32	`.1.3.6.1.4.1.164.3.3.3.2.2.1.1`
prtT1E1CGA This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparent mode. When one of the links (main/su…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.10`
prtT1E1IdleCode This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) .	column	OctetString	`.1.3.6.1.4.1.164.3.3.3.2.2.1.11`
prtT1E1OosSignal 'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service perio…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.12`
prtT1E1VoiceOos Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.	column	OctetString	`.1.3.6.1.4.1.164.3.3.3.2.2.1.13`
prtT1E1DataOos Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.	column	OctetString	`.1.3.6.1.4.1.164.3.3.3.2.2.1.14`
prtT1E1LineLengthMask This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Opt…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.15`
prtT1E1TxGainMask This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.16`
prtT1E1InbandMng A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the management is internal to the frame. It takes p…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.17`
prtT1E1InbandMngRate A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.18`
prtT1E1DedicatedTs The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of the T1/E1 port. It is applicabl…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.3.3.2.2.1.19`
prtT1E1PrtIdx This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the p…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.3.3.2.2.1.2`
prtT1E1InbandMngRoutProt Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values …	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.20`
prtT1E1LinkMode regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an internal T1/E1 port of a T3/E3 card, TS0…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.21`
prtT1E1Multiplier The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.22`
prtT1E1RxGain This attribute is the rx volume (dB).	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.23`
prtT1E1RAI Remote Alarm Signal	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.24`
prtT1E1TS0SaBits This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets: The order (in hexa displa…	column	OctetString	`.1.3.6.1.4.1.164.3.3.3.2.2.1.26`
prtT1E1ConnectedTS This parameter indicates if there is any connected TS for this interface.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.27`
prtT1E1Ts0SaBit This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefore it is sent.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.28`
prtT1E1SameFeCnfg This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote device. Read-Write access is applicable only in G732N…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.29`
prtT1E1Slt This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.3`
prtT1E1RemCrc4 This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.30`
prtT1E1MaxTSs This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only when sysCIntTsAllocMode=static(2). 255=not appli…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.3.3.2.2.1.31`
prtT1E1EocTsConfig This object indicates whether the use of EOC for TS Configuration is enabled or not.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.32`
prtT1E1Role This object indicates whether this port behaves as SUB or Main link.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.33`
prtT1E1PppEchoFailDetection This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Dis…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.34`
prtT1E1CasOosPattern This objects defines the Cas Out-Of-Service code space (1) - see prtT1E1CasOosSpaceCode below mark (2) - see prtT1E1CasOosMarkCode below spaceMark (3) - transmit 'space' for 2 se…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.36`
prtT1E1CasOosSpaceCode This objects defines the Cas Out-Of-Service code The value that will be transmitted when prtT1E1CasOosPattern = space (1). default = 14.	column	Unsigned32	`.1.3.6.1.4.1.164.3.3.3.2.2.1.37`
prtT1E1CasOosMarkCode This objects defines the Cas Out-Of-Service code The value that will be transmitted when prtT1E1CasOosPattern = mark (2). default = 1.	column	Unsigned32	`.1.3.6.1.4.1.164.3.3.3.2.2.1.38`
prtT1E1LineType This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably ca…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.4`
prtT1E1LineCode This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. jbzs=b7zs refers the Ja…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.5`
prtT1E1SignalMode 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is in use. 'bitOriented'…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.6`
prtT1E1Fdl This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following i…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.7`
prtT1E1FdlMode Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port.	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.8`
prtT1E1Sync This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds…	column	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.2.1.9`